Subject: Re: Who is booting Alpha AXP 150 (aka Jensen)
To: Andy V. Churaevsky <ulysses@tot.zp.ua>
From: Bill Collins <collinsw@speakeasy.org>
List: port-alpha
Date: 04/01/2002 12:17:20
I also have a Jensen exhibiting the same problem.  Has anyone resolved
this?  (If someone has, please post the solution.  I wouldn't be suprised
if someone else would want to know.)  Thanks in advance...

	 				Bill

On Tue, 25 Dec 2001, Andy V. Churaevsky wrote:
> I have:
> 
> 
> >>> show config
> DEC 2000 Model 300 AXP - ROM Version 2.2
> Copyright (c) 1993 Digital Equipment Corporation.
> 
> Alpha AXP SRM Firmware Version - 370
> VMS PAL X5.48/OSF PAL X1.35 - Built on 12-FEB-1996 13:08:14.13
> 
> Eisa Info       Devnam      Devstat
> ---------       ------      -------
>                 CPU         OK EV4 P3.0 6.6ns
>                 MEM         OK 64MB
>                 NVR         OK
>                 SCC         OK
>                 IT          OK
>                 KBD         OK
>                 LPT         OK
> 1
> 2
> 3
> 4
> 5 ADP0001       SCSI        OK
> 6
> >>> sh dev
> 
>   BOOTDEV      ADDR      DEVTYPE    RM/FX    DEVNAM      REV     NUMBYTES
>   -------      ----      -------    -----    ------      ---     --------
>   FD0          PC Floppy DISK       RM
>   SCSI Devices..
>   DKA0         A/0/0     DISK       FX       7345-SC     1761    345.84MB
>   DKA400       A/4/0     RODISK     RM       RRD44       2873    ......
>   HOST         A/7/0     PROC                AHA1742A    G.2
> 
> 
> 
> 
> >>> b -fl a dka400
> INIT-S-CPU...
> AUDIT_BOOT_STARTS ...
> AUDIT_CHECKSUM_GOOD
> AUDIT_LOAD_BEGINS
> AUDIT_LOAD_DONE
> 
> 
> NetBSD/alpha 1.5.2 ISO 9660 Primary Bootstrap
> Jumping to entry point...
> 
> NetBSD/alpha 1.5.2 Secondary Bootstrap, Revision 1.10
> (he@albatross.urc.uninett.no, Aug 17 23:50:47 MEST 2001)
> 
> VMS PAL rev: 0x100010530
> OSF PAL rev: 0x20123
> Switch to OSF PAL code succeeded.
> 
> Boot flags: A
> open netbsd: No such file or directory
> >>> b -fl a dka400
> INIT-S-CPU...
> AUDIT_BOOT_STARTS ...
> AUDIT_CHECKSUM_GOOD
> AUDIT_LOAD_BEGINS
> AUDIT_LOAD_DONE
> 
> 
> NetBSD/alpha 1.5.2 ISO 9660 Primary Bootstrap
> Jumping to entry point...
> 
> NetBSD/alpha 1.5.2 Secondary Bootstrap, Revision 1.10
> (he@albatross.urc.uninett.no, Aug 17 23:50:47 MEST 2001)
> 
> VMS PAL rev: 0x100010530
> OSF PAL rev: 0x20123
> Switch to OSF PAL code succeeded.
> 
> Boot flags: A
> open netbsd: No such file or directory
> open netbsd.gz: No such file or directory
> open netbsd.bak: No such file or directory
> open netbsd.bak.gz: No such file or directory
> open netbsd.old: No such file or directory
> open netbsd.old.gz: No such file or directory
> open onetbsd: No such file or directory
> open onetbsd.gz: No such file or directory
> 7781664+250080=0x7a9158
> 
> Entering netbsd.alpha at 0xfffffc00003010c0...
> [ netbsd ELF symbol table not valid ]
> [ no symbol table formats found ]
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 1.5.2 (INSTALL) #26: Sat Aug 18 10:04:15 MEST 2001
>     he@albatross.urc.uninett.no:/usr/src/sys/arch/alpha/compile/INSTALL
> DEC2000 model 300, 150MHz
> 8192 byte page size, 1 processor.
> total memory = 65536 KB
> (2048 KB reserved for PROM, 63488 KB used by NetBSD)
> avail memory = 51008 KB
> using 409 buffers containing 3272 KB of memory
> mainbus0 (root)
> cpu0 at mainbus0: ID 0 (primary), 21064-0 (pass 2 or 2.1)
> jensenio0 at mainbus0
> pckbc0 at jensenio0 port 0x60
> com0 at jensenio0 port 0x3f8: ns8250 or ns16450, no fifo
> com0: console
> com0: interrupting at vector 0x900
> com1 at jensenio0 port 0x2f8: ns8250 or ns16450, no fifo
> com1: interrupting at vector 0x920
> lpt0 at jensenio0 port 0x3bc
> lpt0: interrupting at eisa irq 1
> mcclock0 at jensenio0 port 0x170: mc146818 or compatible
> eisa0 at jensenio0
> ahb0 at eisa0 slot 2: Adaptec AHA-1742A SCSI
> ahb0: interrupting at eisa irq 12
> scsibus0 at ahb0: 8 targets, 8 luns per target
> isa0 at jensenio0
> fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
> fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
> After that it's stop and do nothing
> 
> Yes, i have all other standard device (aka CPQvideo, DE422, monitor, keyb..)
> but all remove.
> What's wrong?
> 
> 
>