Hello,

I tried to netboot my 712/100 and 712/100XC, but both stop at the same step as is seems, so I append only one console output. Is something wrong with my kernel config? I used GENERIC and only commented out "pseudo-device raid" and "options RAID_AUTOCONFIG".

Here's the output:
>> NetBSD/hp700 LIF/FFS/LFS Boot, Revision 1.2
>> (root@minas-morgul.hitzemann.org, Sat Nov  1 12:57:14 CET 2003)
>> Enter "reset" to reset system.
Boot: [[[lf0a:]netbsd][-a][-c][-d][-s][-v][-q]] :- netbsd -s
5042176+81920+331776 [597200+132916]=0x7175f0
Start @ 0x200000 [1=0x865000-0x9175f0]...
SPID bits: 0x0, error = -2
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.6ZE (SIMON) #3: Sat Nov  1 13:32:18 CET 2003
	root@minas-morgul.hitzemann.org:/usr/src/sys/arch/hp700/compile/SIMON
HP9000/715/100XC (Mirage Sr.)
real mem = 65536 KB (73728 reserved for PROM, 55932 KB used by NetBSD)
avail mem = 51440 KB
using 844 buffers containing 3376 KB of memory
mainbus0 (root) [flex fff80000]
pdc0 at mainbus0
mem0 at mainbus0 hpa fffbf000: viper rev 0, ctrl 40400100 size 64MB
cpu0 at mainbus0 hpa fffbe000 irq 31 ipl 0: PA7100LC (Hummingbird) rev 6
cpu0: PCX-L, PA-RISC 1.1c, lev 1, cat A, 100 MHz clk
cpu0: shadows, 512K/512K D/I caches, 64 shared TLB, 8 shared BTLB
cpu0: PCX-L (CMOS-26B) floating point, rev 1
"WAX Bus Adapter" at mainbus0 (type b, sv 8e) hpa f0200000 not configured
"WAX EISA Bus Adapter" at mainbus0 (type b, sv 90) hpa fc000000 not configured
lasi0 at mainbus0 hpa f0000000 irq 28: rev 3.0
gsc0 at lasi0
"PS/2 port" at gsc0 (type a, sv 84) hpa f0108100 not configured
"PS/2 port" at gsc0 (type a, sv 84) hpa f0108000 not configured
"floppy controller" at gsc0 (type a, sv 83) hpa f010a000 not configured
"Advanced audio (ext.)" at gsc0 (type a, sv 7b) hpa f0104000 not configured
lpt0 at gsc0 hpa f0102000 irq 7 ipl 1
"Core RS-232C" at gsc0 (type a, sv 8c) hpa f0105000 not configured
ie0 at gsc0 hpa f0107000 irq 8 ipl 2: v2.0 address 08:00:09:d3:34:82, type LASI/i82596CA
osiop0 at gsc0 hpa f0106000 irq 9 ipl 3: NCR53C710 rev 2, 40MHz, SCSI ID 7
scsibus0 at osiop0: 8 targets, 8 luns per target
"GIO Graphics" at mainbus0 (type a, sv 85) hpa f8000000 not configured
biomask 00000038 netmask 0000003c ttymask 0000007e
symb[rbit].bitno == cix!!!
symb[rbit].bitno == cix!!!
symb[rbit].bitno == cix!!!


Best regards,
  Simon