Re: install/59485: sysinst unusable on smaller framebuffer resolutions

["Ramiro Aceves via gnats" <gnats-admin%NetBSD.org@localhost>]

The following reply was made to PR install/59485; it has been noted by GNATS.

From: Ramiro Aceves <ea1abz%gmail.com@localhost>
To: gnats-bugs%netbsd.org@localhost, install-manager%netbsd.org@localhost,
 gnats-admin%netbsd.org@localhost, netbsd-bugs%netbsd.org@localhost
Cc: 
Subject: Re: install/59485: sysinst unusable on smaller framebuffer
 resolutions
Date: Mon, 13 Jul 2026 11:16:53 +0200

 El 25/6/25 a las 1:05, uwe%stderr.spb.ru@localhost escribió:
 >> Number:         59485
 >> Category:       install
 >> Synopsis:       sysinst unusable on smaller framebuffer resolutions
 >> Confidential:   no
 >> Severity:       serious
 >> Priority:       medium
 >> Responsible:    install-manager
 >> State:          open
 >> Class:          sw-bug
 >> Submitter-Id:   net
 >> Arrival-Date:   Tue Jun 24 23:05:00 +0000 2025
 >> Originator:     Valery Ushakov
 >> Release:        NetBSD 10.1
 >> Organization:
 >> Environment:
 >> Description:
 > I was trying to install netbsd on an old intel mac mini.  Since x86
 > doesn't have the usual comforts of a serial console, like most
 > civilized machines, I had to use a monitor.  I don't have much space
 > on my table, but luckily I have a cute little 10" monitor that can do
 > 1024x768, so I am using that when I need a monitor for something.
 > 
 > NetBSD install USB boots and attaches intelfb0 and uses it with the
 > 8x16 font for kernel messages.  When it comes to the userland though,
 > it switches to a font twice as large, b/c of proliferation of hi-res
 > displays, but at 1024x768 it's only 64x24 terminal and that is not
 > enough for larger sysinst menus (e.g. paritioning), so sysinst fails
 > eventually, when you reach one of those.
 > 
 >> How-To-Repeat:
 > Try to use sysinst on a lower resolution monitor.
 >> Fix:
 > May be hi-res workaround in the driver should not be applied if the
 > resulting terminal will be less than 80 columns?
 > 
 > One can always drop to the shell prompt and do
 > 
 >      wsconsctl -dw font=...
 > 
 > and use either that 8x16 font or may be use appropriately sized
 > Terminus, so that you get large enough characters, but still at least
 > 80 columns.  So it's not insurmountable for someone familiar with
 > NetBSD.  But potentially quite confusing to someone new.
 > 
 
 Hi,
 
 Just to share my experience.
 
 The Kingston 250 GB SSD in my little (and rather slow) Acer Aspire One (Atom 
 N455) died after just 3 years and 3 months of relatively light use (what a 
 crappy drive).
 
 I was updating to 2026Q1 under NetBSD 11.0_RC6 when the kernel started printing 
 lots of disk errors (in green messages), and the system became unresponsive. I 
 rebooted and ran fsck. I tried the update again, and before long the same errors 
 appeared. After another reboot, the SSD had completely died â?? even the BIOS 
 could no longer detect it.
 
 I tried to resurrect the drive using the power-cycle method, but after several 
 attempts I had no luck: one hour powered on with tape covering the data pins, 
 then power off for 30 seconds, and repeat... I do not know if it is a silly 
 thing, but I tried it.
 
 Since I don't think it makes sense to spend money on a new SSD (they cost about 
 twice as is cost before), I reinstalled the original hard drive that came with 
 the laptop.
 
 I booted the RC6 installer, and sysinst showed the same error about the large 
 font and the limited number of screen columns.
 
 I solved it with:
 
 wsconsctl -dw font=Boldface
 
 if I remember correctly.
 
 It's a bit tricky for newcomers. For someone trying NetBSD for the first time, 
 this could easily be the point where they give up if they aren't persistent enough.
 
 Thanks,
 Ramiro