Re: install/59621: kernel panic with Fujitsu Siemens Lifebook E Series

[d-ra <df4nx%gmx.net@localhost>]

Michael van Elst via gnats <gnats-admin%netbsd.org@localhost> wrote:
>  
>  Looks like another miss:
>  
>  Index: esm.c
...

Thanks for the patch :-)

Now the kernel boots, but rc.conf freezes while configuring the network
interface fxp0. I had to cycle via the power switch.

  \\-__,------,___.
   \\        __,---`  NetBSD/x86 BIOS Boot
    \\       `---,_.  Revision 5.11 (Mon Dec 16 13:08:11 UTC 2024)
     \\-,_____,.---`
      \\
       \\
        \\


     1. Boot normally
     2. Boot single user
     3. Drop to boot prompt

Choose an option; RETURN for default; SPACE to stop countdown.
Loading /var/db/entropy-file  
[   1.0000000] entropy: entering seed from bootloader with 256 bits of entropy
[   1.0000000] entropy: ready
[   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[   1.0000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[   1.0000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[   1.0000000]     2024
[   1.0000000]     The NetBSD Foundation, Inc.  All rights reserved.
[   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[   1.0000000]     The Regents of the University of California.  All rights reserved.

[   1.0000000] NetBSD 10.1 (GENERIC) #3: Mon Sep  1 14:45:53 CEST 2025
[   1.0000000] 	dra@sf.local:/usr/src/sys/arch/i386/compile/GENERIC
[   1.0000000] total memory = 255 MB
[   1.0000000] avail memory = 228 MB
[   1.0000040] mainbus0 (root)
[   1.0000040] ACPI: RSDP 0x00000000000F66B0 000014 (v00 FUJ   )
[   1.0000040] ACPI: RSDT 0x000000000FFEB691 000028 (v01 FUJ    BISCAYNE 01360000 FUJ  00001000)
[   1.0000040] ACPI: FACP 0x000000000FFEFB8C 000074 (v01 FUJ    BISCAYNE 01360000 FUJ  00001000)
[   1.0000040] ACPI: DSDT 0x000000000FFEB6B9 0044D3 (v01 FUJ    BISCAYNE 01360000 MSFT 01000007)
[   1.0000040] ACPI: FACS 0x000000000FFEFFC0 000040
[   1.0000040] ACPI: 1 ACPI AML tables successfully acquired and loaded
[   1.0000040] ACPI: BIOS is too old (19991130). Set acpi_force_load to use.
[   1.0000040] ACPI Error: Could not remove SCI handler (20221020/evmisc-316)
[   1.0000040] cpu0 at mainbus0
[   1.0000040] ACPI Error: AE_BAD_PARAMETER, Thread 3243113152 could not acquire Mutex [ACPI_MTX_Tables] (0x2) (20221020/utmutex-326)
[   1.0000040] ACPI Error: Mutex [ACPI_MTX_Tables] (0x2) is not acquired, cannot release (20221020/utmutex-367)
[   1.0000040] cpu0: Intel 686-class, 741MHz, id 0x686
[   1.0000040] cpu0: node 0, package 0, core 0, smt 0
[   1.0000040] pci0 at mainbus0 bus 0: configuration mode 1
[   1.0000040] pchb0 at pci0 dev 0 function 0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
[   1.0000040] agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
[   1.0000040] ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
[   1.0000040] pci1 at ppb0 bus 1
[   1.0000040] vga0 at pci1 dev 0 function 0: ATI Technologies Rage Mobility (rev. 0x64)
[   1.0000040] wsdisplay0 at vga0 kbdmux 1
[   1.0000040] drm at vga0 not configured
[   1.0000040] pcib0 at pci0 dev 7 function 0: Intel 82371AB (PIIX4) PCI-ISA Bridge (rev. 0x02)
[   1.0000040] piixide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
[   1.0000040] piixide0: primary channel interrupting at irq 14
[   1.0000040] atabus0 at piixide0 channel 0
[   1.0000040] piixide0: secondary channel interrupting at irq 15
[   1.0000040] atabus1 at piixide0 channel 1
[   1.0000040] uhci0 at pci0 dev 7 function 2: Intel 82371AB (PIIX4) USB Host Controller (rev. 0x01)
[   1.0000040] uhci0: interrupting at irq 9
[   1.0000040] usb0 at uhci0: USB revision 1.0
[   1.0000040] piixpm0 at pci0 dev 7 function 3: Intel 82371AB (PIIX4) Power Management Controller (rev. 0x03)
[   1.0006812] piixpm0: 24-bit timer
[   1.0006812] piixpm0: interrupting at SMI, 
[   1.0006812] iic0 at piixpm0 port 0: I2C bus
[   1.0006812] esm0 at pci0 dev 13 function 0: ESS Technology Maestro 2E PCI Audio Accelerator (rev. 0x10)
[   1.0006812] esm0: interrupting at irq 9
[   1.0006812] esm0: esm_read_codec() RW_DONE timed out.
[   1.0006812] esm0: will perform cold reset.
[   1.0006812] esm0: ac97: SigmaTel STAC9721/23 codec; 18 bit DAC, 18 bit ADC, SigmaTel 3D
[   1.0006812] audio0 at esm0: playback, capture, full duplex, independent
[   1.0006812] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[   1.0006812] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[   1.0006812] cbb0 at pci0 dev 15 function 0: Ricoh 5C476 PCI-CardBus Bridge (rev. 0x80)
[   1.0006812] cbb1 at pci0 dev 15 function 1: Ricoh 5C476 PCI-CardBus Bridge (rev. 0x80)
[   1.0006812] fxp0 at pci0 dev 16 function 0: i82559 Ethernet (rev. 0x08)
[   1.0006812] fxp0: interrupting at irq 9
[   1.0006812] fxp0: Ethernet address 00:e0:00:3a:65:9b
[   1.0006812] inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
[   1.0006812] inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[   1.0006812] isa0 at pcib0
[   1.0006812] lpt0 at isa0 port 0x378-0x37b irq 7
[   1.0006812] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[   1.0006812] com0: console
[   1.0006812] pckbc0 at isa0 port 0x60-0x64
[   1.0006812] pckbd0 at pckbc0 (kbd slot)
[   1.0006812] pckbc0: using irq 1 for kbd slot
[   1.0006812] wskbd0 at pckbd0 mux 1
[   1.0006812] pms0 at pckbc0 (aux slot)
[   1.0006812] pms0: ALPS PS/2 V2 pointing device
[   1.0006812] pckbc0: using irq 12 for aux slot
[   1.0006812] wsmouse0 at pms0 mux 0
[   1.0006812] attimer0 at isa0 port 0x40-0x43
[   1.0006812] pcppi0 at isa0 port 0x61
[   1.0006812] midi0 at pcppi0: PC speaker
[   1.0006812] sysbeep0 at pcppi0
[   1.0006812] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[   1.0006812] attimer0: attached to pcppi0
[   1.0006812] cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
[   1.0006812] cbb0: interrupting at irq 9
[   1.0006812] cardslot0 at cbb0
[   1.0006812] pcmcia0 at cardslot0
[   1.0006812] cbb1: secondary bus number uninitialized; try PCI_BUS_FIXUP
[   1.0006812] cbb1: interrupting at irq 9
[   1.0006812] cardslot1 at cbb1
[   1.0006812] pcmcia1 at cardslot1
[   1.4231282] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[   1.4966375] uhub0 at usb0: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[   4.6031742] wd0 at atabus0 drive 0
[   4.6461370] wd0: <FUJITSU MHT2040AT>
[   4.6908647] wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
[   4.8831794] atapibus0 at atabus1: 2 targets
[   4.9431825] cd0 at atapibus0 drive 0: <CD-224E, , 1.7A> cdrom removable
[   5.0242244] swwdog0: software watchdog initialized
[   5.1531827] WARNING: 2 errors while detecting hardware; check system log.
[   5.2372369] boot device: wd0
[   5.2715542] root on wd0a dumps on wd0b
[   5.3631865] root file system type: ffs
[   5.4075938] kern.module.path=/stand/i386/10.1/modules
Mon Sep  1 14:53:15 CEST 2025
Starting root file system check:
/dev/rwd0a: file system is clean; not checking
Setting sysctl variables:
ddb.onpanic: 1 -> 0
swapctl: setting dump device to /dev/wd0b
swapctl: adding /dev/wd0b as swap device at priority 0
Starting file system checks:
Loaded entropy from /var/db/entropy-file.
Waiting for entropy...done
Setting tty flags.
Starting network.
Hostname: p3.local
Configuring network interfaces: fxp0