On Wed, Feb 22, 2006 at 08:43:01PM -0800, Garrett D'Amore wrote:
> I'd love to hear feedback.

I don't think you can run the cube in big endian mode (if you could, it's
not well documented).

Here are the boot messages - pci memory space fails, and the readclock
thing is .. strange.

Thanks for looking at this!

Martin
(Too bad they didn't add a connector for aumac1 :-( )

Start = 0x800a0000, range = (0x800a0000,0x8035853f), format = SREC
MIPS32/64 params: cpu arch: 32
MIPS32/64 params: TLB entries: 32
MIPS32/64 params: Icache: line = 32, total = 16384, ways = 4
                 sets = 128
MIPS32/64 params: Dcache: line = 32, total = 16384, ways = 4
                 sets = 128
  picache_stride    = 4096
  picache_loopcount = 4
  pdcache_stride    = 4096
  pdcache_loopcount = 4
  Dcache is coherent
  Icache is coherent against Dcache
Memory size: 0x04000000
Loaded initial symtab at 0x803299a4, strtab at 0x8033ef58, # entries 5365
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.15 (MTX-1) #0: Thu Feb 23 09:12:23 CET 2006
	martin@night-porter.duskware.de:/usr/src/sys/arch/evbmips/compile/MTX-1
4G Systems MTX-1
total memory = 65536 KB
avail memory = 60300 KB
mainbus0 (root)
cpu0 at mainbus0: 324.00MHz (hz cycles = 632813, delay divisor = 324)
cpu0: Alchemy Au1500 (Rev 2 core) (0x1030202) Rev. 2 with software emulated floating point
cpu0: 16KB/32B 4-way set-associative L1 Instruction cache, 32 TLB entries
cpu0: 16KB/32B 4-way set-associative write-back L1 Data cache
obio0 at mainbus0
aubus0 at mainbus0
aucom0 at aubus0 addr 0x11100000 irq 0: Au1X00 UART, working fifo
aucom0: console
aucom1 at aubus0 addr 0x11400000 irq 3: Au1X00 UART, working fifo
aurtc0 at aubus0 addr 0x0: Au1X00 programmable clock
aumac0 at aubus0 addr 0x11500000 irq 28: Au1X00 10/100 Ethernet
aumac0: Ethernet address 00:0e:56:00:02:2c
sqphy0 at aumac0 phy 31: Seeq 84220 10/100 media interface, rev. 0
sqphy0: using Seeq 84220 isolate/reset hack
sqphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
aumac1 at aubus0 addr 0x11510000 irq 29: Au1X00 10/100 Ethernet
aumac1: Ethernet address 00:0e:56:00:12:2c
ohci0 at aubus0 addr 0x10100000 irq 26: Alchemy OHCI
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
aupci0 at aubus0 addr 0x14005000: Alchemy Host-PCI Bridge, 66MHz
pci0 at aupci0 bus 0
pci0: i/o space, memory space enabled
wi0 at pci0 dev 0 function 0: can't map mem space
augpio0 at aubus0 addr 0x11900100: Alchemy GPIO, primary block
gpio0 at augpio0: 23 pins
augpio1 at aubus0 addr 0x11700000: Alchemy GPIO, secondary block
gpio1 at augpio1: 16 pins
uhub0: device problem, disabling port 1
root device: 
use one of: aumac0 aumac1 wi0 ddb halt reboot
root device: aumac0
dump device: 
file system (default generic): 
root on aumac0
mountroot: trying ffs...
mountroot: trying nfs...
nfs_boot: trying DHCP/BOOTP
aumac0: link state changed to UP
nfs_boot: DHCP next-server: 192.168.150.7
nfs_boot: my_domain=duskware.de
nfs_boot: my_addr=192.168.150.148
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.150.10
root on 192.168.150.7:/usr/exp/hosts/evbmips
root time: 0x43fd6f56
root file system type: nfs
readclock: 1870/4/25/21/4/9
WARNING: preposterous clock chip time
setclock: 6/2/23/8/16/22
 -- CHECK AND RESET THE DATE!
init path (default /sbin/init): 
init: copying out path `/sbin/init' 11
setclock: 6/2/23/8/58/47