NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: install/57826: NetBSD-10.0_RC2-i386-install.img installer keyboard does not work
El 9/1/24 a las 10:41, RVP escribió:
On Mon, 8 Jan 2024, Ramiro Aceves wrote:
I started installation but soon appear many errors on wd0 hard drive.
Installation was aborted with:
"Rewrite of MBR failed. I can`t continue"
There are something like 55 errors in those logs. Normally I would've
said that this HW was broken, but, as Linux runs fine on it, I have
to say, instead, that your have a _very_ quirky machine.
Hello RVP, many thanks for help!
Can you also show the output of this command (drop into the shell from
the installer):
$ sysctl kern.timecounters
that variable with that exact name did not exist. I find
kern.timecounter.choice, kern.timecounter.hardware and
kern.timecounter.timestepwarnings. I have recorded all kernel vars just
if helps. Please see below.
Then, can you try these and see if they help:
1. In BIOS,
a. turn on CSM (BIOS) mode (ie. disable UEFI)
b. turn off any `Fast Boot' setting
None of that settings is available at the BIOS screen, I think this old
machine does not now anything about UEFI.
BIOS settings are very simplyfied, I have never been able to enter in
any avanced BIOS settings in this old machine.
It is very odd because all the errors usually end in corrupting the
filesystem of the USB drive. fsck cannot repair the filesystem and had
to flash the USB drive several times.
If that doesn't help,
2. In the NetBSD bootloader, turn off ACPI: boot -2
That makes keyboard work! no errors! I have not tried to install until
your instructions say so.
I have recorded dmesg with ACPI on and with ACPI off. Also recorded
kernel vars in both situations.
Wait for instructions.
Regards.
********************** DMESG WITH ACPI ON ****************************
[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002,
2003,
[ 1.000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011,
2012, 2013,
[ 1.000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021,
2022, 2023,
[ 1.000000] 2024
[ 1.000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.000000] The Regents of the University of California. All
rights reserved.
[ 1.000000] NetBSD 10.0_RC2 (GENERIC) #0: Mon Jan 1 14:04:52 UTC 2024
[ 1.000000]
mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC
[ 1.000000] total memory = 2039 MB
[ 1.000000] avail memory = 1978 MB
[ 1.000000] timecounter: Timecounters tick every 10.000 msec
[ 1.000000] Kernelized RAIDframe activated
[ 1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz
quality 100
[ 1.000004] mainbus0 (root)
[ 1.000004] ACPI: RSDP 0x00000000000E5010 000014 (v00 INSYDE)
[ 1.000004] ACPI: RSDT 0x000000007F7FB2BB 000034 (v01 INSYDE
RSDT_000 00000100 ABCD 00010200)
[ 1.000004] ACPI: FACP 0x000000007F7FFB00 000074 (v01 INSYDE
FACP_000 00000100 0000 00010200)
[ 1.000004] ACPI: DSDT 0x000000007F7FB920 0041DE (v01 COMPAL DL7x
00000001 INTL 02002036)
[ 1.000004] ACPI: FACS 0x000000007F7FFFC0 000040
[ 1.000004] ACPI: APIC 0x000000007F7FFB90 000068 (v01 STUPID
MAPIC_00 30307830 ABCD 00010200)
[ 1.000004] ACPI: SSDT 0x000000007F7FB4C7 000277 (v01 PmRef Cpu0Ist
00003000 INTL 20030522)
[ 1.000004] ACPI: SSDT 0x000000007F7FB2EF 0001D8 (v01 PmRef Cpu0Cst
00003001 INTL 20030522)
[ 1.000004] ACPI: 3 ACPI AML tables successfully acquired and loaded
[ 1.000004] ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 0x20,
24 pins
[ 1.000004] cpu0 at mainbus0 apid 0
[ 1.000004] cpu0: Use lfence to serialize rdtsc
[ 1.000004] cpu0: Intel(R) Pentium(R) M processor 1.86GHz, id 0x6d8
[ 1.000004] cpu0: node 0, package 0, core 0, smt 0
[ 1.000004] acpi0 at mainbus0: Intel ACPICA 20221020
[ 1.000004] acpi0: X/RSDT: OemId <INSYDE,RSDT_000,00000100>, AslId
<ABCD,00010200>
[ 1.000004] acpi0: SCI interrupting at int 9
[ 1.000004] acpi0: fixed power button present
[ 1.000004] timecounter: Timecounter "ACPI-Fast" frequency 3579545
Hz quality 1000
[ 1.028342] acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
[ 1.028342] acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
[ 1.028342] acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
[ 1.028342] acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
[ 1.028342] acpivga0 at acpi0 (GFX0): ACPI Display Adapter
[ 1.028342] acpiout0 at acpivga0 (LCD, 0x0400): ACPI Display Output
Device
[ 1.028342] acpiout1 at acpivga0 (CRT1, 0x0100): ACPI Display Output
Device
[ 1.028342] acpiout2 at acpivga0 (DTV1, 0x0200): ACPI Display Output
Device
[ 1.028342] acpivga0: connected output devices:
[ 1.028342] acpivga0: 0x0100 (acpiout1): Ext. Monitor, head 0,
bios detect
[ 1.028342] acpivga0: 0x0400 (acpiout0): Unknown Output Device,
head 0, bios detect
[ 1.028342] acpivga0: 0x0200 (acpiout2): TV, head 0, bios detect
[ 1.028342] FWHD (INT0800) at acpi0 not configured
[ 1.028342] MATH (PNP0C04) at acpi0 not configured
[ 1.028342] attimer1 at acpi0 (TIMR, PNP0100): io
0x40-0x43,0x50-0x53 irq 0
[ 1.028342] acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
[ 1.028342] acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery
[ 1.028342] pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64
irq 1
[ 1.028342] pckbc2 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
[ 1.028342] apm0 at acpi0: Power Management spec V1.2
[ 1.028342] ACPI: Enabled 4 GPEs in block 00 to 1F
[ 1.028342] pckbd0 at pckbc1 (kbd slot)
[ 1.028342] pckbc1: using irq 1 for kbd slot
[ 1.028342] wskbd0 at pckbd0: console keyboard
[ 1.028342] autoconfiguration error: pckbc: aux echo error 1
[ 1.028342] autoconfiguration error: pckbc: cmd word write error
[ 1.028342] pci0 at mainbus0 bus 0: configuration mode 1
[ 1.028342] pci0: i/o space, memory space enabled, rd/line, rd/mult,
wr/inv ok
[ 1.028342] pchb0 at pci0 dev 0 function 0: Intel
82915PM/GM/GMS,82910GML Host Bridge (rev. 0x04)
[ 1.028342] agp0 at pchb0: i915-family chipset
[ 1.028342] agp0: detected 7932k stolen memory
[ 1.028342] agp0: aperture at 0xa0000000, size 0x10000000
[ 1.028342] i915drmkms0 at pci0 dev 2 function 0: Intel
82915GM/GMS,82910GML Integrated Graphics Device (rev. 0x04)
[ 1.028342] Intel 82915GM/GMS IGD Companion (miscellaneous display,
revision 0x04) at pci0 dev 2 function 1 not configured
[ 1.028342] uhci0 at pci0 dev 29 function 0: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.028342] uhci0: interrupting at ioapic0 pin 23
[ 1.028342] usb0 at uhci0: USB revision 1.0
[ 1.028342] uhci1 at pci0 dev 29 function 1: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.028342] uhci1: interrupting at ioapic0 pin 19
[ 1.028342] usb1 at uhci1: USB revision 1.0
[ 1.028342] uhci2 at pci0 dev 29 function 2: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.028342] uhci2: interrupting at ioapic0 pin 18
[ 1.028342] usb2 at uhci2: USB revision 1.0
[ 1.028342] uhci3 at pci0 dev 29 function 3: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.028342] uhci3: interrupting at ioapic0 pin 16
[ 1.028342] usb3 at uhci3: USB revision 1.0
[ 1.028342] ehci0 at pci0 dev 29 function 7: Intel 82801FB/FR USB
EHCI Controller (rev. 0x04)
[ 1.028342] ehci0: 64-bit DMA - limited
[ 1.028342] ehci0: interrupting at ioapic0 pin 23
[ 1.028342] ehci0: EHCI version 0.0
[ 1.028342] ehci0: wrong number of companions (0 != 4)
[ 1.028342] ehci0: Using DMA subregion for control data structures
[ 1.028342] ehci0: autoconfiguration error: reset timeout
[ 1.028342] ehci0: autoconfiguration error: init failed, error=5
[ 1.028342] ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI
Bridge (rev. 0xd4)
[ 1.028342] pci1 at ppb0 bus 1
[ 1.028342] pci1: i/o space, memory space enabled
[ 1.028342] fwohci0 at pci1 dev 0 function 0: VIA Technologies
VT6306 IEEE 1394 Host Controller (rev. 0x80)
[ 1.028342] fwohci0: interrupting at ioapic0 pin 20
[ 1.028342] fwohci0: OHCI version 1.0 (ROM=1)
[ 1.028342] fwohci0: No. of Isochronous channels is 4.
[ 1.028342] fwohci0: EUI64 00:02:3f:59:88:40:01:0f
[ 1.028342] fwohci0: Phy 1394a available S400, 2 ports.
[ 1.028342] fwohci0: Link S400, max_rec 512 bytes.
[ 1.028342] fwohci0: max_rec 512 -> 2048
[ 1.028342] ieee1394if0 at fwohci0: IEEE1394 bus
[ 1.028342] fwip0 at ieee1394if0: IP over IEEE1394
[ 1.028342] fwohci0: Initiate bus reset
[ 1.028342] re0 at pci1 dev 1 function 0: RealTek 8169/8110 Gigabit
Ethernet (rev. 0x10)
[ 1.028342] re0: interrupting at ioapic0 pin 21
[ 1.028342] re0: RTL8169/8110SB (0x1000)
[ 1.028342] re0: Ethernet address 00:0f:b0:93:6f:e1
[ 1.028342] re0: using 256 tx descriptors
[ 1.028342] rgephy0 at re0 phy 7: RTL8211B 1000BASE-T media interface
[ 1.028342] rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT, 1000baseT-FDX, auto
[ 1.028342] iwi0 at pci1 dev 2 function 0: Intel PRO/Wireless LAN
2200BG Mini-PCI Adapter (rev. 0x05)
[ 1.028342] iwi0: interrupting at ioapic0 pin 22
[ 1.028342] iwi0: 802.11 address 00:13:ce:6b:7d:01
[ 1.028342] cbb0 at pci1 dev 4 function 0: ENE Technology CB710
CardBus Controller (rev. 0x00)
[ 1.028342] ENE Technology product 0530 (flash memory) at pci1 dev 4
function 1 not configured
[ 1.028342] sdhc0 at pci1 dev 4 function 2: ENE Technology
CB712/714/810 PCI SD Card Reader Controller (rev. 0x00)
[ 1.028342] sdhc0: interrupting at ioapic0 pin 17
[ 1.028342] sdhc0: SDHC 1.0, rev 0, caps <01e021a1/00000000>, SDMA,
33000 kHz, HS 3.3V, 512 byte blocks
[ 1.028342] sdmmc0 at sdhc0 slot 0
[ 1.028342] cbb0: cacheline 0x8 lattimer 0x40
[ 1.028342] cbb0: bhlc 0x824008
[ 1.028342] cbb0: autoconfiguration error: secondary bus number
uninitialized; try PCI_BUS_FIXUP
[ 1.028342] cbb0: interrupting at ioapic0 pin 16
[ 1.028342] cardslot0 at cbb0
[ 1.028342] pcmcia0 at cardslot0
[ 1.028342] auich0 at pci0 dev 30 function 2: i82801FB (ICH6) AC-97
Audio
[ 1.028342] auich0: interrupting at ioapic0 pin 17
[ 1.028342] auich0: ac97: Avance Logic unknown (0x414c4752) codec;
headphone, 20 bit DAC, 18 bit ADC, no 3D stereo
[ 1.028342] auich0: ac97: ext id 0xa07<AC97_23,AMAP,SPDIF,DRA,VRA>
[ 1.028342] Intel 82801FB/FR AC'97 Modem Controller (modem
communications, revision 0x04) at pci0 dev 30 function 3 not configured
[ 1.028342] ichlpcib0 at pci0 dev 31 function 0: Intel 82801FBM
ICH6M LPC Interface Bridge (rev. 0x04)
[ 1.028342] timecounter: Timecounter "ichlpcib0" frequency 3579545
Hz quality 1000
[ 1.028342] ichlpcib0: 24-bit timer
[ 1.028342] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[ 1.028342] tco0: Min/Max interval 1/367 seconds
[ 1.028342] piixide0 at pci0 dev 31 function 1: Intel 82801FB IDE
Controller (ICH6) (rev. 0x04)
[ 1.028342] piixide0: bus-master DMA support present
[ 1.028342] piixide0: primary channel configured to compatibility mode
[ 1.028342] piixide0: primary channel interrupting at ioapic0 pin 14
[ 1.028342] atabus0 at piixide0 channel 0
[ 1.028342] piixide0: secondary channel configured to compatibility mode
[ 1.028342] piixide0: secondary channel interrupting at ioapic0 pin 15
[ 1.028342] atabus1 at piixide0 channel 1
[ 1.028342] ichsmb0 at pci0 dev 31 function 3: Intel 82801FB/FR
SMBus Controller (rev. 0x04)
[ 1.028342] ichsmb0: interrupting at ioapic0 pin 19
[ 1.028342] iic0 at ichsmb0: I2C bus
[ 1.028342] isa0 at ichlpcib0
[ 1.028342] pcppi0 at isa0 port 0x61
[ 1.028342] midi0 at pcppi0: PC speaker
[ 1.028342] sysbeep0 at pcppi0
[ 1.028342] attimer1: attached to pcppi0
[ 1.028342] acpicpu0 at cpu0: ACPI CPU
[ 1.028342] acpicpu0: C1: HLT, lat 0 us, pow 0 mW
[ 1.028342] acpicpu0: C2: I/O, lat 1 us, pow 0 mW
[ 1.028342] acpicpu0: C3: I/O, lat 85 us, pow 0 mW
[ 1.028342] acpicpu0: P0: I/O, lat 110 us, pow 27000 mW, 1867 MHz
[ 1.028342] acpicpu0: P1: I/O, lat 110 us, pow 23000 mW, 1600 MHz
[ 1.028342] acpicpu0: P2: I/O, lat 110 us, pow 20000 mW, 1333 MHz
[ 1.028342] acpicpu0: P3: I/O, lat 110 us, pow 17000 mW, 1067 MHz
[ 1.028342] acpicpu0: P4: I/O, lat 110 us, pow 13000 mW, 800 MHz
[ 1.028342] acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 %
[ 1.028342] acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 %
[ 1.028342] acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 %
[ 1.028342] acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 %
[ 1.028342] acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 %
[ 1.028342] acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 %
[ 1.028342] acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 %
[ 1.028342] acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 %
[ 1.028342] fwohci0: BUS reset
[ 1.028342] fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
[ 1.028342] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
[ 1.028342] ieee1394if0: bus manager 0
[ 1.028342] WARNING: system needs entropy for security; see entropy(7)
[ 1.028342] timecounter: Timecounter "clockinterrupt" frequency 100
Hz quality 0
[ 1.927199] auich0: measured ac97 link rate at 48000 Hz
[ 1.927452] audio0 at auich0: playback, capture, full duplex,
independent
[ 1.928405] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms)
for playback
[ 1.928567] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms)
for recording
[ 1.929133] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.929556] uhub0 at usb2: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.929778] uhub0: 2 ports with 2 removable, self powered
[ 1.929975] uhub1 at usb3: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.930228] uhub1: 2 ports with 2 removable, self powered
[ 1.930395] uhub2 at usb0: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.930648] uhub2: 2 ports with 2 removable, self powered
[ 1.930816] uhub3 at usb1: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.931080] uhub3: 2 ports with 2 removable, self powered
[ 1.931658] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.931912] acpiacad0: AC adapter online.
[ 1.932330] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.933258] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.933677] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.934434] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.935025] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.935698] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.936370] atapibus0 at atabus0: 2 targets
[ 1.937378] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.937884] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.938388] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.938810] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.939229] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.939566] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.939902] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.940239] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.940660] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.940996] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.941333] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.941753] acpicpu0: autoconfiguration error: failed to set
frequency to 1600 (err 35)
[ 1.942090] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.942511] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.942847] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.943269] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.943604] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.943941] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.944447] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.944782] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.946549] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.946886] acpicpu0: autoconfiguration error: failed to set
frequency to 1333 (err 35)
[ 1.947306] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.947643] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.947979] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.948316] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.948739] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.949073] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.949412] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.949831] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.950167] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.950504] acpicpu0: autoconfiguration error: failed to set
frequency to 1067 (err 35)
[ 1.950924] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.951261] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.951597] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.952019] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.952439] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.952776] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.953112] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.953532] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.953869] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.954206] acpicpu0: autoconfiguration error: failed to set
frequency to 800 (err 35)
[ 1.955637] IPsec: Initialized Security Association Processing.
[ 1.996357] uhidev0 at uhub0 port 1 configuration 1 interface 0
[ 1.996611] uhidev0: vendor 1997 (0x1997) mini keyboard (0x2433),
rev 1.10/1.10, addr 2, iclass 3/1
[ 2.008475] ukbd0 at uhidev0
[ 2.008641] wskbd1 at ukbd0 mux 1
[ 2.008980] uhidev1 at uhub0 port 1 configuration 1 interface 1
[ 2.009160] uhidev1: vendor 1997 (0x1997) mini keyboard (0x2433),
rev 1.10/1.10, addr 2, iclass 3/1
[ 2.014449] umass0 at uhub2 port 1 configuration 1 interface 0
[ 2.014620] umass0: vendor 13fe (0x13fe) USB DISK Pro (0x1f20), rev
2.00/1.10, addr 2
[ 2.014785] umass0: using SCSI over Bulk-Only
[ 2.019919] scsibus0 at umass0: 2 targets, 2 luns per target
[ 2.024712] autoconfiguration error: piixide0:0:1: lost interrupt
[ 2.024712] type: ata tc_bcount: 512 tc_skip: 0
[ 2.024879] wd0 at atabus0 drive 0
[ 2.030265] uhidev1: 3 report ids
[ 2.030517] ums0 at uhidev1 reportid 1: 5 buttons and Z dir
[ 2.030769] wsmouse0 at ums0 mux 0
[ 2.031024] uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
[ 2.031360] uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0
[ 2.031778] sd0 at scsibus0 target 0 lun 0: <, USB DISK Pro, PMAP>
disk removable
[ 2.046337] sd0: 7646 MB, 30584 cyl, 16 head, 32 sec, 512 bytes/sect
x 15659008 sectors
[ 2.098498] wd0: <IC25N080ATMR04-0>
[ 2.098598] wd0: drive supports 16-sector PIO transfers, LBA48
addressing
[ 2.098598] wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512
bytes/sect x 156301488 sectors
[ 2.121382] sd1 at scsibus0 target 0 lun 1: <, USB DISK Pro, PMAP>
disk removable
[ 2.143342] sd1: 1440 KB, 80 cyl, 2 head, 18 sec, 512 bytes/sect x
2880 sectors
[ 2.185073] piixide0:0:0: recal timed out
[ 2.185163] wd0d: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0
sn 0), xfer f5c, retry 0
[ 2.477106] waiting for devices: atabus0 atabus1 wd0
[ 2.537349] wd0: soft error (corrected) xfer f5c
[ 2.584467] wd0: 32-bit data port
[ 2.584716] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA
mode 5 (Ultra/100)
[ 2.585473] wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5
(Ultra/100) (using DMA)
[ 2.586736] swwdog0: software watchdog initialized
[ 2.958361] WARNING: 56 errors while detecting hardware; check
system log.
[ 2.958485] boot device: sd0
[ 2.958547] root on sd0a dumps on sd0b
[ 3.046367] root file system type: ffs
[ 3.066307] kern.module.path=/stand/i386/10.0/modules
[ 3.074638] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.074760] [drm] Driver supports precise vblank timestamp query.
[ 3.075060] i915drmkms0: interrupting at ioapic0 pin 16 (i915drmkms0)
[ 3.104588] [drm] Initialized overlay support.
[ 3.104757] [drm] Initialized i915 1.6.0 20200114 for i915drmkms0 on
minor 0
[ 3.121499] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.123603] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.136055] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.141271] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.142281] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.143290] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.165756] intelfb0 at i915drmkms0
[ 3.165923] [drm] DRM_I915_DEBUG enabled
[ 3.166059] [drm] DRM_I915_DEBUG_GEM enabled
[ 3.166175] intelfb0: framebuffer at 0xa0009000, size 1280x800,
depth 32, stride 5120
[ 3.455601] acpibat0: workqueue busy: updates stopped
[ 3.863994] wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100
emulation), using wskbd0
[ 3.868690] wsmux1: connecting to wsdisplay0
[ 3.868710] wskbd1: connecting to wsdisplay0
[ 3.903117] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.914391] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.931386] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.947877] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 3.957217] warning:
/usr/src/sys/external/bsd/drm2/dist/drm/drm_vblank.c:1206: vblank wait
timed out on crtc 0
[ 4.833991] entropy: best effort
********************** DMESG WITH ACPI OFF ****************************
[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002,
2003,
[ 1.000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011,
2012, 2013,
[ 1.000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021,
2022, 2023,
[ 1.000000] 2024
[ 1.000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.000000] The Regents of the University of California. All
rights reserved.
[ 1.000000] NetBSD 10.0_RC2 (GENERIC) #0: Mon Jan 1 14:04:52 UTC 2024
[ 1.000000]
mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC
[ 1.000000] total memory = 2039 MB
[ 1.000000] avail memory = 1978 MB
[ 1.000000] timecounter: Timecounters tick every 10.000 msec
[ 1.000000] Kernelized RAIDframe activated
[ 1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz
quality 100
[ 1.000004] mainbus0 (root)
[ 1.000004] cpu0 at mainbus0
[ 1.000004] ACPI Error: AE_BAD_PARAMETER, Thread 3242924096 could
not acquire Mutex [ACPI_MTX_Tables] (0x2) (20221020/utmutex-326)
[ 1.000004] cpu0: Use lfence to serialize rdtsc
[ 1.000004] cpu0: Intel(R) Pentium(R) M processor 1.86GHz, id 0x6d8
[ 1.000004] cpu0: node 0, package 0, core 0, smt 0
[ 1.000004] pci0 at mainbus0 bus 0: configuration mode 1
[ 1.000004] pci0: i/o space, memory space enabled, rd/line, rd/mult,
wr/inv ok
[ 1.000004] pchb0 at pci0 dev 0 function 0: Intel
82915PM/GM/GMS,82910GML Host Bridge (rev. 0x04)
[ 1.000004] agp0 at pchb0: i915-family chipset
[ 1.000004] agp0: detected 7932k stolen memory
[ 1.000004] agp0: aperture at 0xa0000000, size 0x10000000
[ 1.000004] i915drmkms0 at pci0 dev 2 function 0: Intel
82915GM/GMS,82910GML Integrated Graphics Device (rev. 0x04)
[ 1.000004] Intel 82915GM/GMS IGD Companion (miscellaneous display,
revision 0x04) at pci0 dev 2 function 1 not configured
[ 1.000004] uhci0 at pci0 dev 29 function 0: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.000004] uhci0: interrupting at irq 7
[ 1.000004] usb0 at uhci0: USB revision 1.0
[ 1.000004] uhci1 at pci0 dev 29 function 1: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.000004] uhci1: interrupting at irq 3
[ 1.000004] usb1 at uhci1: USB revision 1.0
[ 1.000004] uhci2 at pci0 dev 29 function 2: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.000004] uhci2: interrupting at irq 11
[ 1.000004] usb2 at uhci2: USB revision 1.0
[ 1.000004] uhci3 at pci0 dev 29 function 3: Intel 82801FB/FR USB
UHCI Controller (rev. 0x04)
[ 1.000004] uhci3: interrupting at irq 11
[ 1.000004] usb3 at uhci3: USB revision 1.0
[ 1.000004] ehci0 at pci0 dev 29 function 7: Intel 82801FB/FR USB
EHCI Controller (rev. 0x04)
[ 1.000004] ehci0: 64-bit DMA - limited
[ 1.000004] ehci0: interrupting at irq 7
[ 1.000004] ehci0: EHCI version 1.0
[ 1.000004] ehci0: 4 companion controllers, 2 ports each: uhci0
uhci1 uhci2 uhci3
[ 1.000004] ehci0: Using DMA subregion for control data structures
[ 1.000004] usb4 at ehci0: USB revision 2.0
[ 1.000004] ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI
Bridge (rev. 0xd4)
[ 1.000004] pci1 at ppb0 bus 1
[ 1.000004] pci1: i/o space, memory space enabled
[ 1.000004] fwohci0 at pci1 dev 0 function 0: VIA Technologies
VT6306 IEEE 1394 Host Controller (rev. 0x80)
[ 1.000004] fwohci0: interrupting at irq 10
[ 1.000004] fwohci0: OHCI version 1.0 (ROM=1)
[ 1.000004] fwohci0: No. of Isochronous channels is 4.
[ 1.000004] fwohci0: EUI64 00:02:3f:59:88:40:01:0f
[ 1.000004] fwohci0: Phy 1394a available S400, 2 ports.
[ 1.000004] fwohci0: Link S400, max_rec 512 bytes.
[ 1.000004] fwohci0: max_rec 512 -> 2048
[ 1.000004] ieee1394if0 at fwohci0: IEEE1394 bus
[ 1.000004] fwip0 at ieee1394if0: IP over IEEE1394
[ 1.000004] fwohci0: Initiate bus reset
[ 1.000004] re0 at pci1 dev 1 function 0: RealTek 8169/8110 Gigabit
Ethernet (rev. 0x10)
[ 1.000004] re0: interrupting at irq 11
[ 1.000004] re0: RTL8169/8110SB (0x1000)
[ 1.000004] re0: Ethernet address 00:0f:b0:93:6f:e1
[ 1.000004] re0: using 256 tx descriptors
[ 1.000004] rgephy0 at re0 phy 7: RTL8211B 1000BASE-T media interface
[ 1.000004] rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
1000baseT, 1000baseT-FDX, auto
[ 1.000004] iwi0 at pci1 dev 2 function 0: Intel PRO/Wireless LAN
2200BG Mini-PCI Adapter (rev. 0x05)
[ 1.000004] iwi0: interrupting at irq 11
[ 1.000004] iwi0: 802.11 address 00:13:ce:6b:7d:01
[ 1.000004] cbb0 at pci1 dev 4 function 0: ENE Technology CB710
CardBus Controller (rev. 0x00)
[ 1.000004] ENE Technology product 0530 (flash memory) at pci1 dev 4
function 1 not configured
[ 1.000004] sdhc0 at pci1 dev 4 function 2: ENE Technology
CB712/714/810 PCI SD Card Reader Controller (rev. 0x00)
[ 1.000004] sdhc0: interrupting at irq 5
[ 1.000004] sdhc0: SDHC 1.0, rev 0, caps <01e021a1/00000000>, SDMA,
33000 kHz, HS 3.3V, 512 byte blocks
[ 1.000004] sdmmc0 at sdhc0 slot 0
[ 1.000004] cbb0: cacheline 0x8 lattimer 0x40
[ 1.000004] cbb0: bhlc 0x824008
[ 1.000004] cbb0: autoconfiguration error: secondary bus number
uninitialized; try PCI_BUS_FIXUP
[ 1.000004] pci_intr_map: no mapping for pin A (line=ff)
[ 1.000004] cbb0: autoconfiguration error: couldn't map interrupt
[ 1.000004] cardslot0 at cbb0
[ 1.000004] pcmcia0 at cardslot0
[ 1.000004] auich0 at pci0 dev 30 function 2: i82801FB (ICH6) AC-97
Audio
[ 1.000004] auich0: interrupting at irq 5
[ 1.000004] auich0: ac97: Avance Logic unknown (0x414c4752) codec;
headphone, 20 bit DAC, 18 bit ADC, no 3D stereo
[ 1.000004] auich0: ac97: ext id 0xa07<AC97_23,AMAP,SPDIF,DRA,VRA>
[ 1.000004] Intel 82801FB/FR AC'97 Modem Controller (modem
communications, revision 0x04) at pci0 dev 30 function 3 not configured
[ 1.000004] ichlpcib0 at pci0 dev 31 function 0: Intel 82801FBM
ICH6M LPC Interface Bridge (rev. 0x04)
[ 1.000004] timecounter: Timecounter "ichlpcib0" frequency 3579545
Hz quality 1000
[ 1.005016] ichlpcib0: 24-bit timer
[ 1.005016] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[ 1.005016] tco0: Min/Max interval 1/367 seconds
[ 1.005016] piixide0 at pci0 dev 31 function 1: Intel 82801FB IDE
Controller (ICH6) (rev. 0x04)
[ 1.005016] piixide0: bus-master DMA support present
[ 1.005016] piixide0: primary channel configured to compatibility mode
[ 1.005016] piixide0: primary channel interrupting at irq 14
[ 1.005016] atabus0 at piixide0 channel 0
[ 1.005016] piixide0: secondary channel configured to compatibility mode
[ 1.005016] piixide0: secondary channel interrupting at irq 15
[ 1.005016] atabus1 at piixide0 channel 1
[ 1.005016] ichsmb0 at pci0 dev 31 function 3: Intel 82801FB/FR
SMBus Controller (rev. 0x04)
[ 1.005016] ichsmb0: interrupting at irq 3
[ 1.005016] iic0 at ichsmb0: I2C bus
[ 1.005016] isa0 at ichlpcib0
[ 1.005016] pckbc0 at isa0 port 0x60-0x64
[ 1.005016] pckbd0 at pckbc0 (kbd slot)
[ 1.005016] pckbc0: using irq 1 for kbd slot
[ 1.005016] wskbd0 at pckbd0: console keyboard
[ 1.005016] pms0 at pckbc0 (aux slot)
[ 1.005016] pms0: ALPS PS/2 V2 pointing device
[ 1.005016] pckbc0: using irq 12 for aux slot
[ 1.005016] wsmouse0 at pms0 mux 0
[ 1.005016] attimer0 at isa0 port 0x40-0x43
[ 1.005016] pcppi0 at isa0 port 0x61
[ 1.005016] midi0 at pcppi0: PC speaker
[ 1.005016] sysbeep0 at pcppi0
[ 1.005016] attimer0: attached to pcppi0
[ 1.005016] est0 at cpu0: Enhanced SpeedStep
[ 1.005016] fwohci0: BUS reset
[ 1.005016] fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
[ 1.005016] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
[ 1.005016] ieee1394if0: bus manager 0
[ 1.005016] WARNING: system needs entropy for security; see entropy(7)
[ 1.240990] timecounter: Timecounter "clockinterrupt" frequency 100
Hz quality 0
[ 1.573960] auich0: measured ac97 link rate at 48000 Hz
[ 1.573960] audio0 at auich0: playback, capture, full duplex,
independent
[ 1.573960] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms)
for playback
[ 1.573960] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms)
for recording
[ 1.573960] uhub0 at usb0: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.573960] uhub0: 2 ports with 2 removable, self powered
[ 1.573960] uhub1 at usb1: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.573960] uhub1: 2 ports with 2 removable, self powered
[ 1.573960] uhub2 at usb2: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.573960] uhub2: 2 ports with 2 removable, self powered
[ 1.573960] uhub3 at usb3: NetBSD (0x0000) UHCI root hub (0x0000),
class 9/0, rev 1.00/1.00, addr 1
[ 1.573960] uhub3: 2 ports with 2 removable, self powered
[ 1.573960] uhub4 at usb4: NetBSD (0x0000) EHCI root hub (0x0000),
class 9/0, rev 2.00/1.00, addr 1
[ 1.573960] uhub4: 8 ports with 8 removable, self powered
[ 1.583961] IPsec: Initialized Security Association Processing.
[ 1.593961] atapibus0 at atabus0: 2 targets
[ 1.673961] cd0 at atapibus0 drive 1: <TSSTcorpCD/DVDW TS-L632B,
95WK401090, TI33> cdrom removable
[ 1.683963] cd0: 32-bit data port
[ 1.683963] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA
mode 2 (Ultra/33)
[ 1.683963] wd0 at atabus0 drive 0
[ 1.693963] wd0: <IC25N080ATMR04-0>
[ 1.693963] wd0: drive supports 16-sector PIO transfers, LBA48
addressing
[ 1.693963] wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512
bytes/sect x 156301488 sectors
[ 2.123969] wd0: 32-bit data port
[ 2.123969] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA
mode 5 (Ultra/100)
[ 2.123969] wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5
(Ultra/100) (using DMA)
[ 2.123969] cd0(piixide0:0:1): using PIO mode 4, Ultra-DMA mode 2
(Ultra/33) (using DMA)
[ 2.643977] umass0 at uhub4 port 1 configuration 1 interface 0
[ 2.643977] umass0: vendor 13fe (0x13fe) USB DISK Pro (0x1f20), rev
2.00/1.10, addr 2
[ 2.643977] umass0: using SCSI over Bulk-Only
[ 2.643977] scsibus0 at umass0: 2 targets, 2 luns per target
[ 2.643977] sd0 at scsibus0 target 0 lun 0: <, USB DISK Pro, PMAP>
disk removable
[ 2.653977] sd0: 7646 MB, 30584 cyl, 16 head, 32 sec, 512 bytes/sect
x 15659008 sectors
[ 2.663977] sd1 at scsibus0 target 0 lun 1: <, USB DISK Pro, PMAP>
disk removable
[ 2.663977] sd1: 1440 KB, 80 cyl, 2 head, 18 sec, 512 bytes/sect x
2880 sectors
[ 3.293986] swwdog0: software watchdog initialized
[ 4.164000] WARNING: 2 errors while detecting hardware; check system
log.
[ 4.164000] boot device: sd0
[ 4.164000] root on sd0a dumps on sd0b
[ 4.174000] root file system type: ffs
[ 4.174000] kern.module.path=/stand/i386/10.0/modules
[ 4.174000] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.174000] [drm] Driver supports precise vblank timestamp query.
[ 4.174000] i915drmkms0: interrupting at irq 11 (i915drmkms0)
[ 4.204001] [drm] Initialized overlay support.
[ 4.204001] [drm] Initialized i915 1.6.0 20200114 for i915drmkms0 on
minor 0
[ 4.354011] intelfb0 at i915drmkms0
[ 4.354011] [drm] DRM_I915_DEBUG enabled
[ 4.354011] [drm] DRM_I915_DEBUG_GEM enabled
[ 4.354011] intelfb0: framebuffer at 0xa0009000, size 1280x800,
depth 32, stride 5120
[ 4.934013] wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100
emulation), using wskbd0
[ 4.934013] wsmux1: connecting to wsdisplay0
[ 5.094015] entropy: best effort
[ 5.114018] uhidev0 at uhub2 port 1 configuration 1 interface 0
[ 5.114018] uhidev0: vendor 1997 (0x1997) mini keyboard (0x2433),
rev 1.10/1.10, addr 2, iclass 3/1
[ 5.124015] ukbd0 at uhidev0
[ 5.124015] wskbd1 at ukbd0 mux 1
[ 5.124015] wskbd1: connecting to wsdisplay0
[ 5.134018] uhidev1 at uhub2 port 1 configuration 1 interface 1
[ 5.134018] uhidev1: vendor 1997 (0x1997) mini keyboard (0x2433),
rev 1.10/1.10, addr 2, iclass 3/1
[ 5.144019] uhidev1: 3 report ids
[ 5.144019] ums0 at uhidev1 reportid 1: 5 buttons and Z dir
[ 5.144019] wsmouse1 at ums0 mux 0
[ 5.144019] uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
[ 5.144019] uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0
************************** KERNEL VARS ACPI ON***************
netbsd-nuc# cat kernvars_ACPI_ON | grep timecount
kern.timecounter.choice = TSC(q=-100, f=15668420 Hz) clockinterrupt(q=0,
f=100 Hz) lapic(q=-100, f=1119000 Hz) ichlpcib0(q=1000, f=3579545 Hz)
ACPI-Fast(q=1000, f=3579545 Hz) i8254(q=100, f=1193182 Hz)
dummy(q=-1000000, f=1000000 Hz)
kern.timecounter.hardware = ACPI-Fast
kern.timecounter.timestepwarnings = 0
************************** KERNEL VARS ACPI OFF***************
netbsd-nuc# cat kernvars_ACPI_OFF | grep timecount
kern.timecounter.choice = TSC(q=-100, f=1895447880 Hz)
clockinterrupt(q=0, f=100 Hz) ichlpcib0(q=1000, f=3579545 Hz)
i8254(q=100, f=1193182 Hz) dummy(q=-1000000, f=1000000 Hz)
kern.timecounter.hardware = ichlpcib0
kern.timecounter.timestepwarnings = 0
Regards.
Ramiro.
You can, of course do both 1. and 2. together; but, try separately first.
-RVP
Home |
Main Index |
Thread Index |
Old Index