Things are running much better now, although I can't quite autoboot yet,
since there appears to be an issue in recognizing the boot device.  This is
with 1.4, not 1.4.1.

Here are the boot messages ...


NetBSD 1.4 (GENERIC) #1: Sat May  8 11:37:01 PDT 1999
    ross@netbsd.org:/usr/src/sys/arch/alpha/compile/GENERIC
Digital AlphaPC 164SX 533 MHz, 531MHz
8192 byte page size, 1 processor.
real mem = 134217728 (1957888 reserved for PROM, 132259840 used by NetBSD)
avail mem = 112500736
using 1614 buffers containing 13221888 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), PCA56 (unknown minor type 2)
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
cia0: extended capabilities: 1<BWEN>
cia0: using BWX for PCI config access
pci0 at cia0 bus 0
pci0: i/o enabled, memory enabled
de0 at pci0 dev 5 function 0
de0: interrupting at eb164 irq 9
de0: SMC 21041 [10Mb/s] pass 1.1
de0: address 00:00:c0:f2:f7:bf
de0: enabling 10baseT port
sio0 at pci0 dev 8 function 0: Contaq Microsystems 82C693 PCI-ISA Bridge
(rev. 0x00)
pciide0 at pci0 dev 8 function 1: Contaq Microsystems CY82C693 IDE
Controller
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
atapibus0 at pciide0 channel 0
cd0 at atapibus0 drive 1: <MATSHITA CR-589, , GS0M> type 5 cdrom removable
cd0: 32-bits data port
cd0: drive supports PIO mode 4, DMA mode 2
wd0 at pciide0 channel 0 drive 0: <IBM-DTTA-351010>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 9671MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 19807200 sectors
wd0: 32-bits data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
cd0(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide1 at pci0 dev 8 function 2: Contaq Microsystems CY82C693 IDE
Controller
pciide1: device disabled (at device)
ohci0 at pci0 dev 8 function 3: Contaq Microsystems 82C693 PCI-ISA Bridge
(rev. 0x00)
ohci0: couldn't map interrupt
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pckbc0 at isa0 port 0x60-0x64
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
WARNING: can't figure what device matches "IDE 0 108 0 0 0 0 0"
root device:


Entering wd0 as the root device gets things going, though.  Where did NetBSD
find "IDE 0 108 0 0 0 0 0", and how can I deal with it?


Tom Haapanen
tomh@metrics.com