All,

After verifying the cd would boot (virtual pc) I started my laptop with it,
boots fine. Then I started the Raq2, the LCD shows some info so does the
console, so far so good. Suddenly kernel panic, disk too small... I'll be
damned. I use 512MB SSD's and though it would work (CD is only ~200 megs) to
create two ultra silent webservers, guess not.

Why does it needs so much space or does it use predefined sizes?

Marcel


[Console output]


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.6.1 (INSTALL.LCD) #0: Thu Jun 26 22:29:11 CEST 2003

cdi@merlin.camelot.net:/misc/home/cdi/src/netbsd/1.6.1/src/sys/arch/cobalt/c
ompile/INSTALL.LCD
256 MB memory, 234 MB free, 13208 KB in 3302 buffers
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a,
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev.
10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:5f:6e
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Symbios Logic 53c860 (SCSI mass storage, revision 0x02) at pci0 dev 8
function 0
 not configured
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 (Apollo VP) PCI-ISA Bridge, rev 37
pciide0 at pci0 dev 9 function 1: VIA Technologies VT82C586 (Apollo VP)
ATA33 co
ntroller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 1: <512MB CHH>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 488 MB, 993 cyl, 16 head, 63 sec, 512 bytes/sect x 1000944 sectors
wd0: 32-bit data port
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:1): using PIO mode 0
pciide0: secondary channel configured to compatibility mode
pciide0: disabling secondary channel (no drives)
VIA Technologies VT83C572 USB Controller (USB serial bus, revision 0
 dev 9 function 2 not configured
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:5f:6f
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
lcd0 at mainbus0
boot device: <unknown>
root on tlp0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 10.0.0.254
nfs_boot: my_domain=mfg.cobaltmicro.com
nfs_boot: my_addr=10.0.0.160
nfs_boot: my_mask=255.0.0.0
root on 10.0.0.254:/nfsroot
warning: no /dev/console
init: Creating mfs /dev
Tue Mar  8 19:53:15 GMT 2005
Starting file system checks:
Coming up: fixing /dev...
Coming up: fixing /var...
Preparing the installation...
Setting tty flags.
Setting sysctl variables:
Starting network.
Hostname: client
Configuring network interfaces:.
Building databases...
kvm_mkdb: machdep.booted_kernel: the value is not available: No such file or
dir
ectory
Mounting all filesystems...
Checking quotas: done.
Setting securelevel: kern.secu
/etc/rc: WARNING: No swap space configured!
starting local daemons:wd0: no disk label

 ------------------------------------------------ 
  Setting up the disk...
 ------------------------------------------------ 

mknod: /dev/lcd: File exists

 ------------------------------------------------ 
  Clearing partition information...
 ------------------------------------------------ 

wd0: no disk label
wd0: no disk label
wd0: no disk label
wd0: no disk label

 ------------------------------------------------
  Setting up the Ext2 partition...
 ------------------------------------------------

wd0: no disk label

 ------------------------------------------------
  Setting up swap...
 ------------------------------------------------

wd0: no disk label

 ------------------------------------------------
  PANIC: disk is too small...
 ------------------------------------------------

Tue Mar  8 19:53:58 GMT 2005

NetBSD/cobalt (client) (tty00)

login: