Subject: Re: Acer PICA memory type
To: Bob Meader <port-arc@netbsd.org>
From: Chris Rupnik <crupnik@videotron.ca>
List: port-arc
Date: 06/25/2002 12:15:55
Bob,
 This was the trick. The 4x36 simms I have worked fine. The machine was set
for 2 8MB simms, while I had 4 4MB simms. Explains why it failed to post
after exactly 4MB (it looking for another 4mb).

 Thanks again, Strange to see the machine boot into WINNT 3.1.. Ahhh Program
Manager....

Chris

----- Original Message -----
From: "Bob Meader" <bob@cci.net>
To: <port-arc@netbsd.org>
Cc: <crupnik@videotron.ca>
Sent: Thursday, June 20, 2002 12:40 PM
Subject: RE: Acer PICA memory type


> I have the following dip switch setings
> for the memory board for a  NEC RISC Station (a ACER PICA OEM).
> Maybe this applies MIPS magnum PC-50 Pica as well.
>
> Memory Configuration for the NEC RISC Station (NEC OEM ACER)
>
>
> Switch Switch Switch Switch Switch Switch Switch Switch Switch
> Config 1 2 3 4 5 6 7 8 9
>
> Four 4-MB Sticks Off Off Off On On On On On On
> Two 8-MB Sticks Off Off Off Off Off Off On Off Off
> Off Off Off On On On On Off Off
> Four 8-MB Sticks Off Off Off On Off Off On Off Off
> Two 16-MB Sticks Off Off Off Off Off Off Off On Off
> Off Off Off On On On Off On Off
> Off Off Off On Off Off Off On Off
> Four 16-MB Sticks Off Off Off Off On Off Off On Off
> Two 32-MB Sticks Off Off Off Off Off Off Off Off On
> Off Off Off On On On Off Off On
> Off Off Off On Off Off Off Off On
> Off Off Off Off On Off Off Off On
> Off Off Off Off Off On Off Off On
>
>
> -----Original Message-----
> From: port-arc-owner@netbsd.org [mailto:port-arc-owner@netbsd.org]On
> Behalf Of M. Warner Losh
> Sent: Wednesday, June 19, 2002 7:40 PM
> To: crupnik@videotron.ca
> Cc: port-arc@netbsd.org
> Subject: Re: Acer PICA memory type
>
>
> In message: <006d01c20bd9$af1f5470$0a01a8c0@PLANETEORANGE.CA>
>             "Chris Rupnik" <crupnik@videotron.ca> writes:
> :  I have attempted to put the 1X36 (4MB) simms in combinations of 2 and 4
> : that were in my MIPS magnum PC-50 into the PICA, but all I get is a
memory
> : error upon POST
> :  The pica page listed here
http://assist.acer.com/public/articles/566.htm
> : only says
> : "MEMORY       :16MB SIMM UPGRADEABLE TO 128MB"
> :
> : What should I be using instead?
>
> Are you sure they are 1x36 and not 1x32?  I've had problems with
> non-parity memory in my Deskstation rPC44, dating from the same
> period.  I've also had problems with the new "three chip" designs,
> where the "nine chip" designs work w/o a hassle.  I've also had better
> luck with 16MB simms than with 4MB ones.  Of course, it doesn't hurt
> to have 64MB of RAM in these beasts (but the RAM is so slow that the
> benefits of MIPS is wasted due to long waits for memory).
>
> Warner
>