NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
kern/50030: amd64/7.0_RC1 ahcisata fails to attach drive
>Number: 50030
>Category: kern
>Synopsis: amd64/7.0_RC1 ahcisata fails to attach drive
>Confidential: no
>Severity: serious
>Priority: low
>Responsible: kern-bug-people
>State: open
>Class: sw-bug
>Submitter-Id: net
>Arrival-Date: Sat Jul 04 06:30:00 +0000 2015
>Originator: Tetsuya Isaki
>Release: NetBSD-7.0_RC1
>Organization:
>Environment:
NetBSD 7.0_RC1 amd64
>Description:
amd64/7.0_RC1 ahcisata fails to attach drive
I tried to upgrade my PC from 6.1.4 to 7.0_RC1 but
INSTALL kernel could not attach wd{1,2} at ahcisata
with the error message:
------
ahcisata0 channel 1: clearing WDCTL_RST failed for drive 0
ahcisata0 channel 2: clearing WDCTL_RST failed for drive 0
------
7.0_RC1's kernel config is INSTALL (untouched).
6.1.4's kernel config is just GENERIC + "options FFS_EI".
Here is 7.0_RC1's dmesg. wd1 and wd2 failed.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.0_RC1 (GENERIC) #4: Thu Jul 2 03:28:54 JST 2015
isaki@nao.XXXXX:/var/obj/7/amd64/obj/sys/arch/amd64/compile/GENERIC
total memory = 4094 MB
avail memory = 3957 MB
kern.module.path=/stand/amd64/7.0/modules
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
FUJITSU-SV PRIMERGY ( )
mainbus0 (root)
ACPI: RSDP 0xf7f50 000024 (v02 PTLTD )
ACPI: XSDT 0x7fec4685 0000A4 (v01 PTLTD ? XSDT 00060000 LTP 00000000)
ACPI: FACP 0x7fec824d 0000F4 (v03 FSC D2679/B1 00060000 000F4240)
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm1aControlBlock: 16/32 (20131218/tbfadt-634)
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Pm2ControlBlock: 8/32 (20131218/tbfadt-634)
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/PmTimerBlock: 32/24 (20131218/tbfadt-634)
ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20131218/tbfadt-634)
ACPI BIOS Warning (bug): Invalid length for FADT/Pm1aControlBlock: 32, using default 16 (20131218/tbfadt-716)
ACPI BIOS Warning (bug): Invalid length for FADT/Pm2ControlBlock: 32, using default 8 (20131218/tbfadt-716)
ACPI BIOS Warning (bug): Invalid length for FADT/PmTimerBlock: 24, using default 32 (20131218/tbfadt-716)
ACPI: DSDT 0x7fec4729 003AB0 (v01 FSC D2679 00060000 MSFT 03000001)
ACPI: FACS 0x7fecbfc0 000040
ACPI: TCPA 0x7fec8341 000032 (v01 Phoeni x 00060000 TL 00000000)
ACPI: EINJ 0x7fec8373 0001B0 (v01 PTL WHEAPTL 00060000 PTL 00000001)
ACPI: HEST 0x7fec8523 000268 (v01 PTL WHEAPTL 00060000 PTL 00000001)
ACPI: BERT 0x7fec878b 000030 (v01 PTL WHEAPTL 00060000 PTL 00000001)
ACPI: SSDT 0x7fec87bb 0000E1 (v01 wheaos wheaosc 00060000 INTL 20050624)
ACPI: ERST 0x7fec889c 000270 (v01 PTL WHEAPTL 00060000 PTL 00000001)
ACPI: SSDT 0x7fec8b0c 0000D8 (v01 FSC CST_PR00 00060000 CSF 00000001)
ACPI: SSDT 0x7fec8be4 0000D8 (v01 FSC CST_PR01 00060000 CSF 00000001)
ACPI: SSDT 0x7fec8cbc 0000F8 (v01 FSC PST_PR00 00060000 CSF 00000001)
ACPI: SSDT 0x7fec8db4 0000F8 (v01 FSC PST_PR01 00060000 CSF 00000001)
ACPI: SPCR 0x7fec8eac 000050 (v01 PTLTD $UCRTBL$ 00060000 PTL 00000001)
ACPI: MCFG 0x7fec8efc 00003C (v01 PTLTD MCFG 00060000 LTP 00000000)
ACPI: HPET 0x7fec8f38 000038 (v01 PTLTD HPETTBL 00060000 LTP 00000001)
ACPI: APIC 0x7fec8f70 000068 (v01 PTLTD ? APIC 00060000 LTP 00000000)
ACPI: BOOT 0x7fec8fd8 000028 (v01 PTLTD $SBFTBL$ 00060000 LTP 00000001)
ACPI: All ACPI Tables successfully acquired
cpu0 at mainbus0 apid 0: Pentium(R) Dual-Core CPU E5400 @ 2.70GHz, id 0x1067a
cpu1 at mainbus0 apid 1: Pentium(R) Dual-Core CPU E5400 @ 2.70GHz, id 0x1067a
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20131218
acpi0: X/RSDT: OemId <PTLTD , XSDT ,00060000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
MCFG (PNP0C02) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
IFWH (INT0800) at acpi0 not configured
MBRD (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
pckbc1 at acpi0 (KEYB, PNP0303-1) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13-1) (aux port): irq 12
LPT (PNP0400) at acpi0 not configured
COM1 (PNP0501) at acpi0 not configured
ACPI: Enabled 1 GPEs in block 00 to 3F
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-646)
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20131218/hwxface-646)
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x29f0 (rev. 0x01)
wm0 at pci0 dev 25 function 0: 82801I (AMT) LAN Controller (rev. 0x02)
wm0: interrupting at ioapic0 pin 20
wm0: PCI-Express bus
wm0: 2048 words FLASH
wm0: Ethernet address 00:19:99:88:21:32
igphy0 at wm0 phy 1: i82566 10/100/1000 media interface, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2937 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 21
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2938 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 20
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x2939 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x293c (rev. 0x02)
ehci0: interrupting at ioapic0 pin 21
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x2934 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x2935 (rev. 0x02)
uhci4: interrupting at ioapic0 pin 22
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x2936 (rev. 0x02)
uhci5: interrupting at ioapic0 pin 21
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x293a (rev. 0x02)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: wrong number of companions (4 != 3)
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x92)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 7 function 0: vendor 0x1002 product 0x515e (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2916 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x2922 (rev. 0x02)
ahcisata0: interrupting at ioapic0 pin 17
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 6 ports, 32 slots, CAP 0x82009fc5<EMS,CCCS,PMD,ISS=0x0,SAL,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x2930 (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
acpicpu0: C2: I/O, lat 1 us, pow 500 mW
acpicpu0: C3: I/O, lat 57 us, pow 100 mW
acpicpu0: P0: FFH, lat 50 us, pow 100000 mW, 2700 MHz
acpicpu0: P1: FFH, lat 50 us, pow 77000 mW, 2000 MHz
acpicpu0: P2: FFH, lat 50 us, pow 65000 mW, 1600 MHz
acpicpu0: P3: FFH, lat 50 us, pow 52000 mW, 1200 MHz
coretemp0 at cpu0: thermal sensor, 1 C resolution
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
IPsec: Initialized Security Association Processing.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 8 ports with 8 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 1: device present, speed: 3.0Gb/s
ahcisata0 port 2: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <ST3160812AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
umass0 at uhub7 port 5 configuration 1 interface 0
umass0: Imation Imation USB, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Imation, Imation USB, PMAP> disk removable
sd0: 1912 MB, 7648 cyl, 16 head, 32 sec, 512 bytes/sect x 3915776 sectors
ahcisata0 channel 1: clearing WDCTL_RST failed for drive 0
ahcisata0 channel 2: clearing WDCTL_RST failed for drive 0
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Here is 6.1.4's dmesg. wd1 and wd2 work.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.1.4_PATCH (NAO) #0: Sat Jul 19 11:11:00 JST 2014
isaki@nao.XXXXX:/var/obj/6-1/amd64/obj/sys/arch/amd64/compile/NAO
total memory = 4094 MB
avail memory = 3960 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
FUJITSU-SV PRIMERGY ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: Pentium(R) Dual-Core CPU E5400 @ 2.70GHz, id 0x1067a
cpu1 at mainbus0 apid 1: Pentium(R) Dual-Core CPU E5400 @ 2.70GHz, id 0x1067a
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <PTLTD , XSDT ,00060000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
MCFG (PNP0C02) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
IFWH (INT0800) at acpi0 not configured
MBRD (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
pckbc1 at acpi0 (KEYB, PNP0303-1) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13-1) (aux port): irq 12
LPT (PNP0400) at acpi0 not configured
COM1 (PNP0501) at acpi0 not configured
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x29f0 (rev. 0x01)
wm0 at pci0 dev 25 function 0: 82801I (AMT) LAN Controller (rev. 0x02)
wm0: interrupting at ioapic0 pin 20
wm0: PCI-Express bus
wm0: FLASH
wm0: Ethernet address 00:19:99:88:21:32
igphy0 at wm0 phy 1: i82566 10/100/1000 media interface, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2937 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 21
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2938 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 20
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x2939 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x293c (rev. 0x02)
ehci0: interrupting at ioapic0 pin 21
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x2934 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x2935 (rev. 0x02)
uhci4: interrupting at ioapic0 pin 22
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x2936 (rev. 0x02)
uhci5: interrupting at ioapic0 pin 21
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x293a (rev. 0x02)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: wrong number of companions (4 != 3)
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x92)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
genfb0 at pci1 dev 7 function 0: vendor 0x1002 product 0x515e (rev. 0x02)
genfb0: framebuffer at 0xd0000000, size 1024x768, depth 32, stride 4096
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
radeondrm0 at genfb0: ATI ES1000 RN50
radeondrm0: Initialized radeon 1.29.0 20080613
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2916 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x2922 (rev. 0x02)
ahcisata0: interrupting at ioapic0 pin 17
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.20, 6 ports, 32 slots, CAP 0x82009fc5<EMS,CCCS,PMD,ISS=0x0,SAL,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x2930 (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
acpicpu0: C2: I/O, lat 1 us, pow 500 mW
acpicpu0: C3: I/O, lat 57 us, pow 100 mW
acpicpu0: P0: FFH, lat 50 us, pow 100000 mW, 2700 MHz
acpicpu0: P1: FFH, lat 50 us, pow 77000 mW, 2000 MHz
acpicpu0: P2: FFH, lat 50 us, pow 65000 mW, 1600 MHz
acpicpu0: P3: FFH, lat 50 us, pow 52000 mW, 1200 MHz
coretemp0 at cpu0: thermal sensor, 1 C resolution
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 8 ports with 8 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 2: device present, speed: 3.0Gb/s
ahcisata0 port 1: device present, speed: 3.0Gb/s
wd0 at atabus0 drive 0
wd0: <ST3160812AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1 at atabus1 drive 0
wd1: <WDC WD20EZRX-00D8PB0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd2 at atabus2 drive 0
wd2: <ST2000DL001-9VT156>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA)
umass0 at uhub7 port 5 configuration 1 interface 0
umass0: Imation Imation USB, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Imation, Imation USB, PMAP> disk removable
sd0: 1912 MB, 7648 cyl, 16 head, 32 sec, 512 bytes/sect x 3915776 sectors
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
cprng sysctl: WARNING pseudorandom rekeying.
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
>How-To-Repeat:
Boot from USB flush drive which has NetBSD-7.0_RC1-amd64-install.img.gz.
>Fix:
N/A
Home |
Main Index |
Thread Index |
Old Index