I decided to finally start upgrading my 1.4U WorkPad z50.

I'm about to go on a trip, so I decided to do the safe thing and just
upgrade the kernel and X11. The text console is much faster (yay!) and
Xhpc comes up fine (although I have to be root).

However, the cursor does not move when I use the pointer stick thingy that
works fine in WinCE. Fortunately the default in startx has the login xterm
under the cursor, so I can exit X11 by typing at the console (whew).

I also tried building xsrc-current from a day or so ago, but that didn't
behave any differently (except that it tried to install 8 megs more stuff,
which overflowed my SanDisk 192 CF until I removed some catman pages).

Now I am back down to kernel+X11 from 20000627-1.5_ALPHA and base userland
from 20000315-1.4U. And now, the dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5_ALPHA (GENERIC) #0: Sat Jul  1 02:05:42 JST 2000
    root@680g.naobsd.org:/usr/src/sys/arch/hpcmips/compile/GENERIC
IBM WorkPad z50 2601 1AU (NEC VR4121 rev0.0 131.072MHz)
total memory = 49152 KB
avail memory = 42896 KB
using 640 buffers containing 2560 KB of memory
/usr/src/sys/arch/hpcmips/vr/vr.c(294): vr_bus_reset() not implemented.
mainbus0 (root)
cpu0 at mainbus0: NEC VR4100 CPU (0xc60) Rev. 6.0 with software emulated floating point Rev. 0.0
cpu0: L1 cache: 16KB/16B instruction, 8KB/16B data, direct mapped
cpu0: No L2 cache
cpu0: install VR specific idle routine
bivideo0 at mainbus0: pseudo video controller, console
hpcfb0 at bivideo0: hpcrasops 640x480 pixels, 65536 colors, 80x48 chars: tvram redraw
wsdisplay0 at hpcfb0: console (std, vt100 emulation)
vrip0 at mainbus0
vrcmu0 at vrip0 addr 0xb000060-0xb00007f
vrgiu0 at vrip0 addr 0xb000100-0xb00011f intr 8
button0 at vrgiu0 port=1 id=5 active=low sense=edge
button1 at vrgiu0 port=2 id=9 active=low sense=edge
vrbcu0 at vrip0 addr 0xb000000-0xb00001f
vrbcu: cpu 131.072MHz, bus 32.768MHz, ram 32.768MHz
com0 at vrip0 addr 0xc000000-0xc000007 intr 9: ns16550a, working fifo
vrrtc0 at vrip0 addr 0xb0000c0-0xb0000df intr 2
vrkiu0 at vrip0 addr 0xb000180-0xb00019f intr 7
wskbd0 at vrkiu0 (mux 1 ignored for console): console keyboard, using wsdisplay0
vrpmu0 at vrip0 addr 0xb0000a0-0xb0000bf intr 1
vrdsu0 at vrip0 addr 0xb0000e0-0xb0000e7
vrpiu0 at vrip0 addr 0xb000120-0xb0002bf intr 5
wsmouse0 at vrpiu0 mux 0
vrisab0 at vrgiu0:ISA port 0x15000000-0x18000000 mem 0x10000000-0x20000000
isa0 at vrisab0
pcic0 at isa0 port 0x3e0-0x3e1 iomem 0x70000-0x73fff irq 589827
pcic0: controller 0 (Intel 82365SL Revision 1) has sockets A and B
pcic0: controller 1 (Intel 82365SL Revision 1) has sockets A and B
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
pcmcia at pcic0 controller 1 socket 0 not configured
pcmcia at pcic0 controller 1 socket 1 not configured
btnmgr0 at mainbus0
wskbd1 at btnmgr0 mux 1
/usr/src/sys/arch/hpcmips/vr/vr.c(294): vr_bus_reset() not implemented.
pcic0: using irq 589827 for socket events
wdc1 at pcmcia0 function 0 port 0x15000400-0x1500040f
wd0 at wdc1 channel 0 drive 0: <SanDisk SDCFB-192>
wd0: drive supports 1-sector pio transfers, lba addressing
wd0: 183 MB, 734 cyl, 16 head, 32 sec, 512 bytes/sect x 375808 sectors
pcmcia1: CIS checksum failed
ne0 at pcmcia1 function 0 port 0x300-0x30f port 0x310-0x31f
ne0: Socket Communications Low Power Ethernet CF Ethernet
ne0: Ethernet address 00:c0:1b:00:b7:f1
boot device: wd0
root on wd0a dumps on wd0b
pcmcia0: card irq 3
pcmcia0: card irq 3
pcmcia0: card irq 3
pcmcia0: card irq 3
WARNING: preposterous clock chip time
 -- CHECK AND RESET THE DATE!
root file system type: ffs
pcmcia1: card irq 3

Todd Whitesel
toddpw @ best.com