Re: Kabini

[Anders Lindgren <ali%df.lth.se@localhost>]

On Mon, 11 Aug 2014, Andy Ball wrote:

> Hello,
>
>    I've had good experience experimentally with an Intel
> Atom 330 'Diamondville' mITX board.  I have considered the
> D510 'Pineview' as a suitable replacement but I've also
> seen AMD's new Socket AM1 platform as a possible
> alternative.  Does anyone have experience with NetBSD on
> 'Kabini' chips or their 'Zacate' (E-350 and E-450)
> predecessors?  I doubt we would use 3D but I would consider
> it helpful if we had hardware accelleration of 2D and
> perhaps video playback.  Hopefully somebody has tried AMD
> and is willing to share his or her experiences.

  I've got two dualcore E-350D Zacate mITX-boxes, each with 4G RAM, a 
RAID1 data mirror and a 60G SSD as system disk. So far they work just fine 
with NetBSD-6.1.2 - probably time to upgrade, seeing as 6.1.4 is already 
out the door!

  I effectively run these as headless servers with negligible workload, 
and I have never fiddled with animals like DRM and the like, but I could 
easily try X/video playback and hdaudio on the box running as file server 
at home if there's anything in particular you want to know. Attached is a 
dmesg from one of these boxes.

Regards,
ali:)

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.1.2 (GENERIC)
total memory = 3821 MB
avail memory = 3695 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
To Be Filled By O.E.M. To Be Filled By O.E.M. (To Be Filled By O.E.M.)
mainbus0 (root)
ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 
0x0000000000000000/0x1 (20110623/tbfadt-586)
cpu0 at mainbus0 apid 0: AMD E-350D APU with Radeon(tm) HD Graphics, id 0x500f20
cpu1 at mainbus0 apid 1: AMD E-350D APU with Radeon(tm) HD Graphics, id 0x500f20
ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <ALASKA,   A M I,01072009>, AslId <AMI ,00010013>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
AMDN (PNP0C01) at acpi0 not configured
S800 (PNP0C02) at acpi0 not configured
SIO1 (PNP0C02) at acpi0 not configured
CIR (NTN0530) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
RMSC (PNP0C02) at acpi0 not configured
NBRM (PNP0C02) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
UAR1 (PNP0501) at acpi0 not configured
BROD (PNP0C02) at acpi0 not configured
acpivga0 at acpi0 (VGA): ACPI Display Adapter
acpiout0 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
acpiout0: brightness levels: 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 
36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 
88 90 92 94 96 98 100
acpivga0: connected output devices:
acpivga0:   0x0100: Ext. Monitor, head 0, bios detect
acpivga0:   0x0110 (acpiout0): LCD Panel, head 0, bios detect
acpivga0:   0x0200: TV, head 0
acpivga0:   0x0210: Unknown Output Device, head 0, bios detect
acpivga0:   0x0220: Unknown Output Device, head 0, bios detect
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
RMEM (PNP0C01) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1022 product 0x1510 (rev. 0x00)
vga0 at pci0 dev 1 function 0: vendor 0x1002 product 0x9802 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
hdaudio0 at pci0 dev 1 function 1: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 19
hdafg0 at hdaudio0: ATI R6xx HDMI
hdafg0: HDMI00 2ch: Digital Out [Jack]
hdafg0: 2ch/0ch 32000Hz 44100Hz 48000Hz PCM16 AC3
ppb0 at pci0 dev 4 function 0: vendor 0x1022 product 0x1512 (rev. 0x00)
ppb0: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ahcisata0 at pci0 dev 17 function 0: vendor 0x1002 product 0x4391 (rev. 0x40)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 4 ports, 32 slots, CAP 
0xf732ff23<SXS,PSC,SSC,PMD,SPM,ISS=0x3=Gen3,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 18
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controller, 5 ports each: ohci0
usb1 at ehci0: USB revision 2.0
ohci1 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 18
ohci1: OHCI version 1.0, legacy support
usb2 at ohci1: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 17
ehci1: dropped intr workaround enabled
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
ehci1: companion controller, 5 ports each: ohci1
usb3 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x42)
piixpm0: polling (SB800)
iic0 at piixpm0: I2C bus
ixpide0 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev. 
0x40)
ixpide0: I/O access disabled at device
hdaudio1 at pci0 dev 20 function 2: HD Audio Controller
hdaudio1: interrupting at ioapic0 pin 16
hdafg1 at hdaudio1: Realtek ALC892
hdafg1: DAC00 6ch: Speaker [Jack]
hdafg1: DAC01 2ch: HP Out [Jack]
hdafg1: DIG02 2ch: SPDIF Out [Jack]
hdafg1: ADC03 2ch: Line In [Jack], Mic In [Jack]
hdafg1: ADC04 2ch: Mic In [Jack]
hdafg1: 6ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 
PCM24 AC3
audio0 at hdafg1: full duplex, playback, capture, independent
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x40)
ppb1 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x40)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
ohci2 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb4 at ohci2: USB revision 1.0
ppb2 at pci0 dev 21 function 0: vendor 0x1002 product 0x43a0 (rev. 0x00)
ppb2: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 21 function 1: vendor 0x1002 product 0x43a1 (rev. 0x00)
ppb3: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci4 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 
0x06)
re0: interrupting at ioapic0 pin 17
re0: Ethernet address bc:5f:f4:9c:b3:be
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 4
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ohci3 at pci0 dev 22 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb5 at ohci3: USB revision 1.0
ehci2 at pci0 dev 22 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci2: interrupting at ioapic0 pin 17
ehci2: dropped intr workaround enabled
ehci2: BIOS has given up ownership
ehci2: EHCI version 1.0
ehci2: companion controller, 4 ports each: ohci3
usb6 at ehci2: USB revision 2.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1700 (rev. 0x43)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1701 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1702 (rev. 0x00)
pchb4 at pci0 dev 24 function 3: vendor 0x1022 product 0x1703 (rev. 0x00)
amdtemp0 at pchb4: AMD CPU Temperature Sensors (Family14h)
pchb5 at pci0 dev 24 function 4: vendor 0x1022 product 0x1704 (rev. 0x00)
pchb6 at pci0 dev 24 function 5: vendor 0x1022 product 0x1718 (rev. 0x00)
pchb7 at pci0 dev 24 function 6: vendor 0x1022 product 0x1716 (rev. 0x00)
pchb8 at pci0 dev 24 function 7: vendor 0x1022 product 0x1719 (rev. 0x00)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: C2: I/O, lat 100 us, pow     0 mW
acpicpu0: P0: FFH, lat   1 us, pow  7155 mW, 1600 MHz
acpicpu0: P1: FFH, lat   1 us, pow  4083 mW, 1280 MHz
acpicpu0: P2: FFH, lat   1 us, pow  1810 mW,  800 MHz
acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  88 %
acpicpu0: T2: I/O, lat   1 us, pow     0 mW,  76 %
acpicpu0: T3: I/O, lat   1 us, pow     0 mW,  64 %
acpicpu0: T4: I/O, lat   1 us, pow     0 mW,  52 %
acpicpu0: T5: I/O, lat   1 us, pow     0 mW,  40 %
acpicpu0: T6: I/O, lat   1 us, pow     0 mW,  28 %
acpicpu0: T7: I/O, lat   1 us, pow     0 mW,  16 %
acpicpu1 at cpu1: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1600055400 Hz quality 3000
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 5 ports with 5 removable, self powered
uhub1 at usb1: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 5 ports with 5 removable, self powered
uhub2 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
uhub3 at usb3: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 4 ports with 4 removable, self powered
uhub6 at usb6: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 4 ports with 4 removable, self powered
ahcisata0 port 0: device present, speed: 6.0Gb/s
ahcisata0 port 1: device present, speed: 3.0Gb/s
ahcisata0 port 2: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <KINGSTON SV300S37A60G>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 57241 MB, 116301 cyl, 16 head, 63 sec, 512 bytes/sect x 117231408 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
wd1 at atabus1 drive 0
wd1: <SAMSUNG HD103UJ>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd1(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
wd2 at atabus2 drive 0
wd2: <SAMSUNG HD103UJ>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd2(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
raid0: RAID Level 1
raid0: Components: /dev/wd1e /dev/wd2e
raid0: Total Sectors: 1953524992 (953869 MB)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)