Hi,

I'm having trouble with my new Zoom 3075 pcmcia modem.

The modem is recognized on boot and when inserted,

	com2 at pcmcia0 function 0: serial device
	com2: ns16550a, working fifo

and I can open the device,

	cu -l /dev/tty02 -s 9600
	Connected.

yet it refuses to echo back anything that I type (AT commands).  I also 
notice a delay (maybe 10 sec) between when I type the escape sequence 
to exit cu (~.) and when I get the shell prompt back.

Am I missing somthing obvious?  If not, can somebody please make 
suggestions for where to start tracking down and fixing the problem.  
The modem uses the Agere (Lucent) Venus chipset.

Thanks,

Sverre


Here's a complete set of boot messages:

NetBSD 1.6R (ABBOR: GENERIC-$Revision: 1.553 $) #28: Tue May 13 12:53:59 
MDT 2003
        toor@abbor.viewmark.com:/usr/src/sys/arch/i386/compile/ABBOR
total memory = 255 MB
avail memory = 233 MB
using 3296 buffers containing 13184 KB of memory
BIOS32 rev. 0 found at 0xfd82c
PCI BIOS rev. 2.1 found at 0xfd980
PCI IRQ Routing Table rev. 1.0 found at 0xfdf30, size 176 bytes (9 
entries)
PCI Interrupt Router at 000:07:0 (vendor 0x8086 product 0x122e)
pci_addr_fixup: 000:10:0 0x104c 0xac51 new address 0x10000000
pci_addr_fixup: 000:10:1 0x104c 0xac51 new address 0x10001000
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III (686-class), 547.64 MHz, id 0x683
cpu0: features 383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 383f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 383f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu0: L2 cache 256 KB 32b/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7190 (rev. 0x03)
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7191 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 0 function 0: vendor 0x1002 product 0x4c4d (rev. 0x64)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x8086 product 0x7110 (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) 
(rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IBM-DJSA-220>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 17301 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 35433216 
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA DVD-ROM SD-C2402, 7000008617, 1917> 
cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data 
transfers)
uhci0 at pci0 dev 7 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 10
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
vendor 0x8086 product 0x7113 (miscellaneous bridge, revision 0x03) at 
pci0 dev 7 function 3 not configured
cbb0 at pci0 dev 10 function 0: vendor 0x104c product 0xac51 (rev. 0x00)
cbb1 at pci0 dev 10 function 1: vendor 0x104c product 0xac51 (rev. 0x00)
ex0 at pci0 dev 11 function 0: 3Com 3c556 MiniPCI 10/100 Ethernet (rev. 
0x10)
ex0: interrupting at irq 10
ex0: MAC address 00:00:86:44:54:60
tqphy0 at ex0 phy 0: 78Q2120 10/100 media interface, rev. 11
tqphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vendor 0x10b7 product 0x1007 (miscellaneous communications, revision 
0x10) at pci0 dev 11 function 1 not configured
esa0 at pci0 dev 13 function 0: vendor 0x125d product 0x1998 (rev. 0x00)
esa0: interrupting at irq 5
esa0: SigmaTel STAC9721/23 codec; 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at esa0: full duplex, mmap, independent
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
cbb0: interrupting at irq 10
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0
pcmcia0 at cardslot0
cbb1: interrupting at irq 10
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3 device 0
pcmcia1 at cardslot1
apm0 at mainbus0: Power Management spec V1.2
wi0 at pcmcia1 function 0: Lucent Technologies, WaveLAN/IEEE, Version 
01.01
wi0: 802.11 address 00:02:2d:1f:3f:e8
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.10.1)
wi0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
com2 at pcmcia0 function 0: serial device
com2: ns16550a, working fifo
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x50, vt100 emulation)
wsdisplay0: screen 2 added (80x50, vt100 emulation)
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x50, vt100 emulation)