On 7/20/07, Izumi Tsutsui <tsutsui@ceres.dti.ne.jp> wrote:
> I get base.tgz and kern-GENERIC.tgz from the same directory,
> then now I see that it works on RaQ1 with 64MB RAM but
> not on RaQ2 with 256MB:
> ...
> I suspect that there is some memory corruption in bootloader
> around bootinfo, but I'll check what actually happens there.

The Qube 2 used here to test 4.0_BETA2 also has 256MB RAM.  It's dmesg
when 3.1 was loaded is:

NetBSD 3.1 (GENERIC) #0: Tue Oct 31 01:09:51 UTC 2006
        builds@b0.netbsd.org:/home/builds/ab/netbsd-3-1-RELEASE/cobalt/200610302053Z-obj/home/builds/ab/netbsd-3-1-RELEASE/src/sys/arch/cobalt/compile/GENERIC
total memory = 256 MB
avail memory = 247 MB
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev. 10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:e2:09
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision
0x02) at pci0 dev 9 function 2 not configured
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:d0:1a
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <ST3160023A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs