--Boundary-00=_nbnvDxZbCRWx0HD
Content-Type: text/plain;
  charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: inline

Hi,

I recently tried to install NetBSD 3.0 on my Athlon64 box (nForce4
chipset), and I stumbled across the same problems as others with my
SATA hard disk. Fortunately (thanks, guys ;-)) the archives of this
mailing list indicated several possible solutions :

=2D try NetBSD -current
=2D try disabling APIC support in BIOS
=2D try disabling unused SATA and PATA ports in BIOS

So I burnt a -current amd64 install CD (daily built 200601040000Z),
and I made a few tests the result of which I thought might be useful
to others. To test whether the drive works: I boot from the install
CD, I quit installation, I first try `fdisk wd0', and then I try to
mount a FAT32 partition and to copy large directories. I also recorded
the output of dmesg on an USB key before trying to access the drive.


* In my standard BIOS configuration, with APIC enabled and all PATA
  and SATA ports enabled, I get the following message when I try to
  access the hard drive (sometimes with different tc_bcount):

    viaide2:0:0: lost interrupt
                 type ata, tc_bcount: 0, tc_skip: 0

  Usually, I get the error message at the first attempt to read
  from the drive, or after a few attempts (fdisk wd0). This happens
  both in 3.0 and -current.

* When I take my standard BIOS configuration and just disable APIC,
  then the problem disappears (both in 3.0 and -current).

* When I take my standard BIOS configuration and just disable SATA
  ports 3 and 4 (there are two SATA controllers in the nForce4) then
  the problem disappears (both in 3.0 and -current).
  I also successfully installed from the 3.0 CD in this BIOS config.


Hardware : Athlon64 3200+ (Venice)
           Asus A8N-SLI Premium (nForce4 SLI), BIOS ver. 1009
           Hitachi T7K250 in SATA 3.0Gb/s mode, on SATA1 port
           DVD reader and writer as masters on both IDE channels


In case somebody is interested, I attach dmesg outputs for all three
tests with -current. The dmesg diffs between the three tests are the
same with 3.0. BTW, I was surprised to see that the IRQs were the
same with APIC enabled and disabled.

Gr=E9goire.

--Boundary-00=_nbnvDxZbCRWx0HD
Content-Type: text/plain;
  charset="us-ascii";
  name="dmesg-current-std-bios-with-sata34-disabled.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
	filename="dmesg-current-std-bios-with-sata34-disabled.txt"

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.15 (INSTALL) #0: Wed Jan  4 16:18:40 UTC 2006
	builds@b2.netbsd.org:/home/builds/ab/HEAD/amd64/200601040000Z-obj/home/builds/ab/HEAD/src/sys/arch/amd64/compile/INSTALL
total memory = 1023 MB
avail memory = 978 MB
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (OEM00000 PROD00000000)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 Processor 3200+, 2400.31 MHz
cpu0: features: e7dbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features: e7dbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features: e7dbfbff<FXSR,SSE,SSE2,LONG,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: calibrating local timer
cpu0: apic clock running at 240 MHz
cpu0: 8 page colors
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type PCI   
mpbios: bus 4 is type PCI   
mpbios: bus 5 is type PCI   
mpbios: bus 6 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x005e (miscellaneous memory, revision 0xa3) at pci0 dev 0 function 0 not configured
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x10de product 0x0050 (rev. 0xa3)
vendor 0x10de product 0x0052 (SMBus serial bus, revision 0xa2) at pci0 dev 1 function 1 not configured
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x005a (rev. 0xa2)
ohci0: interrupting at ioapic0 pin 3 (irq 3)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 10 ports with 10 removable, self powered
vendor 0x10de product 0x005b (USB serial bus, interface 0x20, revision 0xa3) at pci0 dev 2 function 1 not configured
viaide0 at pci0 dev 6 function 0
viaide0: NVIDIA nForce4 IDE Controller (rev. 0xf2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 8 function 0
viaide1: NVIDIA nForce4 Serial ATA Controller (rev. 0xf3)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
viaide1: using ioapic0 pin 5 (irq 5) for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
ppb0 at pci0 dev 9 function 0: vendor 0x10de product 0x005c (rev. 0xa2)
pci1 at ppb0 bus 5
pci1: i/o space, memory space enabled
vendor 0x1102 product 0x0004 (audio multimedia, revision 0x04) at pci1 dev 6 function 0 not configured
vendor 0x1102 product 0x7003 (miscellaneous input, revision 0x04) at pci1 dev 6 function 1 not configured
vendor 0x1102 product 0x4001 (Firewire serial bus, interface 0x10, revision 0x04) at pci1 dev 6 function 2 not configured
vendor 0x104c product 0x8023 (Firewire serial bus, interface 0x10) at pci1 dev 11 function 0 not configured
skc0 at pci1 dev 12 function 0: ioapic0 pin 10 (irq 10)
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:13:d4:49:ed:64
makphy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 11 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci2 at ppb1 bus 4
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 12 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 13 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 14 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci5 at ppb4 bus 1
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci5 dev 0 function 0: vendor 0x1002 product 0x554d (rev. 0x00)
vga0: WARNING: ignoring 64-bit BAR @ 0x10
vga0: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
vendor 0x1002 product 0x556d (miscellaneous display) at pci5 dev 0 function 1 not configured
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3
pchb3: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
ioapic0: enabling
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
md0: internal 5000 KB image area
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <PLEXTOR DVD-ROM PX-130A, , 1.02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus1 at atabus1: 2 targets
cd1 at atapibus1 drive 0: <HL-DT-ST DVDRAM GSA-4163B, K0D542N4014, A105> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse0 at ums0 mux 0
umass0 at uhub0 port 6 configuration 1 interface 0
umass0: Generic USB2.0 Card Reader, rev 2.00/1.6e, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 4 luns per target
sd0 at scsibus0 target 0 lun 0: <Generic, CF, 1.6E> disk removable
sd0: drive offline
sd1 at scsibus0 target 0 lun 1: <Generic, MS, 1.6E> disk removable
sd1: drive offline
sd2 at scsibus0 target 0 lun 2: <Generic, MMC/SD, 1.6E> disk removable
sd2: drive offline
sd3 at scsibus0 target 0 lun 3: <Generic, SM, 1.6E> disk removable
sd3: drive offline
wd0 at atabus2 drive 0: <HDT722525DLA380>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uhub1 at uhub0 port 10
uhub1: Generic USB Embedded Hub, class 9/0, rev 2.00/0.01, addr 4
uhub1: 1 port with 0 removable, self powered
umass1 at uhub1 port 1 configuration 1 interface 0
umass1: Generic USB Mass Storage Device, rev 2.00/0.01, addr 5
umass1: using ATAPI over Bulk-Only
atapibus2 at umass1: 2 targets
sd4 at atapibus2 drive 0: <Generic, USB Flash Disk, 1.00> disk removable
sd4: fabricating a geometry
sd4: 250 MB, 250 cyl, 64 head, 32 sec, 512 bytes/sect x 512000 sectors
sd0(umass0:0:0:0): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd1(umass0:0:0:1): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd2(umass0:0:0:2): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd3(umass0:0:0:3): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd4(umass1:0:0): no door lock
sd4: fabricating a geometry
boot device: fd0
root on md0a dumps on md0b
root file system type: ffs
warning: no /dev/console
sd4: fabricating a geometry
sd4: fabricating a geometry

--Boundary-00=_nbnvDxZbCRWx0HD
Content-Type: text/plain;
  charset="iso-8859-1";
  name="dmesg-current-std-bios.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
	filename="dmesg-current-std-bios.txt"

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.15 (INSTALL) #0: Wed Jan  4 16:18:40 UTC 2006
	builds@b2.netbsd.org:/home/builds/ab/HEAD/amd64/200601040000Z-obj/home/builds/ab/HEAD/src/sys/arch/amd64/compile/INSTALL
total memory = 1023 MB
avail memory = 978 MB
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (OEM00000 PROD00000000)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 Processor 3200+, 2400.31 MHz
cpu0: features: e7dbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features: e7dbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features: e7dbfbff<FXSR,SSE,SSE2,LONG,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: calibrating local timer
cpu0: apic clock running at 240 MHz
cpu0: 8 page colors
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type PCI   
mpbios: bus 4 is type PCI   
mpbios: bus 5 is type PCI   
mpbios: bus 6 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x005e (miscellaneous memory, revision 0xa3) at pci0 dev 0 function 0 not configured
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x10de product 0x0050 (rev. 0xa3)
vendor 0x10de product 0x0052 (SMBus serial bus, revision 0xa2) at pci0 dev 1 function 1 not configured
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x005a (rev. 0xa2)
ohci0: interrupting at ioapic0 pin 4 (irq 4)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 10 ports with 10 removable, self powered
vendor 0x10de product 0x005b (USB serial bus, interface 0x20, revision 0xa3) at pci0 dev 2 function 1 not configured
viaide0 at pci0 dev 6 function 0
viaide0: NVIDIA nForce4 IDE Controller (rev. 0xf2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 7 function 0
viaide1: NVIDIA nForce4 Serial ATA Controller (rev. 0xf3)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
viaide1: using ioapic0 pin 5 (irq 11) for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
viaide2 at pci0 dev 8 function 0
viaide2: NVIDIA nForce4 Serial ATA Controller (rev. 0xf3)
viaide2: bus-master DMA support present
viaide2: primary channel wired to native-PCI mode
viaide2: using ioapic0 pin 11 (irq 5) for native-PCI interrupt
atabus4 at viaide2 channel 0
viaide2: secondary channel wired to native-PCI mode
atabus5 at viaide2 channel 1
ppb0 at pci0 dev 9 function 0: vendor 0x10de product 0x005c (rev. 0xa2)
pci1 at ppb0 bus 5
pci1: i/o space, memory space enabled
vendor 0x1102 product 0x0004 (audio multimedia, revision 0x04) at pci1 dev 6 function 0 not configured
vendor 0x1102 product 0x7003 (miscellaneous input, revision 0x04) at pci1 dev 6 function 1 not configured
vendor 0x1102 product 0x4001 (Firewire serial bus, interface 0x10, revision 0x04) at pci1 dev 6 function 2 not configured
vendor 0x104c product 0x8023 (Firewire serial bus, interface 0x10) at pci1 dev 11 function 0 not configured
skc0 at pci1 dev 12 function 0: ioapic0 pin 12 (irq 12)
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:13:d4:49:ed:64
makphy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 11 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci2 at ppb1 bus 4
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 12 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 13 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 14 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci5 at ppb4 bus 1
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci5 dev 0 function 0: vendor 0x1002 product 0x554d (rev. 0x00)
vga0: WARNING: ignoring 64-bit BAR @ 0x10
vga0: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
vendor 0x1002 product 0x556d (miscellaneous display) at pci5 dev 0 function 1 not configured
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3
pchb3: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
ioapic0: enabling
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
md0: internal 5000 KB image area
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <PLEXTOR DVD-ROM PX-130A, , 1.02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus1 at atabus1: 2 targets
cd1 at atapibus1 drive 0: <HL-DT-ST DVDRAM GSA-4163B, K0D542N4014, A105> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse0 at ums0 mux 0
umass0 at uhub0 port 6 configuration 1 interface 0
umass0: Generic USB2.0 Card Reader, rev 2.00/1.6e, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 4 luns per target
sd0 at scsibus0 target 0 lun 0: <Generic, CF, 1.6E> disk removable
sd0: drive offline
sd1 at scsibus0 target 0 lun 1: <Generic, MS, 1.6E> disk removable
sd1: drive offline
sd2 at scsibus0 target 0 lun 2: <Generic, MMC/SD, 1.6E> disk removable
sd2: drive offline
sd3 at scsibus0 target 0 lun 3: <Generic, SM, 1.6E> disk removable
sd3: drive offline
wd0 at atabus4 drive 0: <HDT722525DLA380>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide2:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uhub1 at uhub0 port 10
uhub1: Generic USB Embedded Hub, class 9/0, rev 2.00/0.01, addr 4
uhub1: 1 port with 0 removable, self powered
umass1 at uhub1 port 1 configuration 1 interface 0
umass1: Generic USB Mass Storage Device, rev 2.00/0.01, addr 5
umass1: using ATAPI over Bulk-Only
atapibus2 at umass1: 2 targets
sd4 at atapibus2 drive 0: <Generic, USB Flash Disk, 1.00> disk removable
sd4: fabricating a geometry
sd4: 250 MB, 250 cyl, 64 head, 32 sec, 512 bytes/sect x 512000 sectors
sd0(umass0:0:0:0): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd1(umass0:0:0:1): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd2(umass0:0:0:2): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd3(umass0:0:0:3): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd4(umass1:0:0): no door lock
sd4: fabricating a geometry
boot device: fd0
root on md0a dumps on md0b
root file system type: ffs
warning: no /dev/console
sd4: fabricating a geometry
sd4: fabricating a geometry

--Boundary-00=_nbnvDxZbCRWx0HD
Content-Type: text/plain;
  charset="us-ascii";
  name="dmesg-current-std-bios-with-apic-disabled.txt"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
	filename="dmesg-current-std-bios-with-apic-disabled.txt"

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.15 (INSTALL) #0: Wed Jan  4 16:18:40 UTC 2006
	builds@b2.netbsd.org:/home/builds/ab/HEAD/amd64/200601040000Z-obj/home/builds/ab/HEAD/src/sys/arch/amd64/compile/INSTALL
total memory = 1023 MB
avail memory = 978 MB
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon(tm) 64 Processor 3200+, 2400.30 MHz
cpu0: features: e7dbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features: e7dbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features: e7dbfbff<FXSR,SSE,SSE2,LONG,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x005e (miscellaneous memory, revision 0xa3) at pci0 dev 0 function 0 not configured
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x10de product 0x0050 (rev. 0xa3)
vendor 0x10de product 0x0052 (SMBus serial bus, revision 0xa2) at pci0 dev 1 function 1 not configured
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x005a (rev. 0xa2)
ohci0: interrupting at irq 4
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 10 ports with 10 removable, self powered
vendor 0x10de product 0x005b (USB serial bus, interface 0x20, revision 0xa3) at pci0 dev 2 function 1 not configured
viaide0 at pci0 dev 6 function 0
viaide0: NVIDIA nForce4 IDE Controller (rev. 0xf2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 7 function 0
viaide1: NVIDIA nForce4 Serial ATA Controller (rev. 0xf3)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
viaide1: using irq 11 for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
viaide2 at pci0 dev 8 function 0
viaide2: NVIDIA nForce4 Serial ATA Controller (rev. 0xf3)
viaide2: bus-master DMA support present
viaide2: primary channel wired to native-PCI mode
viaide2: using irq 5 for native-PCI interrupt
atabus4 at viaide2 channel 0
viaide2: secondary channel wired to native-PCI mode
atabus5 at viaide2 channel 1
ppb0 at pci0 dev 9 function 0: vendor 0x10de product 0x005c (rev. 0xa2)
pci1 at ppb0 bus 5
pci1: i/o space, memory space enabled
vendor 0x1102 product 0x0004 (audio multimedia, revision 0x04) at pci1 dev 6 function 0 not configured
vendor 0x1102 product 0x7003 (miscellaneous input, revision 0x04) at pci1 dev 6 function 1 not configured
vendor 0x1102 product 0x4001 (Firewire serial bus, interface 0x10, revision 0x04) at pci1 dev 6 function 2 not configured
vendor 0x104c product 0x8023 (Firewire serial bus, interface 0x10) at pci1 dev 11 function 0 not configured
skc0 at pci1 dev 12 function 0: irq 12
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:13:d4:49:ed:64
makphy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb1 at pci0 dev 11 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci2 at ppb1 bus 4
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 12 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 13 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 14 function 0: vendor 0x10de product 0x005d (rev. 0xa3)
pci5 at ppb4 bus 1
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci5 dev 0 function 0: vendor 0x1002 product 0x554d (rev. 0x00)
vga0: WARNING: ignoring 64-bit BAR @ 0x10
vga0: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
vendor 0x1002 product 0x556d (miscellaneous display) at pci5 dev 0 function 1 not configured
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
pchb3 at pci0 dev 24 function 3
pchb3: vendor 0x1022 product 0x1103 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
md0: internal 5000 KB image area
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <PLEXTOR DVD-ROM PX-130A, , 1.02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus1 at atabus1: 2 targets
cd1 at atapibus1 drive 0: <HL-DT-ST DVDRAM GSA-4163B, K0D542N4014, A105> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: B16_b_02 USB-PS/2 Optical Mouse, rev 2.00/98.02, addr 2, iclass 3/1
ums0 at uhidev0: 8 buttons and Z dir.
wsmouse0 at ums0 mux 0
umass0 at uhub0 port 6 configuration 1 interface 0
umass0: Generic USB2.0 Card Reader, rev 2.00/1.6e, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 4 luns per target
sd0 at scsibus0 target 0 lun 0: <Generic, CF, 1.6E> disk removable
sd0: drive offline
sd1 at scsibus0 target 0 lun 1: <Generic, MS, 1.6E> disk removable
sd1: drive offline
sd2 at scsibus0 target 0 lun 2: <Generic, MMC/SD, 1.6E> disk removable
sd2: drive offline
sd3 at scsibus0 target 0 lun 3: <Generic, SM, 1.6E> disk removable
sd3: drive offline
wd0 at atabus4 drive 0: <HDT722525DLA380>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide2:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uhub1 at uhub0 port 10
uhub1: Generic USB Embedded Hub, class 9/0, rev 2.00/0.01, addr 4
uhub1: 1 port with 0 removable, self powered
umass1 at uhub1 port 1 configuration 1 interface 0
umass1: Generic USB Mass Storage Device, rev 2.00/0.01, addr 5
umass1: using ATAPI over Bulk-Only
atapibus2 at umass1: 2 targets
sd4 at atapibus2 drive 0: <Generic, USB Flash Disk, 1.00> disk removable
sd4: fabricating a geometry
sd4: 250 MB, 250 cyl, 64 head, 32 sec, 512 bytes/sect x 512000 sectors
sd0(umass0:0:0:0): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd1(umass0:0:0:1): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd2(umass0:0:0:2): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd3(umass0:0:0:3): not ready, data = 00 00 00 00 3a 00 00 00 00 00
sd4(umass1:0:0): no door lock
sd4: fabricating a geometry
boot device: fd0
root on md0a dumps on md0b
root file system type: ffs
warning: no /dev/console
sd4: fabricating a geometry
sd4: fabricating a geometry

--Boundary-00=_nbnvDxZbCRWx0HD--