Hi thanks for reading,

After a couple of responses here some extra info from the message file after
booting.


Here is the complete message file.

Jan H. van Gils

PS - The termination on the SCSI bus is Ok
   - IT is not possible to change the BIOS address because
     it is PCI device and it wants to choose the address it
     is using 0xC8000

---------------------------------------------------------------

Copyright (c) 1996, 1997 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The regents of the University of California. All rights reserved.

NetBSD 1.3 (INSTALL) #0: Tue Dec 30 18:42:52 EST 1997
    perry@jekyll.peirmont.com:/usr/src/sys/arch/i386/compile/INSTALL
cpu0: family 5 model 6 step 1
cpu0: AMD K6 (586-class)
real mem = 33161216
avial mem = 29569024
using 430 buffers containing 1761280 bytes of memory
mainbus0 (root)
pci0 at mainbus 0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7100 (rev. 0x01)
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x8086 product 0x7100 (rev. 0x01)
vendor 0x8086 product 0x7110 (IDE mass storage, interface 0x80, revision 0x01)
    at pci0 dev 1 function 1 not confifured
vendor 0x8086 product 0x7112 (USB serial bus, revision 0x01) at pci0 dev 1
    function 2 not configured
vendor 0x8086 product 0x7113 (miscaellaneous bridge, revision 0x01) at pci0 dev
    1 function 3 not configured
vendor 0x1023 product 0x9440 (VGA display, revision 0xe3) at pci0 dev 11
    function 0 not configured
bha2 at pci0 dev 12 function 0: BusLogic 9xxC SCSI
bha2: interrupting at irq 11
bha2: model BT-946C, firmware 4.19
bha2: sync, parity
bha2: targ 0: sync, offset 15, period 100nsec
scsibus0 at bha2: 8 targets
sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST31230N, 0594> SCSI2 0/direct fixed
sd0: 1010MB, 3992 cyl, 5 head, 103 sec, 512 bytes/sect x 2069860 sectors
isa0 at pcib0
ep0 at isa0 port 0x310-0x31f irq 10: 3Com Ethernet
ep0: Mac address 00:20:af:bf:76:18
ep0: 8KB byte-wide FIFO, 5:3 Rx:Tx split, utp/aui/bnc (default bnc)
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
wdc0 at isa0 port 0x1f0-0x1f7 ira 14
atapibus0 at wdc0
wd0 at wdc0 drive 0: <Maxtor 7546 AT>
wd0: 521MB, 1060 cyl, 16 head, 63 sec, 512 bytes/sec
wd0: using 16-sector 16-bit pio transfers, lba adressing
wdc1 at isa0 port 0x170-0x177 irq 15
atapibus1 at wdc1
cd0 at atapibus1 drive 0: <Pioneer CD-ROM ATAPI Model DR-A12X 0100, , E100A>
    type 5 cdrom removable
npx0 at isa0 port 0xf0-0xff: using exception 16
pc0 at isa0 port 0x60-0x6f irq 1: color
pc0: console
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
biomask c840 netmask cc40 ttymask cc42
md0: internal 1537K image area
boot device: fd0
root on md0a dump on md0b
root file system type: ffs

starting sysinst

- option install NetBSD
	message
	wd0: no disk label
sd0(bha2:0:0): timed out
sd0(bha2:0:0): timed out AGAIN


- With regards
- Jan H. van Gils (e-Mail janvg@knoware.nl)