NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: install/47021: 6.0 RC2 sysinst not find any hard disks on Powermac G3 B&W
The following reply was made to PR port-macppc/47021; it has been noted by
GNATS.
From: sadirux <sadirux%goja.fr@localhost>
To: <gnats-bugs%netbsd.org@localhost>
Cc:
Subject: Re: install/47021: 6.0 RC2 sysinst not find any hard disks on
Powermac G3 B&W
Date: Tue, 02 Oct 2012 23:00:24 +0200
Hello,
These are the logs :
netppc# uname -rs
NetBSD 5.1
netppc# pcictl pci1 list
001:00:0: Texas Instruments TSB12LV21 IEEE 1394 Host Controller
(Firewire serial bus, revision 0x02)
001:01:0: CMD Technology PCI0646 (IDE mass storage, interface 0x8f,
revision 0x05)
001:02:0: Brooktree Bt878 Video Capture (video multimedia, revision
0x11)
001:02:1: Brooktree Bt878 Video Capture (Audio Section) (miscellaneous
multimedia, revision 0x11)
001:05:0: Apple Computer Paddington I/O Controller (undefined subclass
0x00)
001:06:0: Opti 82C861 (USB serial bus, interface 0x10, revision 0x10)
netppc# pcictl pci1 dump -d 1
PCI configuration registers:
Common header:
0x00: 0x06461095 0x02900005 0x01018f05 0x00001000
Vendor Name: CMD Technology (0x1095)
Device Name: PCI0646 (0x0646)
Command register: 0x0005
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: IDE (0x01)
Interface: 0x8f
Revision ID: 0x05
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x10
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00001091 0x00001081 0x00001071 0x00001061
0x20: 0x00001051 0x00000000 0x00000000 0x06461095
0x30: 0x00000000 0x00000060 0x00000000 0x0402011a
Base address register at 0x10
type: i/o
base: 0x00001090, not sized
Base address register at 0x14
type: i/o
base: 0x00001080, not sized
Base address register at 0x18
type: i/o
base: 0x00001070, not sized
Base address register at 0x1c
type: i/o
base: 0x00001060, not sized
Base address register at 0x20
type: i/o
base: 0x00001050, not sized
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1095
Subsystem ID: 0x0646
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x60
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x04
Minimum Grant: 0x02
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x1a
Capability register at 0x60
type: 0x01 (Power Management, rev. 1.0)
PCI Power Management Capabilities Register
Capabilities register: 0x0601
Version: 1.0
PME# clock: off
Device specific initialization: off
3.3V auxiliary current: self-powered
D1 power management state support: on
D2 power management state support: on
PME# support: 0x00
Control/status register: 0x6000
Power state: D0
PCI Express reserved: off
No soft reset: off
PME# assertion disabled
PME# status: off
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x02000000
0x50: 0xc000e440 0xcc00c03f 0x00004000 0x00000000
0x60: 0x06010001 0x80006000 0x00000000 0x00000000
0x70: 0xd1200000 0x10050000 0xf0000000 0x78fe76d0
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
I would install a new kernel tomorrow
Sadirux
---
(envoyé depuis un webmail libre)
Le 2012-10-02 02:40, Michael a écrit :
> The following reply was made to PR port-macppc/47021; it has been
> noted
> by GNATS.
>
> From: Michael <macallan%netbsd.org@localhost>
> To: gnats-bugs%NetBSD.org@localhost
> Cc:
> Subject: Re: install/47021: 6.0 RC2 sysinst not find any hard disks
> on
> Powermac G3 B&W
> Date: Mon, 1 Oct 2012 20:35:31 -0400
>
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hello,
>
> On Oct 1, 2012, at 4:10 PM, sadirux wrote:
>
> I think the problem is right here:
> > cmdide0 at pci1 dev 1 function 0: CMD Technology PCI0646 (rev.
> 0x05)
> > cmdide0: bus-master DMA support present, but unused (couldn't map
> > registers)
>
> Please mail me the pcictl dump output for this IDE controller. I bet
> =20
> there's a BAT mapping missing somewhere.
> I think I fixed a similar looking bug in that area ( in order to get
> a
> =20=
>
> trm to work on a beige G3 ), not sure if that was before or after the
> =20=
>
> 6.0 branch. Does a -current kernel work any better?
>
> have fun
> Michael
>
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.4.7 (Darwin)
> Comment: GPGTools - http://gpgtools.org [1]
>
> iQEVAwUBUGo208pnzkX8Yg2nAQI9Dgf+PZIjZnliw9fyPL3Qzj0PtT3+Us6WVgj4
> zhtwI1VTW/3fMzH8lHyksidk2IjBxIFheDCxxWi9LHbYMihRcE9MGtaCpgZb2zmP
> BExZQ//xrk6juiYoVpRn017xp7lSKqKILuOvFVh3QHSpWFNlvDep3paKoBmcfkuA
> bZrrK7xnTNjeIHSin6YQ9tC+YOVPd7VyTIGJO6R/2WU+5KFAl2NTFlr4tWkzUsZJ
> 8/jcmOqn9mBbOQ7MxKp0c/a007WPqHYyuSsHtgSTkZyJpHOVA7qR9HW7UKyGLobc
> njiAxTpCXN5YzuSZZRJDRYMXxxQknTKLumA7vDtjclj7H1I/IhQp+Q=3D=3D
> =3DTE+Q
> -----END PGP SIGNATURE-----
Links:
------
[1] http://gpgtools.org
Home |
Main Index |
Thread Index |
Old Index