Subject: I don'see where is my CDROM for mounting it?
To: None <port-i386@netbsd.org>
From: Richard PLOIX <richard.ploix@fr.adp.com>
List: port-i386
Date: 12/10/1999 18:19:18
Hello,
my config is : DELL Pentium 200 Pro, 1 SCSI disk 2.5 Go target 0, 1 SCSI
disk 8.4 Go target 1, 1 SCSI CDROM target 5.
I don't see who is the CDROM.
I've trying /dev/cd0a, /dev/cd0d, /dev/cd1a, /dev/cd1d, /dev/sd0a,
/dev/sd0d, /dev/sd1a, /dev/sd1d, /dev/sd5a, /dev/sd5d.
nothing was good for mounting my CDROM by the command line : mount -rt
cd9660 /dev/sdxx /mnt/cdrom.
the directory /mnt/cdrom exists.
I've trying the same thing in the fstab file: /dev/xxxx /mnt/cdrom cd9660
ro,noauto 0 0.
Here is my dmesg.log file:
-------------------------->
NetBSD 1.4.1 (GENERIC) #1: Tue Aug 10 00:03:09 MEST 1999

fvdl@struis:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: family 6 model 1
step 9
cpu0: Intel Pentium Pro (686-class)
real mem  = 66715648
avail mem =
58339328
using 840 buffers containing 3440640 bytes of memory
mainbus0
(root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o enabled,
memory enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82441FX PCI and
Memory Controller (PMC) (rev. 0x02)
pcib0 at pci0 dev 13 function 0
pcib0:
Intel 82371SB PCI-to-ISA Bridge (PIIX3) (rev. 0x01)
pciide0 at pci0 dev 13
function 1: Intel 82371SB IDE Interface (PIIX3)
pciide0: bus-master DMA
support present
pciide0: primary channel wired to compatibility
mode
pciide0: disabling primary channel (no drives)
pciide0: secondary
channel wired to compatibility mode
pciide0: secondary channel ignored
(disabled)
ppb0 at pci0 dev 14 function 0: Digital Equipment DECchip 21052
PCI-PCI Bridge (rev. 0x01)
pci1 at ppb0 bus 1
pci1: i/o enabled, memory
enabled
ex0 at pci1 dev 8 function 0: 3Com 3c905-TX 10/100 Ethernet
ex0:
interrupting at irq 11
ex0: MAC address 00:c0:4f:b6:5b:e0
nsphy0 at ex0 phy
24: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX,
100baseTX, 100baseTX-FDX, auto
ahc1 at pci1 dev 11 function 0
ahc1:
interrupting at irq 10
ahc1: aic7880 Wide Channel, SCSI Id=7, 16
SCBs
scsibus0 at ahc1 channel 0: 16 targets, 8 luns per target
ahc1: target
0 synchronous at 10.0MHz, offset = 0xf
sd0 at scsibus0 targ 0 lun 0:
<SEAGATE, ST32550N, 0019> SCSI2 0/direct fixed
sd0: 2047MB, 3511 cyl, 11
head, 108 sec, 512 bytes/sect x 4194058 sectors
ahc1: target 1 synchronous
at 10.0MHz, offset = 0xf
sd1 at scsibus0 targ 1 lun 0: <QUANTUM, FIREBALL
SE8.4S, PJ0A> SCSI2 0/direct fixed
sd1: 8191MB, 7637 cyl, 8 head, 274 sec,
512 bytes/sect x 16777215 sectors
ahc1: board is not responding
cmd
fail
probe(ahc1:5:0): timed out in datain phase, SCSISIGI ==
0x44
probe(ahc1:5:0): asserted ATN - device reset in message buffer
ahc1:
board is not responding
cmd fail
sd2 at scsibus0 targ 5 lun 0: <, , > SCSI0
0/direct fixed
ahc1: board is not responding
ahc1: board is not
responding
sd2: mode sense (4) returned nonsense; using fictitious
geometry
ahc1: board is not responding
cmd fail
sd2: 40960MB, 40960 cyl, 64
head, 32 sec, 512 bytes/sect x 83886081 sectors
vga1 at pci0 dev 16
function 0: S3 Trio32/64 (rev. 0x54)
wsdisplay0 at vga1: console (80x25,
vt100 emulation)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4:
ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a,
working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
sb0 at isa0 port
0x220-0x237 irq 5 drq 1 drq2 5: dsp v4.13
audio0 at sb0: full duplex
opl0
at sb0: model OPL3
midi0 at opl0: <SB Yamaha OPL3>
pckbc0 at isa0 port
0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd
slot
wskbd0 at pckbd0: console keyboard
opms0 at pckbc0 (aux slot)
pckbc0:
using irq 12 for aux slot
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC
speaker>
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play
device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0
port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head,
18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask 440 netmask c40
ttymask 1cc2
wscons: wskbd0 glued to wsdisplay0 (console)
sd0: no disk
label
sd2(ahc1:5:0): timed out in dataout phase, SCSISIGI == 0x0
ahc1:
Issued Channel A Bus Reset #1. 6 SCBs aborted
findroot: can't open dev sd2a
(5)
ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
ahc1: target 1
synchronous at 10.0MHz, offset = 0xf
ahc1: target 5 synchronous at 10.0MHz,
offset = 0xf
boot device: sd1
root on sd1a dumps on sd1b
root file system
type: ffs
wsdisplay0: screen 4 added (80x25, vt100
emulation)
----------------------->