Re: kern/48058: bge(4) stops working after booting 5.2_STABLE

To: gnats-bugs%NetBSD.org@localhost
Subject: Re: kern/48058: bge(4) stops working after booting 5.2_STABLE
From: SAITOH Masanobu <msaitoh%execsw.org@localhost>
Date: Thu, 18 Jul 2013 02:32:34 +0900
(2013/07/18 2:25), he%uninett.no@localhost wrote:
>> Number:         48058
>> Category:       kern
>> Synopsis:       bge(4) stops working after booting 5.2_STABLE
>> Confidential:   no
>> Severity:       serious
>> Priority:       high
>> Responsible:    kern-bug-people
>> State:          open
>> Class:          sw-bug
>> Submitter-Id:   net
>> Arrival-Date:   Wed Jul 17 17:25:00 +0000 2013
>> Originator:     Havard Eidnes
>> Release:        NetBSD 5.2_STABLE
>> Organization:
>       UNINETT AS
>> Environment:
>       
>       
> System: NetBSD hegre.uninett.no 5.1_STABLE NetBSD 5.1_STABLE (GENERIC) #0: 
> Mon Oct 29 23:29:28 CET 2012  
> he%hegre.uninett.no@localhost:/usr/obj/sys/arch/i386/compile/GENERIC i386
> Architecture: i386
> Machine: i386
>> Description:
>       I'm trying to upgrade an IBM eServer 306m to 5.2_STABLE from
>       the 5.1_STABLE kernel shown above.
> 
>       During boot-up of the 5.2_STABLE GENERIC kernel, the kernel
>       messages contain:
> 
> bge1 at pci5 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge1: interrupting at ioapic0 pin 17
> adjust device control 0x1a2100 -> 0x1a5100
> bge1: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8f
> brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy1: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> 
>       and the kernel refuses to assign an IPv4 or IPv6 address via
>       ifconfig with
> 
> hegre# ifconfig bge1 inet 128.39.2.22 netmask 255.255.255.0
> ifconfig: SIOCAIFADDR: Invalid argument
> hegre# exit
> 
>       Rebooting (warm) with the old 5.1_STABLE kernel does however
>       not restore a working network interface, the kernel messages
>       there now contain:
> 
> bge0 at pci4 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge0: interrupting at ioapic0 pin 16
> adjust device control 0x1a2100 -> 0x1a5100
> bge0: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8e
> brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy0: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> bge1 at pci5 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge1: interrupting at ioapic0 pin 17
> bge1: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8f
> bge1: setting short Tx thresholds
> brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy1: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> 
>       At least "ifconfig -m bge1" seems to agree with the kernel
>       messages.
> 
>       On closer inspection, I see that in NetBSD 5.2_STABLE, a lot
>       of the PCI busses are detected as PCI-Express, while that was
>       not the case with the 5.1_STABLE kernel.
> 
>       Kernel boot messages for the two kernels follow.
> 
>       I just hope the 5.1_STABLE kernel will come up working if I
>       can get some remote hands to power-cycle the machine
>       tomorrow...
> 
> 
> 
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>     2006, 2007, 2008, 2009, 2010
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 5.2_STABLE (GENERIC) #1: Wed Jul 17 15:18:24 CEST 2013
>       he%hegre.uninett.no@localhost:/usr/obj/sys/arch/i386/compile/GENERIC
> total memory = 2046 MB
> avail memory = 1999 MB
> IBM IBM eServer 306m -[884930Y]- (IBM CORPORATION)
> mainbus0 (root)
> cpu0 at mainbus0 apid 0: Intel 686-class, 3200MHz, id 0xf43
> cpu1 at mainbus0 apid 1: Intel 686-class, 3200MHz, id 0xf43
> ioapic0 at mainbus0 apid 2
> acpi0 at mainbus0: Intel ACPICA 20080321
> npx1 at acpi0 (MATH, PNP0C04): io 0xf0-0xfe irq 13
> pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
> midi0 at pcppi1: PC speaker (CPU-intensive output)
> sysbeep0 at pcppi1
> attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
> FWH (INT0800) at acpi0 not configured
> COM1 (PNP0501) at acpi0 not configured
> pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1
> pckbc2 at acpi0 (MSE0, PNP0F13) (aux port): irq 12
> acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
> apm0 at acpi0: Power Management spec V1.2
> attimer1: attached to pcppi1
> ipmi0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1
> pchb0 at pci0 dev 0 function 0
> pchb0: vendor 0x8086 product 0x2778 (rev. 0x81)
> ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2779 (rev. 0x81)
> ppb0: PCI Express 1.0 <Root Port of PCI-E Root Complex>
> pci1 at ppb0 bus 1
> pci1: no spaces enabled!
> ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
> ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
> pci2 at ppb1 bus 2
> ppb2 at pci2 dev 0 function 0: vendor 0x8086 product 0x032c (rev. 0x09)
> ppb2: PCI Express 1.0 <PCI-E to PCI/PCI-X Bridge>
> pci3 at ppb2 bus 3
> vendor 0x8086 product 0x0326 (interrupt system, interface 0x20, revision 
> 0x09) at pci2 dev 0 function 1 not configured
> ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x27e0 (rev. 0x01)
> ppb3: PCI Express 1.0 <Root Port of PCI-E Root Complex>
> pci4 at ppb3 bus 4
> bge0 at pci4 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge0: interrupting at ioapic0 pin 16
> adjust device control 0x1a2100 -> 0x1a5100
> bge0: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8e
> brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x27e2 (rev. 0x01)
> ppb4: PCI Express 1.0 <Root Port of PCI-E Root Complex>
> pci5 at ppb4 bus 5
> bge1 at pci5 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge1: interrupting at ioapic0 pin 17
> adjust device control 0x1a2100 -> 0x1a5100
> bge1: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8f
> brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy1: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
> uhci0: interrupting at ioapic0 pin 23
> usb0 at uhci0: USB revision 1.0
> uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
> uhci1: interrupting at ioapic0 pin 19
> usb1 at uhci1: USB revision 1.0
> uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
> uhci2: interrupting at ioapic0 pin 18
> usb2 at uhci2: USB revision 1.0
> ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
> ehci0: interrupting at ioapic0 pin 23
> ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
> usb3 at ehci0: USB revision 2.0
> ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
> pci6 at ppb5 bus 10
> vga1 at pci6 dev 4 function 0: vendor 0x1002 product 0x515e (rev. 0x01)
> wsdisplay0 at vga1 kbdmux 1
> drm at vga1 not configured
> ichlpcib0 at pci0 dev 31 function 0
> ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
> ichlpcib0: 24-bit timer
> piixide0 at pci0 dev 31 function 2
> piixide0: Intel 82801GB/GR Serial ATA/Raid Controller (ICH7) (rev. 0x01)
> piixide0: primary channel interrupting at ioapic0 pin 14
> atabus0 at piixide0 channel 0
> piixide0: secondary channel interrupting at ioapic0 pin 15
> atabus1 at piixide0 channel 1
> ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
> ichsmb0: interrupting at ioapic0 pin 19
> iic0 at ichsmb0: I2C bus
> isa0 at ichlpcib0
> com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> com0: console
> uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> wd0 at atabus0 drive 0uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, 
> rev 1.00/1.00, addr 1
> uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> : <WDC WD800JD-23LSA0>
> wd0: 76324 MB, 155072 cyl, 16 head, 63 sec, 512 bytes/sect x 156312576 sectors
> wd1 at atabus0 drive 1: <HDS728080PLA380 39M3701 26K5308IBM>
> wd1: 76324 MB, 155072 cyl, 16 head, 63 sec, 512 bytes/sect x 156312576 sectors
> atapibus0 at atabus1: 2 targets
> cd0 at atapibus0 drive 0: <HL-DT-ST  GCR-8240N, , 1.06> cdrom removable
> Kernelized RAIDframe activated
> pad0: outputs: 44100Hz, 16-bit, stereo
> audio0 at pad0: half duplex, playback, capture
> raid0: RAID Level 1
> raid0: Components: /dev/wd0a /dev/wd1a
> raid0: Total Sectors: 156312448 (76324 MB)
> boot device: raid0
> root on raid0a dumps on raid0b
> root file system type: ffs
> Wed Jul 17 14:12:10 GMT 2013
> 
> 
> ...and this is after the brief period with 5.2_STABLE running:
> 
> 
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>     2006, 2007, 2008, 2009, 2010
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 5.1_STABLE (GENERIC) #0: Mon Oct 29 23:29:28 CET 2012
>       he%hegre.uninett.no@localhost:/usr/obj/sys/arch/i386/compile/GENERIC
> total memory = 2046 MB
> avail memory = 1999 MB
> IBM IBM eServer 306m -[884930Y]- (IBM CORPORATION)
> mainbus0 (root)
> cpu0 at mainbus0 apid 0: Intel 686-class, 3200MHz, id 0xf43
> cpu1 at mainbus0 apid 1: Intel 686-class, 3200MHz, id 0xf43
> ioapic0 at mainbus0 apid 2
> acpi0 at mainbus0: Intel ACPICA 20080321
> npx1 at acpi0 (MATH, PNP0C04): io 0xf0-0xfe irq 13
> pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
> midi0 at pcppi1: PC speaker (CPU-intensive output)
> sysbeep0 at pcppi1
> attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
> FWH (INT0800) at acpi0 not configured
> COM1 (PNP0501) at acpi0 not configured
> pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1
> pckbc2 at acpi0 (MSE0, PNP0F13) (aux port): irq 12
> acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
> apm0 at acpi0: Power Management spec V1.2
> attimer1: attached to pcppi1
> ipmi0 at mainbus0
> pci0 at mainbus0 bus 0: configuration mode 1
> pchb0 at pci0 dev 0 function 0
> pchb0: vendor 0x8086 product 0x2778 (rev. 0x81)
> ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2779 (rev. 0x81)
> pci1 at ppb0 bus 1
> pci1: no spaces enabled!
> ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
> pci2 at ppb1 bus 2
> ppb2 at pci2 dev 0 function 0: vendor 0x8086 product 0x032c (rev. 0x09)
> ppb2: disabling notification events
> pci3 at ppb2 bus 3
> vendor 0x8086 product 0x0326 (interrupt system, interface 0x20, revision 
> 0x09) at pci2 dev 0 function 1 not configured
> ppb3 at pci0 dev 28 function 4: vendor 0x8086 product 0x27e0 (rev. 0x01)
> pci4 at ppb3 bus 4
> bge0 at pci4 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge0: interrupting at ioapic0 pin 16
> adjust device control 0x1a2100 -> 0x1a5100
> bge0: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8e
> brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy0: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> ppb4 at pci0 dev 28 function 5: vendor 0x8086 product 0x27e2 (rev. 0x01)
> pci5 at ppb4 bus 5
> bge1 at pci5 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
> bge1: interrupting at ioapic0 pin 17
> adjust device control 0x1a2100 -> 0x1a5100
> bge1: ASIC BCM5750 B1 (0x4101), Ethernet address 00:11:25:22:6c:8f
> brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
> brgphy1: no media present
> ifmedia_set: no match for 0x20/0xffffffff
> uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
> uhci0: interrupting at ioapic0 pin 23
> usb0 at uhci0: USB revision 1.0
> uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
> uhci1: interrupting at ioapic0 pin 19
> usb1 at uhci1: USB revision 1.0
> uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
> uhci2: interrupting at ioapic0 pin 18
> usb2 at uhci2: USB revision 1.0
> ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
> ehci0: interrupting at ioapic0 pin 23
> ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
> usb3 at ehci0: USB revision 2.0
> ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xe1)
> pci6 at ppb5 bus 10
> vga1 at pci6 dev 4 function 0: vendor 0x1002 product 0x515e (rev. 0x01)
> wsdisplay0 at vga1 kbdmux 1
> drm at vga1 not configured
> ichlpcib0 at pci0 dev 31 function 0
> ichlpcib0: vendor 0x8086 product 0x27b8 (rev. 0x01)
> ichlpcib0: 24-bit timer
> piixide0 at pci0 dev 31 function 2
> piixide0: Intel 82801GB/GR Serial ATA/Raid Controller (ICH7) (rev. 0x01)
> piixide0: primary channel interrupting at ioapic0 pin 14
> atabus0 at piixide0 channel 0
> piixide0: secondary channel interrupting at ioapic0 pin 15
> atabus1 at piixide0 channel 1
> ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x01)
> ichsmb0: interrupting at ioapic0 pin 19
> iic0 at ichsmb0: I2C bus
> isa0 at ichlpcib0
> com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> com0: console
> uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> wd0 at atabus0 drive 0: <WDC WD800JD-23LSA0>
> wd0: 76324 MB, 155072 cyl, 16 head, 63 sec, 512 bytes/sect x 156312576 sectors
> wd1 at atabus0 drive 1: <HDS728080PLA380 39M3701 26K5308IBM>
> wd1: 76324 MB, 155072 cyl, 16 head, 63 sec, 512 bytes/sect x 156312576 sectors
> atapibus0 at atabus1: 2 targets
> cd0 at atapibus0 drive 0: <HL-DT-ST  GCR-8240N, , 1.06> cdrom removable
> Kernelized RAIDframe activated
> pad0: outputs: 44100Hz, 16-bit, stereo
> audio0 at pad0: half duplex, playback, capture
> raid0: RAID Level 1
> raid0: Components: /dev/wd0a /dev/wd1a
> raid0: Total Sectors: 156312448 (76324 MB)
> boot device: raid0
> root on raid0a dumps on raid0b
> root file system type: ffs
> Wed Jul 17 14:20:58 GMT 2013
> 
> 
>> How-To-Repeat:
>       Try to upgrade to 5.2_STABLE on an IBM eServer 306m.
>       Watch network interfaces come up with no recognized media.
>       
>> Fix:
>       Sorry, don't know.
> 
>> Unformatted:

Could you test with the latest -current if the bge(4) works?


-- 
-----------------------------------------------
                SAITOH Masanobu (msaitoh%execsw.org@localhost
                                 msaitoh%netbsd.org@localhost)
References:
- kern/48058: bge(4) stops working after booting 5.2_STABLE
  - From: he
Prev by Date: Re: kern/48058 (bge(4) stops working after booting 5.2_STABLE)
Next by Date: Re: kern/48058: bge(4) stops working after booting 5.2_STABLE
Previous by Thread: kern/48058: bge(4) stops working after booting 5.2_STABLE
Next by Thread: Re: kern/48058: bge(4) stops working after booting 5.2_STABLE
Indexes:
Home | Main Index | Thread Index | Old Index