> From root@polaris.garbled.net Wed Feb 10 02:40:15 1999
> 
> On 10-Feb-99 Ken Wellsch spoke unto us all:
> #    I note the GENERIC kernel says that the BusLogic driver is untested.
> #  I'm using a 948 card without any troubles - if there are things I can do
> #  so you can consider it "tested" feel free to tell me!
> 
> You have a 948 working with a recent current??   I have a 958 that I can't get
> working to save my life.. I'm running the most recent snapshot still..

Here is a full boot log (kernel built from 990123 weekly tarballs).
I was just building GENERIC but this is from a modified "BABYLON":
(I've also connected a Plextor 12x and an old Quantum drive ~850Mb
at times to the bha and they worked without a hitch)

| NetBSD 1.3I (PC164SX) #0: Tue Feb  9 19:39:08 EST 1999
|     root@pc164sx:/usr/src/sys/arch/alpha/compile/PC164SX
| Digital AlphaPC 164SX 533 MHz, 531MHz
| 8192 byte page size, 1 processor.
| real mem = 67108864 (1957888 reserved for PROM, 65150976 used by NetBSD)
| avail mem = 55377920
| using 795 buffers containing 6512640 bytes of memory
| mainbus0 (root)
| cpu0 at mainbus0: ID 0 (primary), PCA56 (unknown minor type 2)
| cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 1
| cia0: extended capabilities: 1<BWEN>
| cia0: using BWX for PCI config access
| pci0 at cia0 bus 0
| pci0: i/o enabled, memory enabled
| bha0 at pci0 dev 5 function 0: BusLogic 9xxC SCSI
| bha0: interrupting at eb164 irq 9
| bha0: model BT-948, firmware 5.07B
| bha0: sync, parity
| bha0 targ 0: sync, offset 15, period 100nsec
| scsibus0 at bha0: 8 targets, 8 luns per target
| sd0 at scsibus0 targ 0 lun 0: <MICROP, 3243-19   1128RV, 28RV> SCSI2 0/direct fixed
| sd0: 4095MB, 3956 cyl, 19 head, 111 sec, 512 bytes/sect x 8388315 sectors
| sio0 at pci0 dev 8 function 0: Contaq Microsystems 82C693 PCI-ISA Bridge (rev. 0x00)
| pciide0 at pci0 dev 8 function 1: Contaq Microsystems CY82C693 IDE Controller
| pciide0: bus-master DMA support present
| pciide0: primary channel wired to compatibility mode
| wd0 at pciide0 channel 0 drive 0: <IBM-DHEA-38451>
| wd0: drive supports 16-sector pio transfers, lba addressing
| wd0: 8063MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 16514064 sectors
| wd0: 32-bits data port
| wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
| wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
| pciide1 at pci0 dev 8 function 2: Contaq Microsystems CY82C693 IDE Controller
| pciide1: pciide0: hardware does not support DMA
| pciide1: primary channel wired to compatibility mode
| atapibus0 at pciide1 channel 0
| cd0 at atapibus0 drive 1: <GCD-R580B, , 1.03> type 5 cdrom removable
| cd0: 32-bits data port
| cd0: drive supports PIO mode 3, DMA mode 1
| cd0(pciide1:0:1): using PIO mode 3
| Contaq Microsystems 82C693 PCI-ISA Bridge (USB serial bus, interface 0x10) at pci0 dev 8 function 3 not configured
| de0 at pci0 dev 9 function 0
| de0: interrupting at eb164 irq 8
| de0: DEC DE500-BA 21143 [10-100Mb/s] pass 3.0
| de0: address 00:00:f8:1a:2a:e0
| de0: enabling 10baseT port
| isa0 at sio0
| com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
| com0: console
| com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
| lpt0 at isa0 port 0x3bc-0x3bf irq 7
| pckbc0 at isa0 port 0x60-0x64
| pcppi0 at isa0 port 0x61
| spkr0 at pcppi0
| mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
| root device: wd0a
| dump device (default wd0b): 
| file system (default generic): 
| root on wd0a dumps on wd0b
| root file system type: ffs