Hello,

I just installed more SCSI devices on my peecee (moved them over from an
Amiga).  I'm having lots of problems with the NetBSD 1.2 NCR driver.  The
log looks like this:

sd0 at scsibus0 targ 1 lun 0: <HP, 97536SD       LJ, DG06> SCSI1 0/direct fixed
sd0: ncr0:1: ERROR (80:140) (e-2e-0) (e0/13) @ (440:868b0000).
        script cmd = 60000008
        reg:     da 10 80 13 47 e0 01 1f 01 0e 00 ae 80 00 0e 00.
ncr0: handshake timeout
ncr0: restart (scsi reset).
sd0(ncr0:1:0): COMMAND FAILED (6 ff) @0xf8783000.
sd0(ncr0:1:0): asynchronous.
sd0(ncr0:1:0): M_REJECT sent for 1-3-1-5d-8.
ncr0:1: ERROR (80:4) (8-0-0) (e0/13) @ (544:900b0000).
        script cmd = 910a0000
        reg:     da 00 80 13 47 e0 01 1f 01 08 00 00 80 00 02 02.
ncr0: aborting job ...
ncr0:1: ERROR (90:0) (8-0-0) (e0/13) @ (9d8:900b0000).
        script cmd = 72100000
        reg:     da 00 80 13 47 e0 01 1f 01 08 00 00 80 00 02 02.
ncr0: restart (fatal error).
sd0(ncr0:1:0): COMMAND FAILED (9 ff) @0xf8783000.
sd0(ncr0:1:0): asynchronous.
sd0(ncr0:1:0): M_REJECT sent for 1-3-1-5d-8.
ncr0:1: ERROR (80:4) (8-0-0) (e0/13) @ (544:900b0000).
        script cmd = 910a0000
        reg:     da 00 80 13 47 e0 01 1f 01 08 00 00 80 00 07 02.
ncr0: aborting job ...
ncr0:1: ERROR (90:0) (8-0-0) (e0/13) @ (9d8:900b0000).
        script cmd = 72100000
        reg:     da 00 80 13 47 e0 01 1f 01 08 00 00 80 00 07 02.
ncr0: restart (fatal error).
sd0(ncr0:1:0): COMMAND FAILED (9 ff) @0xf8783000.
sd0(ncr0:1:0): phase change 6-3 6@005f01c8 resid=5.
sd0(ncr0:1:0): asynchronous.
sd0(ncr0:1:0): COMMAND FAILED (4 88) @0xf8783000.
sd0(ncr0:1:0): command aborted, data = 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
sd0: could not mode sense (4); using fictitious geometry



Then, when trying to write to the Wangtek QIC drive:



ncr0:2: ERROR (80:140) (8-2a-0) (0/13) @ (544:900b0000).
        script cmd = 910a0000
        reg:     da 10 80 13 47 00 02 1f 01 08 00 2a 80 00 0a 00.
ncr0: handshake timeout
ncr0: restart (scsi reset).
st0(ncr0:2:0): COMMAND FAILED (6 ff) @0xf87b9a00.
ncr0:2: ERROR (80:140) (8-2a-0) (0/13) @ (544:900b0000).
        script cmd = 910a0000
        reg:     da 10 80 13 47 00 02 1f 01 08 00 2a 80 00 0a 00.
ncr0: handshake timeout
ncr0: restart (scsi reset).
st0(ncr0:2:0): COMMAND FAILED (6 ff) @0xf87b9a00.



The only thing I can do is to mount the Chinon CD-ROM.  Everything else
seems to fail (including disklabeling the HP disk).

Is it possible to grab the new NCR driver in -current and drop it into
1.2 tree?  Any help greatly appreciated.

  -jm

-- 

                     ---> http://www.jmp.fi/~jmarin/ <---