Hello I have my sound(card?) integrated on my motherboard.  It is a Yamaha 724F (DS-1).  I cannot seem to get the drivers to work with it however.  Here is the dmesg output:

NetBSD 2.0_STABLE (BRUNO) #0: Mon Feb 21 09:02:25 EST 2005
	root@:/usr/src/sys/arch/i386/compile/BRUNO
total memory = 127 MB
avail memory = 120 MB
BIOS32 rev. 0 found at 0xfd790
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III (686-class), 548.77 MHz, id 0x673
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 512 KB 32B/line 4-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 32 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 0 function 0: 3Dfx Interactive Voodoo3 (rev. 0x01)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
piixide0 at pci0 dev 7 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev. 0x01)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge, revision 0x02) at pci0 dev 7 function 3 not configured
/* Soundboard info start */
yds0 at pci0 dev 12 function 0: Yamaha 724F (DS-1) Audio (rev. 0x03)
yds0: can't map memory space
/* Soundboard info end */
ex0 at pci0 dev 16 function 0: 3Com 3c905C-TX 10/100 Ethernet with mngmt (rev. 0x6c)
ex0: interrupting at irq 9
ex0: MAC address 00:50:da:2b:0b:91
bmtphy0 at ex0 phy 24: Broadcom 3c905C internal PHY, rev. 4
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: read port 0x203
ne0 at isapnp0 port 0x240/32 irq 3
ne0: NE2000 Ethernet
ne0: Ethernet address 00:40:05:f9:cc:81
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
IPsec: Initialized Security Association Processing.
atapibus0 at atabus0: 2 targets
sd0 at atapibus0 drive 1: <IOMEGA  ZIP 100       ATAPI, , 23.D> disk removable
sd0: drive offline
sd0: 32-bit data port
wd0 at atabus0 drive 0: <QUANTUM FIREBALL CR13.0A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 12416 MB, 25228 cyl, 16 head, 63 sec, 512 bytes/sect x 25429824 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
sd0(piixide0:0:1): using PIO mode 3
atapibus1 at atabus1: 2 targets
cd0 at atapibus1 drive 0: <ATAPI CD-R/RW DRIVE, , VER 12T> cdrom removable
cd0: 32-bit data port
piixide0:1:0: lost interrupt
	type: ata tc_bcount: 0 tc_skip: 0
cd0: drive supports PIO mode 4piixide0:1:0: lost interrupt
	type: ata tc_bcount: 0 tc_skip: 0
, DMA mode 2piixide0:1:0: lost interrupt
	type: ata tc_bcount: 0 tc_skip: 0
, Ultra-DMA mode 2 (Ultra/33)
wd1 at atabus1 drive 1: <Maxtor 32049H2>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 19541 MB, 39704 cyl, 16 head, 63 sec, 512 bytes/sect x 40021632 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
wd1(piixide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
sd0(piixide0:0:1):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(piixide0:0:1):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(piixide0:0:1):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

boot device: wd1
root on wd1a dumps on wd1b
root file system type: ffs
wsdisplay0: screen 1 added (80x40, vt100 emulation)
wsdisplay0: screen 2 added (80x40, vt100 emulation)
wsdisplay0: screen 3 added (80x40, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x40, vt100 emulation)


As you can see the yds driver says "yds0: can't map memory space".  I have no idea how to fix this problem, if anyone can help me out I'd greatly appreciate it.

Thanks.