Hi, folks...  I'm new to PCMCIA, so I'd appreciate it if someone with
some more experience could help me get my modem card up and running.

I've got a Toshiba Satellite 2110CS with a 3Com 3C589 and Megahertz 14.4
modem card.  The ethernet's working fine, but I'm getting stray
interrupts from the modem card and when I try to connect to the tty
device that is attached to the card, I get a hangup from cu.

I've enabled PCMCIADEBUG (for the stuff in sys/dev/pcmcia--I just put
it in pcmciareg.h and commented out the definition in pcmcia.c).  I'm
including the dmesg output for a session where I booted without the
3Com card installed, so it was just the modem card--I then tried cu
(which failed) and inserted the 3Com card.  As I said, I'm new to
pcmcia.  If anyone has any ideas on what I can try next, I'd love to
hear them.  It looks to me in just glancing at the code, that the card
is enabled, then disabled on each 'stray' interrupt.  I did notice that
the ethernet card picked up the same interrupt number when it was
installed.

Any ideas?

-allen

NetBSD 1.3F (LYNX) #1: Mon Jun  8 23:05:54 EDT 1998
    briggs@backup:/usr/src/sys/arch/i386/compile/LYNX
cpu0: family 4 model 8 step 0
cpu0: Intel 486DX4 (486-class)
real mem  = 20774912
avail mem = 17244160
using 279 buffers containing 1142784 bytes of memory
mainbus0 (root)
isa0 at mainbus0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
lpt0 at isa0 port 0x378-0x37b irq 7
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atapibus0 at wdc0
wd0 at wdc0 drive 0: <IBM-DSOA-20810>
wd0: using 16-sector 16-bit pio transfers, lba mode
wd0: 775MB, 1587600 sec, 512 bytes/sec
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
vt0 at isa0 port 0x60-0x6f irq 1
vt0: generic, 80 col, color, 8 scr, mf2-kbd, [R3.32]
vt0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
pcic0 at isa0 port 0x3e0-0x3e1 iomem 0xd0000-0xd3fff: using irq 3
pcic0: controller 0 (Intel 82365SL Revision 1) has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia0: CIS version 2.0 or 2.01
pcmcia0: CIS info: MEGAHERTZ, XJ2144, A5, PCMCIA MODEM
pcmcia0: Manufacturer code 0x102, product 0x5
pcmcia0: function 0: serial port, ccr addr 200 mask 1
pcmcia0: function 0, config table entry 32: I/O card; irq mask 3c; iomask 0, iospace 3f8-3ff; rdybsy_active wp_active bvd_active io8 irqlevel
pcmcia0: function 0, config table entry 33: I/O card; irq mask 3c; iomask 0, iospace 2f8-2ff; rdybsy_active wp_active bvd_active io8 irqlevel
pcmcia0: function 0, config table entry 34: I/O card; irq mask 3c; iomask 0, iospace 3e8-3ef; rdybsy_active wp_active bvd_active io8 irqlevel
pcmcia0: function 0, config table entry 35: I/O card; irq mask 3c; iomask 0, iospace 2e8-2ef; rdybsy_active wp_active bvd_active io8 irqlevel
com2 at pcmcia0 function 0pcmcia0: card irq 5
pcmcia0: ++enabled_count = 1
pcmcia0: function 0 CCR at 0 offset 200: 7f ff 7f ff, ff 7f ff 7f, ff
 port 0x2f8-0x2ff: ns16550a, working fifo
pcmcia0: --enabled_count = 0
pcmcia0: function 0 CCR at 0 offset 200: ff ff ff ff, ff ff ff ff, ff
pcmcia1 at pcic0 controller 0 socket 1
apm0 at mainbus0: Power Management spec V1.1
apm0: battery life expectancy: 1%
apm0: A/C state: on
apm0: battery charge state: low charging
apm0: estimated 0m
biomask 4040 netmask 4040 ttymask 40ca
stray interrupt 5
WARNING: old BSD partition ID!
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
uvm_swap: allocated 138 swap buffer headers
pcmcia0: card irq 5
pcmcia0: ++enabled_count = 1
pcmcia0: function 0 CCR at 0 offset 200: 7f ff 7f ff, ff 7f ff 7f, ff
pcmcia0: --enabled_count = 0
stray interrupt 5
pcmcia0: card irq 5
pcmcia0: ++enabled_count = 1
pcmcia0: function 0 CCR at 0 offset 200: 7f ff 7f ff, ff 7f ff 7f, ff
pcmcia0: --enabled_count = 0
stray interrupt 5
pcmcia1: CIS version 2.0 or 2.01
pcmcia1: CIS info: 3Com Corporation, 3C589D, TP/BNC LAN Card Ver. 2a, 000002
pcmcia1: Manufacturer code 0x101, product 0x589
pcmcia1: function 0: network adapter, ccr addr 10000 mask 3
pcmcia1: function 0, config table entry 1: I/O card; irq mask ffff; iomask 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
pcmcia1: function 0, config table entry 3: I/O card; irq mask ffff; iomask 4, iospace 0-f; rdybsy_active wp_active bvd_active io8 io16 irqlevel
ep0 at pcmcia1 function 0pcmcia1: ++enabled_count = 1
pcmcia1: function 0 CCR at 0 offset 0: 41 0 0 0, 0 0 0 0, 0
 port 0x330-0x33f: 3Com 3C589 Ethernet
ep0: MAC address 00:60:97:91:1a:92
ep0: 8KB byte-wide FIFO, 5:3 Rx:Tx split, utp/aui/bnc (default utp)
pcmcia1: --enabled_count = 0
pcmcia1: function 0 CCR at 0 offset 0: ff ff ff ff, ff ff ff ff, ff
pcmcia1: card irq 5
pcmcia1: ++enabled_count = 1
pcmcia1: function 0 CCR at 0 offset 0: 41 0 0 0, 0 0 0 0, 0