On Saturday, July 2, 2005, at 07:08 AM, Philip Plant wrote:

>
> OK.  Are you sure that you have good network cabling and also that your
> speed and duplex settings are correct?  Don't trust auto-negotiation,
> make sure that the settings are right.

Thanks for the reply.

Downloads of stuff for pkgsrc come thru at quite fast, no loss, so  
that's OK.  wire-test fails but then it also fails on my OSX box so I  
guess that's OK.  How do I check the settings other than dmesg output?

I'm not sure why my csh shells spend so much time in pause, see the  
output of top earlier.
It takes me 45 sec to ls /usr/pkgsrc/www.

I'm working on rebuilding a kernel locally, but it's not a fast process.

Any other system stats that would be useful to look at?

Here's the dmesg from this bootup, tlp1 looks fine to me. I"m not sure  
what else to check.  With 1.6.1 I got continual messages about the SCSI  
card, so I disabled SCSI in kernel, but I'm not getting any message  
with this 2.0-CURRENT kernel from 6/21/05 (IIRC that's what the build  
of the .iso was from).  But my first thought was to build my own  
locally with a bunch of stuff disabled and see what happens.   
adjustkernel needs perl and that's been compiling for a bit.

Thanks,

Brian

qube# dmesg
4
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision  
0x02) at pci0 dev 9 function 2 not configured
ahc0 at pci0 dev 10 function 0: Adaptec 2940 Ultra SCSI adapter
ahc0: interrupting at irq 9
ahc0: aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
scsibus0 at ahc0: 8 targets, 8 luns per target
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:01:36:d1
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <Maxtor 6Y060L0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200  
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using  
DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
syncing disks... done
unmounting file systems...Copyright (c) 1996, 1997, 1998, 1999, 2000,  
2001, 2002, 2003, 2004, 2005
     The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University of California.  All rights reserved.

NetBSD 3.99.3 (GENERIC) #1: Sat May 14 13:25:21 CEST 2005
          
root@netbsd20.s-zone.org:/Data/NetBSD/cobalt/obj/sys/arch/cobalt/ 
compile/GENERIC
total memory = 128 MB
avail memory = 121 MB
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU  
Rev. 10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB  
entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev  
1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:01:36:ca
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
VIA Technologies VT83C572 USB Controller (USB serial bus, revision  
0x02) at pci0 dev 9 function 2 not configured
ahc0 at pci0 dev 10 function 0: Adaptec 2940 Ultra SCSI adapter
ahc0: interrupting at irq 9
ahc0: aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
scsibus0 at ahc0: 8 targets, 8 luns per target
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:01:36:d1
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
wd0 at atabus0 drive 0: <Maxtor 6Y060L0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 58644 MB, 119150 cyl, 16 head, 63 sec, 512 bytes/sect x 120103200  
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using  
DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs