Hi Jim,

What a nice surprise! Thanks a lot!

I've downloaded/burned/tested the restore image
4.0_BETA2restorecd200708290002Z.iso, and this is what I get on Qube 2
with Ralink pci card upon reboot:

# dmesg
Cchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:33:37
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 125000000 Hz quality 100
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <Maxtor 34098H4>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 32253 MB, 65530 cyl, 16 head, 63 sec, 512 bytes/sect x 66055244 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
syncing disks... done
unmounting file systems...unter Copyright (c) 1996, 1997, 1998, 1999,
2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_BETA2 (GENERIC) #0: Wed Aug 29 11:04:18 PDT 2007
        builds@wb36:/home/builds/ab/netbsd-4/cobalt/200708290002Z-obj/home/builds/ab/netbsd-4/src/sys/arch/cobalt/compile/GENERIC
Cobalt Qube 2
total memory = 65536 KB
avail memory = 59980 KB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev. 10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:39:ed
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision
0x02) at pci0 dev 9 function 2 not configured
ral0 at pci0 dev 10 function 0: Ralink Technologies RT2560 802.11b/g (rev. 0x01)
ral0: interrupting at irq 9
ral0: 802.11 address 00:0e:2e:50:49:1a
ral0: MAC/BBP RT2560 (rev 0x04), RF RT2525
ral0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ral0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:33:37
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 125000000 Hz quality 100
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <Maxtor 34098H4>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 32253 MB, 65530 cyl, 16 head, 63 sec, 512 bytes/sect x 66055244 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
#

Now I'm off to trying to compile some packages and kernels...

Max