Re: kern/42314: IC Plus IP100x PHY support

[Andrius V <vezhlys%gmail.com@localhost>]

The following reply was made to PR kern/42314; it has been noted by GNATS.

From: Andrius V <vezhlys%gmail.com@localhost>
To: gnats-bugs%netbsd.org@localhost
Cc: msaitoh%netbsd.org@localhost, gnats-admin%netbsd.org@localhost, netbsd-bugs%netbsd.org@localhost, 
	tharada%oucrc.org@localhost
Subject: Re: kern/42314: IC Plus IP100x PHY support
Date: Thu, 14 Nov 2019 19:42:07 +0200

 Hi,
 
 Tested, didn't notice any regressions, auto-negotiation configures
 1000baseT full-duplex as expected (doesn't matter if on boot or using
 "ifconfig vge0 media auto" manually). Setting media type explicitly to
 1000baseT selects 100baseTX though (which is an improvement, since it
 was completely  failing with the original code).  From dmesg:
 
 [     1.050249] vge0 at pci4 dev 0 function 0: VIA VT612X Gigabit
 Ethernet (rev. 0x82)
 [     1.050249] vge0: interrupting at ioapic1 pin 12
 [     1.050249] vge0: Ethernet address xx:xx:xx:xx:xx:xx
 [     1.050249] ipgphy0 at vge0 phy 22: IP1001 10/100/1000 PHY, rev. 0
 [     1.050249] 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
 1000baseT, 1000baseT-FDX, auto
 
 ifconfig vge0 (auto)
 vge0: flags=0x8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
         capabilities=3f00<IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx>
         capabilities=3f00<UDP4CSUM_Rx,UDP4CSUM_Tx>
         enabled=0
         ec_capabilities=7<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
         ec_enabled=2<VLAN_HWTAGGING>
         address: xx:xx:xx:xx:xx:xx
         media: Ethernet autoselect (1000baseT
 full-duplex,flowcontrol,master,rxpause,txpause)
         status: active
         inet 192.168.1.10/24 broadcast 192.168.1.255 flags 0x0
         inet6 fe80::8c9e:c8a0:eb4b:731f%vge0/64 flags 0x0 scopeid 0x1
 ifconfig vge0 (1000baseT):
 vge0: flags=0x8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
         capabilities=3f00<IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx>
         capabilities=3f00<UDP4CSUM_Rx,UDP4CSUM_Tx>
         enabled=0
         ec_capabilities=7<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
         ec_enabled=2<VLAN_HWTAGGING>
         address: xx:xx:xx:xx:xx:xx
         media: Ethernet 1000baseT (100baseTX
 full-duplex,flowcontrol,rxpause,txpause)
         status: active
         inet 192.168.1.10/24 broadcast 192.168.1.255 flags 0x0
         inet6 fe80::8c9e:c8a0:eb4b:731f%vge0/64 flags 0x0 scopeid 0x1
 
 Regards,
 Andrius V
 
 
 On Thu, Nov 14, 2019 at 11:48 AM Andrius V <vezhlys%gmail.com@localhost> wrote:
 >
 > Hi,
 >
 > Sure, will do sometime today, once the changes will be synced with
 > fossil/git repos.
 >
 > On Thu, Nov 14, 2019 at 11:10 AM Masanobu SAITOH <msaitoh%execsw.org@localhost> wrote:
 > >
 > > The following reply was made to PR kern/42314; it has been noted by GNATS.
 > >
 > > From: Masanobu SAITOH <msaitoh%execsw.org@localhost>
 > > To: Andrius V <vezhlys%gmail.com@localhost>
 > > Cc: msaitoh%execsw.org@localhost, msaitoh%netbsd.org@localhost, gnats-admin%netbsd.org@localhost,
 > >  netbsd-bugs%netbsd.org@localhost, tharada%oucrc.org@localhost, gnats-bugs%netbsd.org@localhost
 > > Subject: Re: kern/42314: IC Plus IP100x PHY support
 > > Date: Thu, 14 Nov 2019 18:09:20 +0900
 > >
 > >  On 2019/10/09 0:38, Andrius V wrote:
 > >  > Hi,
 > >  >
 > >  >> It's merged!
 > >  >
 > >  > Thank you! Tested, working as expected.
 > >  >
 > >  >> Additional patch are also welcomed.
 > >  >
 > >  > Sure, if I will have something.
 > >  >
 > >  > Regards,
 > >  > Andrius V
 > >
 > >  Could you test with the latest ipgphy.c(rev. 1.4)?
 > >
 > >  Also please show me the output of the dmesg (both MAC and PHY).
 > >
 > >  Thanks in advance.
 > >
 > >  --
 > >  -----------------------------------------------
 > >                  SAITOH Masanobu (msaitoh%execsw.org@localhost
 > >                                   msaitoh%netbsd.org@localhost)
 > >