NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
port-i386/53894: "ehci_sync_hc: timed out" with ACPI/SMP enabled on eBox 3352DX3-AP
>Number: 53894
>Category: port-i386
>Synopsis: "ehci_sync_hc: timed out" with ACPI/SMP enabled on eBox 3352DX3-AP
>Confidential: no
>Severity: serious
>Priority: medium
>Responsible: port-i386-maintainer
>State: open
>Class: sw-bug
>Submitter-Id: net
>Arrival-Date: Sat Jan 19 22:30:00 +0000 2019
>Originator: Andrius V
>Release: 8.99.30
>Organization:
>Environment:
NetBSD vertexpc 8.99.30 NetBSD 8.99.30 (GENERIC) #0: Tue Jan 15 14:23:56 UTC 2019 mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC i386
>Description:
Recent testing showed that enabling IDE legacy mode in BIOS allows to boot into NetBSD on DM&P eBox 3352DX3-AP VortexDX3 based system with ACPI/SMP enabled (without legacy mode, IDE controller timeouts). However, there is one major caveat that USB devices fail to initialize in this case with repetitive "ehci_sync_hc: timed out" message in boot log, which eventually leads to next lines "uhub1: autoconfiguration error: device problem, disabling port 1", "uhub1: port 2, device disappeared after reset". However, USB devices initialize and work properly if system is booted without ACPI/SMP support (boot -12). Please see dmesg messages for comparison below. Only occasional disconnect/reconnect may happen while typing on keyboard in this case.
dmesg with ACPI/SMP:
NetBSD 8.99.30 (GENERIC) #0: Tue Jan 15 14:23:56 UTC 2019
mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC
total memory = 1983 MB
avail memory = 1929 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
efi: missing or invalid systbl
SMBIOS rev. 2.7 @ 0xfaf20 (43 entries)
RDC Semiconductor Co., Ltd. EMKORE (1.0 )
mainbus0 (root)
ACPI: RSDP 0x00000000000F7920 000024 (v03 ACPIAM)
ACPI: XSDT 0x000000007BFD0100 00004C (v01 R D C QA09 20151227 MSFT 00000097)
ACPI: FACP 0x000000007BFD0290 0000F4 (v04 R D C OEMFACP 20151227 MSFT 00000097)
ACPI: DSDT 0x000000007BFD05D0 005329 (v02 EMKORE EMKORE00 00000000 INTL 20060707)
ACPI: FACS 0x000000007BFDE000 000040
ACPI: APIC 0x000000007BFD0390 00005C (v02 R D C APIC1706 20151227 MSFT 00000097)
ACPI: MSDM 0x000000007BFD03F0 000055 (v03 R D C QA09 20151227 MSFT 00000097)
ACPI: SLIC 0x000000007BFD0450 000176 (v01 R D C QA09 20151227 MSFT 00000097)
ACPI: OEMB 0x000000007BFDE040 000082 (v01 R D C AMI_OEM 20151227 MSFT 00000097)
ACPI: 1 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0
cpu0: 2 page colors
cpu0: calibrating local timer
cpu0: apic clock running at 666 MHz
cpu0: Vortex86DX3, id 0x611
cpu0: package 0, core 0, smt 0
cpu1 at mainbus0 apid 1
cpu1: 2 page colors
cpu1: Vortex86DX3, id 0x611
cpu1: package 1, core 0, smt 0
acpi0 at mainbus0: Intel ACPICA 20181213
acpi0: X/RSDT: OemId <R D C , QA09 ,20151227>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
acpi0: ACPI-Safe 24-bit timer
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
COPR (PNP0C04) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
acpiacad0 at acpi0 (AC0, ACPI0003): ACPI AC Adapter
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpitz0 at acpi0 (THRM): cpu0
acpitz0: polling interval 30.0 seconds
acpitz0: levels: critical 92.0 C, passive 78.0 C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 17f3 product 6023 (rev. 0x02)
ppb0 at pci0 dev 1 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb0: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 2 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb1: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
pcib0 at pci0 dev 7 function 0: vendor 17f3 product 6035 (rev. 0x01)
pcib1 at pci0 dev 7 function 1: vendor 17f3 product 6035 (rev. 0x01)
vte0 at pci0 dev 8 function 0: vendor 17f3 product 6040 (rev. 0x00)
vte0: Ethernet address xx:xx:xx:xx:xx:xx
vte0: interrupting at ioapic0 pin 19
ukphy0 at vte0 phy 1: OUI 0xfcff2f, model 0x0005, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0 at pci0 dev 10 function 0: vendor 17f3 product 6060 (rev. 0x14)
ohci0: interrupting at ioapic0 pin 18
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 10 function 1: vendor 17f3 product 6061 (rev. 0x08)
ehci0: interrupting at ioapic0 pin 21
ehci0: EHCI version 1.0
ehci0: 1 companion controller, 4 ports: ohci0
usb1 at ehci0: USB revision 2.0
rdcide0 at pci0 dev 12 function 0: RDC R1012 IDE controller (rev. 0x02)
rdcide0: bus-master DMA support present
rdcide0: primary channel configured to compatibility mode
rdcide0: primary channel interrupting at ioapic0 pin 14
atabus0 at rdcide0 channel 0
rdcide0: secondary channel configured to compatibility mode
rdcide0: secondary channel ignored (disabled)
vga0 at pci0 dev 13 function 0: vendor 17f3 product 2015 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
hdaudio0 at pci0 dev 14 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 18
hdafg0 at hdaudio0 vendor 0x10EC product 0x0262 nid 0x01: vendor 10ec product 0262
hdafg0: DAC00 2ch: Speaker [Jack]
nid=14 [pin: Speaker (Green Jack)]
nid=0C [audio mixer] [source: dac, record]
nid=02 [audio output] [source: dac]
nid=0B [audio mixer] [source: record]
hdafg0: DIG01 2ch: Digital Out [Jack]
nid=1E [pin: Digital Out (Black Jack)]
nid=06 [audio output] [source: dac]
hdafg0: ADC02 2ch: Mic In [Jack]
nid=19 [pin: Mic In (Pink Jack)]
hdafg0: ADC03 2ch: Line In [Jack]
nid=1A [pin: Line In (Blue Jack)]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdafg0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
hdafg0: Latency: 128 milliseconds
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbdprobe: reset error 5
pmsprobe: reset error 5
isa at pcib1 not configured
acpicpu0 at cpu0: ACPI CPU
acpicpu0: HALT not supported?
acpicpu0: C1: HLT, lat 0 us, pow 0 mW
acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 %
acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 %
acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 %
acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 %
acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 %
acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 %
acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 %
acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 %
acpicpu0: id 1, lapic id 0, cap 0x0000, flags 0x00100c25
acpicpu1 at cpu1: ACPI CPU
acpicpu1: HALT not supported?
acpicpu1: id 2, lapic id 1, cap 0x0000, flags 0x00000c21
Initializing SSP: ac3b5c83 62fd8be 75262144 3cdb1f14 80cf06f8 cb42734a 48c375bf 1af02484
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
cpu1: TSC skew=3 drift=-5
cpu1: running
TSC not known invariant on this CPU
acpiacad0: AC adapter online.
acpiacad0: AC adapter connected
acpicpu1: ACPI CPUs started
uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb1: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
IPsec: Initialized Security Association Processing.
wd0 at atabus0 drive 0
wd0: <SS16G D0 RDC SD-IDE HOST CONTROLLER>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 15193 MB, 30869 cyl, 16 head, 63 sec, 512 bytes/sect x 31116288 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(rdcide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
ehci_sync_hc: timed out
uhub1: autoconfiguration error: device problem, disabling port 1
ehci0: handing over low speed device on port 2 to ohci0
uhub1: port 2, device disappeared after reset
ehci0: handing over full speed device on port 3 to ohci0
uhub1: port 3, device disappeared after reset
Searching for RAID components...
WARNING: 1 error while detecting hardware; check system log.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/i386/8.99.30/modules
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
dmesg with ACPI/SMP disabled:
NetBSD 8.99.30 (GENERIC) #0: Tue Jan 15 14:23:56 UTC 2019
mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/i386/compile/GENERIC
total memory = 1983 MB
avail memory = 1929 MB
rnd: seeded with 128 bits
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
RDC Semiconductor Co., Ltd. EMKORE (1.0 )
mainbus0 (root)
cpu0 at mainbus0
cpu0: Vortex86DX3, id 0x611
cpu0: package 0, core 0, smt 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 17f3 product 6023 (rev. 0x02)
ppb0 at pci0 dev 1 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb0: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 2 function 0: vendor 17f3 product 1031 (rev. 0x01)
ppb1: PCI Express capability version 1 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
pcib0 at pci0 dev 7 function 0: vendor 17f3 product 6035 (rev. 0x01)
pcib1 at pci0 dev 7 function 1: vendor 17f3 product 6035 (rev. 0x01)
vte0 at pci0 dev 8 function 0: vendor 17f3 product 6040 (rev. 0x00)
vte0: Ethernet address xx:xx:xx:xx:xx:xx
vte0: interrupting at irq 5
ukphy0 at vte0 phy 1: OUI 0xfcff2f, model 0x0005, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0 at pci0 dev 10 function 0: vendor 17f3 product 6060 (rev. 0x14)
ohci0: interrupting at irq 15
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 10 function 1: vendor 17f3 product 6061 (rev. 0x08)
ehci0: interrupting at irq 7
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: 1 companion controller, 4 ports: ohci0
usb1 at ehci0: USB revision 2.0
rdcide0 at pci0 dev 12 function 0: RDC R1012 IDE controller (rev. 0x02)
rdcide0: bus-master DMA support present
rdcide0: primary channel configured to compatibility mode
rdcide0: primary channel interrupting at irq 14
atabus0 at rdcide0 channel 0
rdcide0: secondary channel configured to compatibility mode
rdcide0: secondary channel ignored (disabled)
vga0 at pci0 dev 13 function 0: vendor 17f3 product 2015 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
hdaudio0 at pci0 dev 14 function 0: HD Audio Controller
hdaudio0: interrupting at irq 15
hdafg0 at hdaudio0: vendor 10ec product 0262
hdafg0: DAC00 2ch: Speaker [Jack]
hdafg0: DIG01 2ch: Digital Out [Jack]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: ADC03 2ch: Line In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdafg0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
hdafg0: Latency: 128 milliseconds
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer0: attached to pcppi0
isa at pcib1 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: NetBSD (0000) OHCI root hub (0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
uhub1 at usb1: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
IPsec: Initialized Security Association Processing.
axen0 at uhub1 port 1
axen0: D-Link Elec. Corp. (0x2001) D-Link DUB-1312 (0x4a00), rev 2.10/1.00, addr 2
axen0: AX88179
axen0: Ethernet address xx:xx:xx:xx:xx:xx
rgephy0 at axen0 phy 3: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 5
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
ehci0: handing over low speed device on port 2 to ohci0
wd0 at atabus0 drive 0
wd0: <SS16G D0 RDC SD-IDE HOST CONTROLLER>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 15193 MB, 30869 cyl, 16 head, 63 sec, 512 bytes/sect x 31116288 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(rdcide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
ehci0: handing over full speed device on port 3 to ohci0
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/i386/8.99.30/modules
WARNING: clock gained 2 days
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: USB (0x1c4f) USB Keykoard (0x02), rev 1.10/1.10, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 Variable keys, 6 Array codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1
uhidev1: USB (0x1c4f) USB Keykoard (0x02), rev 1.10/1.10, addr 2, iclass 3/0
uhidev1: 2 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
uchcom0 at uhub0 port 3
uchcom0: QinHeng Electronics (0x1a86) USB2.0-Ser! (0x7523), rev 1.10/2.54, addr 3
ucom0 at uchcom0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
>How-To-Repeat:
Boot machine with ACPI/SMP enabled
>Fix:
N/A. Workaround is to boot without ACPI/SMP enabled.
Home |
Main Index |
Thread Index |
Old Index