NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: port-sparc/46572: Invalid argument accessing qe* (qec) interfaces w/NetBSD-6.0_BETA2/sparc
The following reply was made to PR port-sparc/46572; it has been noted by GNATS.
From: "John D. Baker" <jdbaker%mylinuxisp.com@localhost>
To: gnats-bugs%NetBSD.org@localhost
Cc:
Subject: Re: port-sparc/46572: Invalid argument accessing qe* (qec) interfaces
w/NetBSD-6.0_BETA2/sparc
Date: Sun, 10 Jun 2012 11:52:37 -0500 (CDT)
On Sun, 10 Jun 2012, Martin Husemann wrote:
> This does not look right. Please provide full dmesg output from NetBSD
> and output of "printenv" at the firmware prompt.
As found in /var/run/dmesg.boot (machine is net-booted for these tests,
MAC addresses obfuscated):
initialized boothowt from bootloader: 0
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.0_BETA2 (GENERIC) #5: Thu Jun 7 09:29:58 CDT 2012
sysop%verthandi.technoskunk.fur@localhost:/d0/build/netbsd-6/obj/sparc/sys/arch/sparc/compile/GENERIC
total memory = 97984 KB
avail memory = 91280 KB
timecounter: Timecounters tick every 10.000 msec
bootpath: /iommu@0,10000000/sbus@0,10001000/ledma@5,8400010/le@5,8c00000
mainbus0 (root): SUNW,SPARCstation-5: hostid 80772960
cpu0 at mainbus0: MB86904 @ 85 MHz, on-chip FPU
cpu0: 16K instruction (32 b/l), 8K data (16 b/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x200000: mk48t08
timer0 at obio0 slot 0 offset 0xd00000: delay constant 40, frequency = 2000000
Hz
timecounter: Timecounter "timer-counter" frequency 2000000 Hz quality 100
zs0 at obio0 slot 0 offset 0x100000 level 12 softpri 6
zstty0 at zs0 channel 0 (console i/o)
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
zstty4 at zs1 channel 0
kbd0 at zstty4
zstty5 at zs1 channel 1
ms0 at zstty5
wsmouse0 at ms0 mux 0
slavioconfig at obio0 slot 0 offset 0x800000 not configured
auxreg0 at obio0 slot 0 offset 0x900000
power0 at obio0 slot 0 offset 0x910000 level 2
fdc0 at obio0 slot 0 offset 0x400000 level 11: no drives attached
iommu0 at mainbus0 addr 0x10000000: version 0x4/0x0, page-size 4096, range 64MB
sbus0 at iommu0: clock = 21.250 MHz
dma0 at sbus0 slot 5 offset 0x8400000: DMA rev 2
esp0 at dma0 slot 5 offset 0x8800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
bpp0 at sbus0 slot 5 offset 0xc800000 level 2 (ipl 3): DMA rev 2
ledma0 at sbus0 slot 5 offset 0x8400010: DMA rev 2
le0 at ledma0 slot 5 offset 0x8c00000 level 6: address c0:ff:ee:c0:ff:ee
le0: 8 receive buffers, 2 transmit buffers
audiocs0 at sbus0 slot 4 offset 0xc000000 level 9: CS4231A
audio0 at audiocs0: full duplex, playback, capture
power-management at sbus0 slot 4 offset 0xa000000 not configured
qec0 at sbus0 slot 1 offset 0x20000 level 4 (ipl 7): 128K memory
qe0 at qec0 slot 0 offset 0x0 rev 1 address c0:ff:ee:c0:ff:ee
qe1 at qec0 slot 1 offset 0x0 rev 1 address c0:ff:ee:c0:ff:ee
qe2 at qec0 slot 2 offset 0x0 rev 1 address c0:ff:ee:c0:ff:ee
qe3 at qec0 slot 3 offset 0x0 rev 1 address c0:ff:ee:c0:ff:ee
magma0 at sbus0 slot 3 offset 0x0 level 9: Magma LC 2+1 Sp
mtty0 at magma0: 2 ttys
mbpp0 at magma0: 1 port
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
scsibus0: waiting 2 seconds for devices to settle...
wskbd0 at kbd0 mux 1
sd0 at scsibus0 target 1 lun 0: <SEAGATE, ST5660N SUN0535, 0644> disk fixed
sd0: 520 MB, 3002 cyl, 4 head, 88 sec, 512 bytes/sect x 1065664 sectors
sd0: sync (100.00ns offset 15), 8-bit (10.000MB/s) transfers, tagged queueing
kbd0: reset failed
Kernelized RAIDframe activated
root on le0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 192.168.17.4
nfs_boot: my_name=ossian
nfs_boot: my_domain=technoskunk.fur
nfs_boot: my_addr=192.168.17.8
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.17.8
root on 192.168.17.4:/r0/diskless/ossian
root file system type: nfs
And from 'printenv':
ok printenv
Parameter Name Value Default Value
tpe-link-test? true true
output-device ttya screen
input-device ttya keyboard
keyboard-click? false false
keymap
ttyb-rts-dtr-off false false
ttyb-ignore-cd true true
ttya-rts-dtr-off false false
ttya-ignore-cd true true
ttyb-mode 9600,8,n,1,- 9600,8,n,1,-
ttya-mode 9600,8,n,1,- 9600,8,n,1,-
fcode-debug? false false
local-mac-address? false false
screen-#columns 80 80
screen-#rows 34 34
selftest-#megs 1 1
scsi-initiator-id 7 7
silent-mode? false false
auto-boot? true true
watchdog-reboot? false false
diag-file
diag-device net net
boot-file
boot-device disk1 net disk net
sbus-probe-list 541230 541230
use-nvramrc? false false
nvramrc
sunmon-compat? false false
security-mode none none
security-password
security-#badlogins 0 <no default>
oem-logo <no default>
oem-logo? false false
oem-banner <no default>
oem-banner? false false
hardware-revision <no default>
last-hardware-update <no default>
testarea 0 0
mfg-switch? false false
diag-switch? false false
--
|/"\ John D. Baker, KN5UKS NetBSD Darwin/MacOS X
|\ / jdbaker[snail]mylinuxisp[flyspeck]com OpenBSD FreeBSD
| X No HTML/proprietary data in email. BSD just sits there and works!
|/ \ GPGkeyID: D703 4A7E 479F 63F8 D3F4 BD99 9572 8F23 E4AD 1645
Home |
Main Index |
Thread Index |
Old Index