Could not load wpi firmware

To: NetBSD/amd64 <port-amd64%NetBSD.org@localhost>
Subject: Could not load wpi firmware
From: Joel CARNAT <joel%carnat.net@localhost>
Date: Sat, 26 Jul 2008 12:38:18 +0200

Hello,

I can't get my XPS M1330's wpi interface working on NetBSD 4.99.70/amd64.

I already had the issue earlier this year and couldn't solve it.
So I stopped trying to use /amd64 hoping this would be solved by some
ACPI and/or other code upgrade. Since then I've been using NetBSD/i386
without special issues. A few days ago, I decided to give /amd64 a try
but it still fails getting wpi0 up. I installed OpenBSD 4.4-beta/amd64
and I don't have a single problem with wpi0 - it goes up straight away.

I tried using the firmware binary from OpenBSD on my NetBSD install but
this doesn't solve my problem. I tried upgrading/resetting the BIOS:
still fails. I tried using the physical switch to set
Wireless/Bluetooth/3G on/off. Stopping the laptop (remove battery & AC)
between reboots, booting with switch On and switching it Off/On and
vice-versa. There is no way to get the wpi0 interface up.

I tried the same NetBSD install (it's running on a USB stick) on other
system with same wireless chips and don't get issue. I tried Dell D430
and Lenovo R61. The issue really seems located on that particular XPS
laptop.

The hw.wpi0.radio parameter follows physical switch status.
The wpi0 never gets the "RUNNING" state.

Anyone has a Dell XPS M1330 working ?

Find attached informations about dmesg, ifconfig and sysctl.
I can provide OpenBSD informations (dmesg, sysctl, ...) too if required.

Any idea ?
TIA,
        Jo

### Upgrading to the latest BIOS update.

### Resetting BIOS defaults.

### Booting with switch set to 1

# ifconfig -a
wpi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        ssid ""
        powersave off
        address: 00:1b:77:b6:58:e6
        media: IEEE802.11 autoselect
        status: no network
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        address: 43:4f:c0:00:22:0d:8c:70
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33648
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3

# sysctl hw
hw.machine = amd64
hw.model = Intel 686-class
hw.ncpu = 2
hw.byteorder = 1234
hw.physmem = -10436608
hw.usermem = -11124736
hw.pagesize = 4096
hw.disknames = cd0 wd0 sd0 md0
hw.machine_arch = x86_64
hw.alignbytes = 7
hw.cnmagic = \x27\x02
hw.physmem64 = 4284530688
hw.usermem64 = 4283842560
hw.iostatnames = cd0 wd0 sd0 md0
hw.ncpuonline = 2
hw.ath.dwell = 200
hw.ath.calibrate = 30
hw.ath.outdoor = 1
hw.ath.countrycode = 0
hw.ath.regdomain = 0
hw.ath.debug = 0
hw.ath.rxbuf = 40
hw.ath.txbuf = 100
hw.ath.hal.version = 0.9.17.2
hw.ath.hal.dma_brt = 2
hw.ath.hal.sw_brt = 10
hw.ath.hal.swba_backoff = 0
hw.rtw.rfprog_fallback = 0
hw.rtw.host_rfio = 0
hw.firmware.path = 
/libdata/firmware:/usr/libdata/firmware:/usr/pkg/libdata/firmware:/usr/pkg/libdata
hw.bge.rx_lvl = 0
hw.fwohci.nocyclemaster = 0
hw.fwohci.phydma_enable = 1
hw.ieee1394if.try_bmr = 1
hw.ieee1394if.hold_count = 3
hw.ieee1394if.ieee1394_debug = 0
hw.fwmem.eui64_hi = 0
hw.fwmem.eui64_lo = 0
hw.fwmem.speed = 2
hw.fwmem.fwmem_debug = 0
hw.fwip.rx_queue_len = 256
hw.fwip.if_fwip_debug = 0
hw.sbp.auto_login = 1
hw.sbp.max_speed = -1
hw.sbp.exclusive_login = 1
hw.sbp.login_delay = 1000
hw.sbp.scan_delay = 500
hw.sbp.use_doorbell = 0
hw.sbp.tags = 0
hw.sbp.sbp_debug = 0
hw.acpi.root = 1031152
hw.acpi.supported_states = S0 S3 S4 S5 
hw.synaptics.up_down_emulation = 2
hw.synaptics.up_down_motion_delta = 1
hw.synaptics.gesture_move = 200
hw.synaptics.gesture_length = 20
hw.synaptics.edge_left = 1632
hw.synaptics.edge_right = 5312
hw.synaptics.edge_top = 4288
hw.synaptics.edge_bottom = 1568
hw.synaptics.edge_motion_delta = 32
hw.synaptics.finger_high = 35
hw.synaptics.finger_low = 20
hw.synaptics.two_fingers_emulation = 0
hw.synaptics.scale_x = 16
hw.synaptics.scale_y = 16
hw.synaptics.max_speed_x = 32
hw.synaptics.max_speed_y = 32
hw.synaptics.movement_threshold = 4
hw.wpi0.radio = 1
hw.ubt0.config = 0
hw.ubt0.alt_config = 6
hw.ubt0.sco_rxsize = 0
hw.ubt0.sco_txsize = 0

# dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.70 (GENERIC) #0: Tue Jul 22 12:09:30 PDT 2008
        
builds@wb28:/home/builds/ab/HEAD/amd64/200807220002Z-obj/home/builds/ab/HEAD/src/sys/arch/amd64/compile/GENERIC
total memory = 4086 MB
avail memory = 3946 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.4 @ 0xf71c0 (44 entries)
Dell Inc. XPS M1330                       
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1995MHz, id 0x6fa
cpu0: Enhanced SpeedStep (1388 mV) 2000 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 2200 2000 1800 1600 1400 
1200
cpu1 at mainbus0 apid 1: Intel 686-class, 1995MHz, id 0x6fa
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL  , M08    ,27d80708>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
pckbc1 at acpi0 (PS2M, PNP0F13): aux port
pckbc1: irq 12
pckbc2 at acpi0 (KBC, PNP0303): kbd port
pckbc2: io 0x60,0x64,0x62,0x66 irq 1
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43,0x50-0x53 irq 2
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61,0x63,0x65,0x67
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PBTN, PNP0C0C): ACPI Power Button
acpibut1 at acpi0 (SBTN, PNP0C0E): ACPI Sleep Button
acpiacad0 at acpi0 (AC, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: DP-LGC52, LION, DELL NX5117 1438
acpidalb0 at acpi0 (MBTN, PNP0C32-0): Direct Application Launch Button
AMW0 (pnp0c14) at acpi0 not configured
acpitz0 at acpi0 (THM): critical 99.0C, passive cooling
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pms0: Synaptics touchpad version 6.3
pms0: Palm detect, Multi-finger
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2a00 (rev. 0x0c)
agp0 at pchb0: detected 7676k stolen memory
agp0: aperture at 0xe0000000, size 0x20000000
vga0 at pci0 dev 2 function 0: vendor 0x8086 product 0x2a02 (rev. 0x0c)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
vendor 0x8086 product 0x2a03 (miscellaneous display, revision 0x0c) at pci0 dev 
2 function 1 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2834 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 20
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2835 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x283a (rev. 0x02)
ehci0: interrupting at ioapic0 pin 22
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 21
azalia0: host: 0x8086/0x284b (rev. 2), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x283f (rev. 0x02)
ppb0: disabling notification events
pci1 at ppb0 bus 11
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2841 (rev. 0x02)
ppb1: disabling notification events
pci2 at ppb1 bus 12
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci2 dev 0 function 0: vendor 0x8086 product 0x4222 (rev. 0x02)
wpi0: interrupting at ioapic0 pin 17
wpi0: MoW2, address 00:1b:77:b6:58:e6
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbps
ppb2 at pci0 dev 28 function 3: vendor 0x8086 product 0x2845 (rev. 0x02)
ppb2: disabling notification events
pci3 at ppb2 bus 13
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 5: vendor 0x8086 product 0x2849 (rev. 0x02)
ppb3: disabling notification events
pci4 at ppb3 bus 9
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x14e4 product 0x1713 (ethernet network, revision 0x02) at pci4 dev 0 
function 0 not configured
uhci2 at pci0 dev 29 function 0: vendor 0x8086 product 0x2830 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 20
usb3 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 1: vendor 0x8086 product 0x2831 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 21
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 2: vendor 0x8086 product 0x2832 (rev. 0x02)
uhci4: interrupting at ioapic0 pin 22
usb5 at uhci4: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x2836 (rev. 0x02)
ehci1: interrupting at ioapic0 pin 20
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3 uhci4
usb6 at ehci1: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xf2)
pci5 at ppb4 bus 3
pci5: i/o space, memory space enabled
fwohci0 at pci5 dev 1 function 0: vendor 0x1180 product 0x0832 (rev. 0x05)
fwohci0: interrupting at ioapic0 pin 19
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 43:4f:c0:00:22:0d:8c:70
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x1180 product 0x0822 (SD Host Controller system, interface 0x01, 
revision 0x22) at pci5 dev 1 function 1 not configured
vendor 0x1180 product 0x0843 (miscellaneous system, revision 0x12) at pci5 dev 
1 function 2 not configured
vendor 0x1180 product 0x0592 (miscellaneous system, revision 0x12) at pci5 dev 
1 function 3 not configured
vendor 0x1180 product 0x0852 (miscellaneous system, revision 0x12) at pci5 dev 
1 function 4 not configured
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x2815 (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801HBM IDE Controller (ICH8M) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x2829
ahcisata0: interrupting at ioapic0 pin 17
ahcisata0: AHCI revision 1.1, 3 ports, 32 command slots, features 0xe720e0c0
atabus1 at ahcisata0 channel 0
atabus2 at ahcisata0 channel 2
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x283e (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
isa0 at pcib0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1995146000 Hz quality 3000
acpiacad0: AC adapter offline.
azalia0: codec[0]: Sigmatel STAC9228X (rev. 2.1), HDA rev. 1.0
azalia0: codec[2]: 0x1095/0x1392 (rev. 0.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
atapibus0 at atabus0: 2 targets
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
cd0 at atapibus0 drive 0: <MATSHITA DVD+/-RW UJ-857G, , Z111> cdrom removable
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
ahcisata0 port 0: device present, speed: 3.0Gb/s
wd0 at atabus1 drive 0: <Hitachi HTS722020K9A300>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 186 GB, 387621 cyl, 16 head, 63 sec, 512 bytes/sect x 390721968 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
ahcisata0 port 2: PHY offline
umass0 at uhub6 port 1 configuration 1 interface 0
umass0: JetFlash Mass Storage Device, rev 2.00/1.41, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <JetFlash, TS1GJFV20, 8.07> disk removable
sd0: fabricating a geometry
sd0: 977 MB, 977 cyl, 64 head, 32 sec, 512 bytes/sect x 2002942 sectors
sd0: fabricating a geometry
uhub7 at uhub0 port 2: Broadcom BCM2045B2, class 9/0, rev 2.00/1.00, addr 2
uhub7: 3 ports with 0 removable, self powered
ugen0 at uhub6 port 6
ugen0: OmniVision Technologies, Inc. -2640-07.05.16.3 Laptop Integrated Webcam, 
rev 2.00/1.00, addr 3
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
ugen1 at uhub1 port 2
ugen1: Novatel Wireless Novatel Wireless HSDPA Modem, rev 1.10/0.00, addr 2
ubt0 at uhub7 port 1
ubt0: Broadcom Corp BCM2045, rev 2.00/1.00, addr 3
uhidev0 at uhub7 port 2 configuration 1 interface 0
uhidev0: Broadcom Corp product 0x4502, rev 2.00/1.00, addr 4, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub7 port 3 configuration 1 interface 0
uhidev1: Broadcom Corp product 0x4503, rev 2.00/1.00, addr 5, iclass 3/1
uhidev1: 125 report ids
ums0 at uhidev1 reportid 2: 3 buttons
wsmouse1 at ums0 mux 0
uhid0 at uhidev1 reportid 125: input=2, output=0, feature=0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

### Set the wireless switch set to 0

# dmesg
<SNIP>
uhub7: at uhub0 port 2 (addr 2) disconnected
ubt0: at uhub7 port 1 (addr 3) disconnected
ubt0: detached
uhidev0: at uhub7 port 2 (addr 4) disconnected
wskbd1: disconnecting from wsdisplay0
wskbd1: detached
ukbd0: detached
uhidev0: detached
uhidev1: at uhub7 port 3 (addr 5) disconnected
wsmouse1: detached
ums0: detached
uhid0: detached
uhidev1: detached
uhub7: detached

# ifconfig -a
wpi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        ssid ""
        powersave off
        address: 00:1b:77:b6:58:e6
        media: IEEE802.11 autoselect
        status: no network
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        address: 43:4f:c0:00:22:0d:8c:70
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33648
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3

# sysctl hw
hw.machine = amd64
hw.model = Intel 686-class
hw.ncpu = 2
hw.byteorder = 1234
hw.physmem = -10436608
hw.usermem = -11137024
hw.pagesize = 4096
hw.disknames = cd0 wd0 sd0 md0
hw.machine_arch = x86_64
hw.alignbytes = 7
hw.cnmagic = \x27\x02
hw.physmem64 = 4284530688
hw.usermem64 = 4283830272
hw.iostatnames = cd0 wd0 sd0 md0
hw.ncpuonline = 2
hw.ath.dwell = 200
hw.ath.calibrate = 30
hw.ath.outdoor = 1
hw.ath.countrycode = 0
hw.ath.regdomain = 0
hw.ath.debug = 0
hw.ath.rxbuf = 40
hw.ath.txbuf = 100
hw.ath.hal.version = 0.9.17.2
hw.ath.hal.dma_brt = 2
hw.ath.hal.sw_brt = 10
hw.ath.hal.swba_backoff = 0
hw.rtw.rfprog_fallback = 0
hw.rtw.host_rfio = 0
hw.firmware.path = 
/libdata/firmware:/usr/libdata/firmware:/usr/pkg/libdata/firmware:/usr/pkg/libdata
hw.bge.rx_lvl = 0
hw.fwohci.nocyclemaster = 0
hw.fwohci.phydma_enable = 1
hw.ieee1394if.try_bmr = 1
hw.ieee1394if.hold_count = 3
hw.ieee1394if.ieee1394_debug = 0
hw.fwmem.eui64_hi = 0
hw.fwmem.eui64_lo = 0
hw.fwmem.speed = 2
hw.fwmem.fwmem_debug = 0
hw.fwip.rx_queue_len = 256
hw.fwip.if_fwip_debug = 0
hw.sbp.auto_login = 1
hw.sbp.max_speed = -1
hw.sbp.exclusive_login = 1
hw.sbp.login_delay = 1000
hw.sbp.scan_delay = 500
hw.sbp.use_doorbell = 0
hw.sbp.tags = 0
hw.sbp.sbp_debug = 0
hw.acpi.root = 1031152
hw.acpi.supported_states = S0 S3 S4 S5 
hw.synaptics.up_down_emulation = 2
hw.synaptics.up_down_motion_delta = 1
hw.synaptics.gesture_move = 200
hw.synaptics.gesture_length = 20
hw.synaptics.edge_left = 1632
hw.synaptics.edge_right = 5312
hw.synaptics.edge_top = 4288
hw.synaptics.edge_bottom = 1568
hw.synaptics.edge_motion_delta = 32
hw.synaptics.finger_high = 35
hw.synaptics.finger_low = 20
hw.synaptics.two_fingers_emulation = 0
hw.synaptics.scale_x = 16
hw.synaptics.scale_y = 16
hw.synaptics.max_speed_x = 32
hw.synaptics.max_speed_y = 32
hw.synaptics.movement_threshold = 4
hw.wpi0.radio = 0

### Set the wireless switch set to 1

# dmesg
<SNIP>
uhub7 at uhub0 port 2: Broadcom BCM2045B2, class 9/0, rev 2.00/1.00, addr 2
uhub7: 3 ports with 0 removable, self powered
ubt0 at uhub7 port 1
ubt0: Broadcom Corp BCM2045, rev 2.00/1.00, addr 3
uhidev0 at uhub7 port 2 configuration 1 interface 0
uhidev0: Broadcom Corp product 0x4502, rev 2.00/1.00, addr 4, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub7 port 3 configuration 1 interface 0
uhidev1: Broadcom Corp product 0x4503, rev 2.00/1.00, addr 5, iclass 3/1
uhidev1: 125 report ids
ums0 at uhidev1 reportid 2: 3 buttons
wsmouse1 at ums0 mux 0
uhid0 at uhidev1 reportid 125: input=2, output=0, feature=0

# ifconfig -a
wpi0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        ssid ""
        powersave off
        address: 00:1b:77:b6:58:e6
        media: IEEE802.11 autoselect
        status: no network
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        address: 43:4f:c0:00:22:0d:8c:70
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33648
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3

# sysctl hw
hw.machine = amd64
hw.model = Intel 686-class
hw.ncpu = 2
hw.byteorder = 1234
hw.physmem = -10436608
hw.usermem = -11137024
hw.pagesize = 4096
hw.disknames = cd0 wd0 sd0 md0
hw.machine_arch = x86_64
hw.alignbytes = 7
hw.cnmagic = \x27\x02
hw.physmem64 = 4284530688
hw.usermem64 = 4283830272
hw.iostatnames = cd0 wd0 sd0 md0
hw.ncpuonline = 2
hw.ath.dwell = 200
hw.ath.calibrate = 30
hw.ath.outdoor = 1
hw.ath.countrycode = 0
hw.ath.regdomain = 0
hw.ath.debug = 0
hw.ath.rxbuf = 40
hw.ath.txbuf = 100
hw.ath.hal.version = 0.9.17.2
hw.ath.hal.dma_brt = 2
hw.ath.hal.sw_brt = 10
hw.ath.hal.swba_backoff = 0
hw.rtw.rfprog_fallback = 0
hw.rtw.host_rfio = 0
hw.firmware.path = 
/libdata/firmware:/usr/libdata/firmware:/usr/pkg/libdata/firmware:/usr/pkg/libdata
hw.bge.rx_lvl = 0
hw.fwohci.nocyclemaster = 0
hw.fwohci.phydma_enable = 1
hw.ieee1394if.try_bmr = 1
hw.ieee1394if.hold_count = 3
hw.ieee1394if.ieee1394_debug = 0
hw.fwmem.eui64_hi = 0
hw.fwmem.eui64_lo = 0
hw.fwmem.speed = 2
hw.fwmem.fwmem_debug = 0
hw.fwip.rx_queue_len = 256
hw.fwip.if_fwip_debug = 0
hw.sbp.auto_login = 1
hw.sbp.max_speed = -1
hw.sbp.exclusive_login = 1
hw.sbp.login_delay = 1000
hw.sbp.scan_delay = 500
hw.sbp.use_doorbell = 0
hw.sbp.tags = 0
hw.sbp.sbp_debug = 0
hw.acpi.root = 1031152
hw.acpi.supported_states = S0 S3 S4 S5 
hw.synaptics.up_down_emulation = 2
hw.synaptics.up_down_motion_delta = 1
hw.synaptics.gesture_move = 200
hw.synaptics.gesture_length = 20
hw.synaptics.edge_left = 1632
hw.synaptics.edge_right = 5312
hw.synaptics.edge_top = 4288
hw.synaptics.edge_bottom = 1568
hw.synaptics.edge_motion_delta = 32
hw.synaptics.finger_high = 35
hw.synaptics.finger_low = 20
hw.synaptics.two_fingers_emulation = 0
hw.synaptics.scale_x = 16
hw.synaptics.scale_y = 16
hw.synaptics.max_speed_x = 32
hw.synaptics.max_speed_y = 32
hw.synaptics.movement_threshold = 4
hw.wpi0.radio = 1
hw.ubt0.config = 0
hw.ubt0.alt_config = 6
hw.ubt0.sco_rxsize = 0
hw.ubt0.sco_txsize = 0

# ifconfig wpi0 up

# dmes
<SNIP>
wpi0: fatal firmware error
wpi0: fatal firmware error

Prev by Date: Re: Tyan K8WE (S2895) Status
Next by Date: Atheros releases BSD licensed drivers for new hardware...
Previous by Thread: Re: Re: Re: could not load wpi firmware
Next by Thread: Re: [ANNOUNCEMENT] The pkgsrc-2007Q4 Branch
Indexes:

Home | Main Index | Thread Index | Old Index