Re: Problems installing on a recent (Kaby Lake) system

[Dave Huang <khym%azeotrope.org@localhost>]

On Thu, Mar 23, 2017 at 03:00:44PM -0500, Dave Huang wrote:
> Booting BIOS USB image
> ------------------------
> And finally, I tried NetBSD-7.99.66-amd64-install.img. Similarly to
> booting the ISO in BIOS mode, it shows the boot menu on the redirected
> serial console. And it has problems loading the kernel, though it
> seems to be a different problem:
> 
> Option 1 will be chosen in 0 seconds.
> 18185936+813132+1005492 [1173288+805075|
> 
> And it hangs there with no spinning progress.

I was able to get booting the BIOS USB image to work... I think the
kernel loaded, but the BIOS serial console redirection stopped working
so it looked like it hung? In any case, I went to the boot prompt and
did "consdev com1" and was able to boot. It didn't see the USB drive I
booted off of though, but with the serial console working, I was able
to look through the kernel messages and saw that it reported some sort
of device error and disabled the USB port. I moved the USB drive to a
different port (I think it was a port closer to the root hub),
rebooted, switched to serial console, and the kernel saw the boot
device as sd1.

However, the install wasn't able to remount root read-write--it
apparently was trying to mount /dev/sd0a instead of /dev/sd1a (sd0 is
another USB flash drive that I want to install NetBSD on). I didn't
note the exact error message, but it was something to the effect of:
mount: no match for `/dev/sd0a'

/etc/fstab showed root on /dev/sd0a rather than /dev/sd1a, but sysctl
kern.root_device = sd1. Not sure what creates /etc/fstab, but
apparently it didn't do the right thing. I manually did mount -u
/dev/sd1a /, ran sysinst, and was able to install NetBSD :)

Now I just need to figure out how to create a filesystem on these
disks... apparently raidframe's RAID 6 is untested?
https://wiki.netbsd.org/projects/project/raidframe-raid6/

(I must admit that I'm probably going to end up installing FreeNAS on
this machine, but I'm a NetBSD kind of guy and wanted to see how
NetBSD fares on it :)

Here's the dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.66 (GENERIC.201703221740Z)
total memory = 32589 MB
avail memory = 31622 MB
cpu_rng: RDSEED
rnd: seeded with 128 bits
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Supermicro Super Server (0123456789)
mainbus0 (root)
ACPI: RSDP 0x00000000000F05B0 000024 (v02 SUPERM)
ACPI: XSDT 0x000000007D7BD0A8 0000D4 (v01 SUPERM SUPERM   01072009 AMI  00010013)
ACPI: FACP 0x000000007D7DF790 00010C (v05                 01072009 AMI  00010013)
ACPI: DSDT 0x000000007D7BD218 022571 (v02 SUPERM SMCI--MB 01072009 INTL 20120913)
ACPI: FACS 0x000000007DD57F80 000040
ACPI: APIC 0x000000007D7DF8A0 000084 (v03                 01072009 AMI  00010013)
ACPI: FPDT 0x000000007D7DF928 000044 (v01                 01072009 AMI  00010013)
ACPI: FIDT 0x000000007D7DF970 00009C (v01                 01072009 AMI  00010013)
ACPI: SPMI 0x000000007D7DFA10 000040 (v05 SUPERM SMCI--MB 00000000 AMI. 00000000)
ACPI: MCFG 0x000000007D7DFA50 00003C (v01 SUPERM SMCI--MB 01072009 MSFT 00000097)
ACPI: HPET 0x000000007D7DFA90 000038 (v01 SUPERM SMCI--MB 01072009 AMI. 0005000B)
ACPI: LPIT 0x000000007D7DFAC8 000094 (v01 INTEL  GNLR     00000000 MSFT 0000005F)
ACPI: SSDT 0x000000007D7DFB60 000248 (v02 INTEL  sensrhub 00000000 INTL 20120913)
ACPI: SSDT 0x000000007D7DFDA8 002BAE (v02 INTEL  PtidDevc 00001000 INTL 20120913)
ACPI: SSDT 0x000000007D7E2958 000BE3 (v02 INTEL  Ther_Rvp 00001000 INTL 20120913)
ACPI: DBGP 0x000000007D7E3540 000034 (v01 INTEL           00000000 MSFT 0000005F)
ACPI: DBG2 0x000000007D7E3578 000054 (v00 INTEL           00000000 MSFT 0000005F)
ACPI: PRAD 0x000000007D7E35D0 0000CA (v02 PRADID PRADTID  00000001 INTL 20120913)
ACPI: SSDT 0x000000007D7E36A0 00547E (v02 SaSsdt SaSsdt   00003000 INTL 20120913)
ACPI: UEFI 0x000000007D7E8B20 000042 (v01                 00000000      00000000)
ACPI: SSDT 0x000000007D7E8B68 000E73 (v02 CpuRef CpuSsdt  00003000 INTL 20120913)
ACPI: DMAR 0x000000007D7E99E0 000070 (v01 INTEL  SKL      00000001 INTL 00000001)
ACPI: EINJ 0x000000007D7E9A50 000130 (v01 AMI    AMI.EINJ 00000000 AMI. 00000000)
ACPI: ERST 0x000000007D7E9B80 000230 (v01 AMIER  AMI.ERST 00000000 AMI. 00000000)
ACPI: BERT 0x000000007D7E9DB0 000030 (v01 AMI    AMI.BERT 00000000 AMI. 00000000)
ACPI: HEST 0x000000007D7E9DE0 00027C (v01 AMI    AMI.HEST 00000000 AMI. 00000000)
ACPI: Executed 22 blocks of module-level executable AML code
ACPI: Executed 3 blocks of module-level executable AML code
ACPI: 6 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0
cpu0: Intel(R) Pentium(R) CPU G4560 @ 3.50GHz, id 0x906e9
cpu1 at mainbus0 apid 2
cpu1: Intel(R) Pentium(R) CPU G4560 @ 3.50GHz, id 0x906e9
cpu2 at mainbus0 apid 1
cpu2: Intel(R) Pentium(R) CPU G4560 @ 3.50GHz, id 0x906e9
cpu3 at mainbus0 apid 3
cpu3: Intel(R) Pentium(R) CPU G4560 @ 3.50GHz, id 0x906e9
acpi0 at mainbus0: Intel ACPICA 20170119
acpi0: X/RSDT: OemId <SUPERM,  SUPERM,01072009>, AslId <AMI ,00010013>
mpacpi: PCI bus 5 int routing already done!
acpi0: MCFG: segment 0, bus 0-255, address 0x00000000e0000000
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE886FA27410 00037F (v02 PmRef  Cpu0Cst  00003001 INTL 20120913)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE813A27C810 0006E4 (v02 PmRef  Cpu0Ist  00003000 INTL 20120913)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE813A2F3810 0005AA (v02 PmRef  ApIst    00003000 INTL 20120913)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFFE813A185290 000119 (v02 PmRef  ApCst    00003000 INTL 20120913)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 24000000 Hz quality 2000
acpiec0 at acpi0 (H_EC, PNP0C09-1)acpiec0: unable to evaluate _GPE: AE_NOT_FOUND
pckbc1 at acpi0 (PS2K, MSFT0001) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, MSFT0003) (aux port): irq 12
SIO1 (PNP0C02) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
FWHD (INT0800) at acpi0 not configured
LDRC (PNP0C02) at acpi0 not configured
LDR2 (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
CWDT (INT3F0D) at acpi0 not configured
SPMI (IPI0001) at acpi0 not configured
PDRC (PNP0C02) at acpi0 not configured
IOTR (PNP0C02) at acpi0 not configured
EPC (INT0E0C) at acpi0 not configured
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
PEPD (INT33A1) at acpi0 not configured
acpibut1 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
PMT1 (ACPI000D) at acpi0 not configured
PTID (INT340E) at acpi0 not configured
acpifan0 at acpi0 (FAN0, PNP0C0B-0): ACPI Fan
acpifan1 at acpi0 (FAN1, PNP0C0B-1): ACPI Fan
acpifan2 at acpi0 (FAN2, PNP0C0B-2): ACPI Fan
acpifan3 at acpi0 (FAN3, PNP0C0B-3): ACPI Fan
acpifan4 at acpi0 (FAN4, PNP0C0B-4): ACPI Fan
acpitz0 at acpi0 (TZ00)
acpitz0: active cooling level 0: 71.0C
acpitz0: active cooling level 1: 55.0C
acpitz0: active cooling level 2: 50.0C
acpitz0: active cooling level 3: 45.0C
acpitz0: active cooling level 4: 40.0C
acpitz0: levels: critical 119.0 C
acpitz1 at acpi0 (TZ01)
acpitz1: levels: critical 119.0 C, passive cooling
ACPI: Enabled 6 GPEs in block 00 to 7F
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 8086 product 590f (rev. 0x05)
vendor 8086 product a135 (miscellaneous prehistoric, revision 0x31) at pci0 dev 19 function 0 not configured
xhci0 at pci0 dev 20 function 0: vendor 8086 product a12f (rev. 0x31)
xhci0: interrupting at msi0 vec 0
xhci0: xHCI version 1.0
usb0 at xhci0: USB revision 3.0
usb1 at xhci0: USB revision 2.0
vendor 8086 product a131 (miscellaneous DASP, revision 0x31) at pci0 dev 20 function 2 not configured
vendor 8086 product a13a (miscellaneous communications, revision 0x31) at pci0 dev 22 function 0 not configured
vendor 8086 product a13b (miscellaneous communications, revision 0x31) at pci0 dev 22 function 1 not configured
ahcisata0 at pci0 dev 23 function 0: vendor 8086 product a102 (rev. 0x31)
ahcisata0: interrupting at ioapic0 pin 16
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.31, 8 ports, 32 slots, CAP 0xe334ff47<EMS,PSC,SSC,PMD,SAM,ISS=0x3=Gen3,SCLO,SAL,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
atabus6 at ahcisata0 channel 6
atabus7 at ahcisata0 channel 7
ppb0 at pci0 dev 28 function 0: vendor 8086 product a110 (rev. 0xf1)
ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci0 dev 29 function 0: vendor 8086 product a118 (rev. 0xf1)
ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
ppb1: link is x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
wm0 at pci2 dev 0 function 0: I210-T1 Ethernet Server Adapter (rev. 0x03)
wm0: for TX and RX interrupting at msix1 vec 0 affinity to 0
wm0: for TX and RX interrupting at msix1 vec 1 affinity to 1
wm0: for TX and RX interrupting at msix1 vec 2 affinity to 2
wm0: for TX and RX interrupting at msix1 vec 3 affinity to 3
wm0: for LINK interrupting at msix1 vec 4
wm0: PCI-Express bus
wm0: 2048 words FLASH(HW), version 3.25, Image Unique ID 000005cc
wm0: Ethernet address 0c:c4:7a:e2:02:a4
wm0: Copper
ukphy0 at wm0 phy 1: OUI 0x000ac2, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb2 at pci0 dev 29 function 1: vendor 8086 product a119 (rev. 0xf1)
ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
ppb2: link is x1 @ 2.5GT/s
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
wm1 at pci3 dev 0 function 0: I210-T1 Ethernet Server Adapter (rev. 0x03)
wm1: for TX and RX interrupting at msix2 vec 0 affinity to 0
wm1: for TX and RX interrupting at msix2 vec 1 affinity to 1
wm1: for TX and RX interrupting at msix2 vec 2 affinity to 2
wm1: for TX and RX interrupting at msix2 vec 3 affinity to 3
wm1: for LINK interrupting at msix2 vec 4
wm1: PCI-Express bus
wm1: 2048 words FLASH(HW), version 3.25, Image Unique ID 000005d0
wm1: Ethernet address 0c:c4:7a:e2:02:a5
wm1: Copper
ukphy1 at wm1 phy 1: OUI 0x000ac2, model 0x0000, rev. 0
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb3 at pci0 dev 29 function 2: vendor 8086 product a11a (rev. 0xf1)
ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 8.0GT/s
ppb3: link is x1 @ 2.5GT/s
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
ppb4 at pci4 dev 0 function 0: vendor 1a03 product 1150 (rev. 0x03)
ppb4: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
genfb0 at pci5 dev 0 function 0: vendor 1a03 product 2000 (rev. 0x30)
pcib0 at pci0 dev 31 function 0: vendor 8086 product a149 (rev. 0x31)
vendor 8086 product a121 (miscellaneous memory, revision 0x31) at pci0 dev 31 function 2 not configured
ichsmb0 at pci0 dev 31 function 4: vendor 8086 product a123 (rev. 0x31)
ichsmb0: interrupting at ioapic0 pin 16
iic0 at ichsmb0: I2C bus
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
com1: console
pcppi0 at isa0 port 0x61
spkr0 at pcppi0: PC Speaker
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer1: attached to pcppi0
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
acpicpu0: C2: FFH, lat 151 us, pow   200 mW
acpicpu0: C3: FFH, lat 256 us, pow   200 mW
acpicpu0: P0: FFH, lat  10 us, pow 54000 mW, 3500 MHz
acpicpu0: P1: FFH, lat  10 us, pow 49609 mW, 3300 MHz
acpicpu0: P2: FFH, lat  10 us, pow 45377 mW, 3100 MHz
acpicpu0: P3: FFH, lat  10 us, pow 43320 mW, 3000 MHz
acpicpu0: P4: FFH, lat  10 us, pow 39829 mW, 2800 MHz
acpicpu0: P5: FFH, lat  10 us, pow 35972 mW, 2600 MHz
acpicpu0: P6: FFH, lat  10 us, pow 32273 mW, 2400 MHz
acpicpu0: P7: FFH, lat  10 us, pow 28714 mW, 2200 MHz
acpicpu0: P8: FFH, lat  10 us, pow 27447 mW, 2100 MHz
acpicpu0: P9: FFH, lat  10 us, pow 24094 mW, 1900 MHz
acpicpu0: P10: FFH, lat  10 us, pow 20888 mW, 1700 MHz
acpicpu0: P11: FFH, lat  10 us, pow 17815 mW, 1500 MHz
acpicpu0: P12: FFH, lat  10 us, pow 15297 mW, 1300 MHz
acpicpu0: P13: FFH, lat  10 us, pow 13874 mW, 1200 MHz
acpicpu0: P14: FFH, lat  10 us, pow 11128 mW, 1000 MHz
acpicpu0: P15: FFH, lat  10 us, pow  8512 mW,  800 MHz
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3505242860 Hz quality 3000
uhub0 at usb0: vendor 8086 (0x8086) xHCI Root Hub (0000), class 9/0, rev 1.00/1.00, addr 0
uhub0: 10 ports with 10 removable, self powered
uhub1 at usb1: vendor 8086 (0x8086) xHCI Root Hub (0000), class 9/0, rev 2.00/1.00, addr 0
uhub1: 16 ports with 16 removable, self powered
IPsec: Initialized Security Association Processing.
ahcisata0 port 0: device present, speed: 6.0Gb/s
ahcisata0 port 3: device present, speed: 6.0Gb/s
ahcisata0 port 4: device present, speed: 6.0Gb/s
ahcisata0 port 5: device present, speed: 6.0Gb/s
ahcisata0 port 2: device present, speed: 6.0Gb/s
ahcisata0 port 1: device present, speed: 6.0Gb/s
wd0 at atabus0 drive 0
wd0: <WDC WD30EFRX-68EUZN0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
uhub2 at uhub1 port 9: vendor 0557 (0x557) product 7000 (0x7000), class 9/0, rev 2.00/0.00, addr 2
uhub2: single transaction translator
uhub2: 4 ports with 3 removable, self powered
umass0 at uhub0 port 3 configuration 1 interface 0
umass0: SanDisk (0x781) Ultra Fit (0x5583), rev 3.00/1.00, addr 1
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, Ultra Fit, 1.00> disk removable
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1 at atabus1 drive 0
wd1: <WDC WD30EFRX-68EUZN0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
sd0: 14663 MB, 29792 cyl, 16 head, 63 sec, 512 bytes/sect x 30031250 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd2 at atabus2 drive 0
wd2: <WDC WD30EFRX-68EUZN0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd3 at atabus3 drive 0
wd3: <WDC WD30EFRX-68EUZN0>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd3(ahcisata0:3:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd4 at atabus4 drive 0
wd4: <WDC WD30EFRX-68EUZN0>
wd4: drive supports 16-sector PIO transfers, LBA48 addressing
wd4: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
wd4: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd4(ahcisata0:4:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd5 at atabus5 drive 0
wd5: <WDC WD30EFRX-68EUZN0>
wd5: drive supports 16-sector PIO transfers, LBA48 addressing
wd5: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
wd5: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd5(ahcisata0:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uhidev0 at uhub2 port 1 configuration 1 interface 0
uhidev0: vendor 0557 (0x557) product 2419 (0x2419), rev 1.10/1.00, addr 3, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
uhidev1 at uhub2 port 1 configuration 1 interface 1
uhidev1: vendor 0557 (0x557) product 2419 (0x2419), rev 1.10/1.00, addr 3, iclass 3/1
ums0 at uhidev1: 3 buttons and Z dir
wsmouse1 at ums0 mux 0
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
pad0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 44100
spkr1 at audio0: PC Speaker (synthesized)
WARNING: 1 error while detecting hardware; check system log.
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
kern.module.path=/stand/amd64/7.99.66/modules
ipmi0: version 2.0 interface KCS iobase 0xca2/2 spacing 1


-- 
Name: Dave Huang         |  Mammal, mammal / their names are called /
INet: khym%azeotrope.org@localhost |  they raise a paw / the bat, the cat /
FurryMUCK: Dahan         |  dolphin and dog / koala bear and hog -- TMBG
Dahan: Hani G Y+C 39 Y++ L+++ W- C++ T++ A+ E+ S++ V++ F- Q+++ P+ B+ PA+ PL++