On 12/28/05, Izumi Tsutsui <tsutsui@ceres.dti.ne.jp> wrote:
> In article <78a2305a0512271847r1201a7fbg18c1f34428498ba7@mail.gmail.com>
> acruhl@gmail.com wrote:
>
> > I'm running 3.0 on my Qube 2, and I got a panic when ftp'ing to the
> > Qube and getting files.
>
> Please post dmesg and exact comand you tried.
> I can't reproduce the panic on my RaQ2...

I didn't run a command, I ftp'd to the Qube from another machine
(NetBSD 3.0 on amd64 to be precise). Here's the line I have in
inetd.conf:

ftp             stream  tcp     nowait  root    /usr/libexec/ftpd       ftp=
d -ll

Then I did a get of some 300 meg files, but it crashed maybe 5 megs
after I started the get.

I think the core didn't dump out completely because gdb says it isn't
a core file.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.0 (GENERIC) #0: Sun Dec 18 22:39:34 UTC 2005
        builds@b3.netbsd.org:/home/builds/ab/netbsd-3-0-RELEASE/cobalt/2005=
12182024Z-obj/home/builds/ab/netbsd-3-0-RELEASE/src/sys/arch/cobalt/compile=
/GENERIC
total memory =3D 160 MB
avail memory =3D 153 MB
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev. =
10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:ab:25
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision
0x02) at pci0 dev 9 function 2 not configured
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:ab:18
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <IC35L060AVER07-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200 sect=
ors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs