Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL status 3)

[Dalibor Gudzic <dalibor.gudzic%gmail.com@localhost>]

On Sat, Oct 22, 2011 at 7:05 PM, Dalibor Gudzic
<dalibor.gudzic%gmail.com@localhost> wrote:
> The following reply was made to PR port-i386/40507; it has been noted by 
> GNATS.
>
> From: Dalibor Gudzic <dalibor.gudzic%gmail.com@localhost>
> To: gnats-bugs%netbsd.org@localhost
> Cc: port-i386-maintainer%netbsd.org@localhost, 
> netbsd-bugs%netbsd.org@localhost,
>        gnats-admin%netbsd.org@localhost
> Subject: Re: port-i386/40507 (AR5005G - ath0: unable to attach hardware; HAL
>  status 3)
> Date: Sat, 22 Oct 2011 19:03:11 +0200
>
>  Hi,
>
>  On Sat, Oct 22, 2011 at 5:26 PM,  <jmcneill%netbsd.org@localhost> wrote:
>  > Synopsis: AR5005G - ath0: unable to attach hardware; HAL status 3
>  >
>  > State-Changed-From-To: open->feedback
>  > State-Changed-By: jmcneill%NetBSD.org@localhost
>  > State-Changed-When: Sat, 22 Oct 2011 15:26:49 +0000
>  > State-Changed-Why:
>  > can you re-test with -current?
>  >

I tested with -current snapshot from about two weeks ago,
unfortunately no joy. :( Here's the full dmesg:


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.56 (GENERIC) #0: Sat Oct 22 15:06:19 UTC 2011
        
builds%b8.netbsd.org@localhost:/home/builds/ab/HEAD/i386/201110220850Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 1406 MB
avail memory = 1369 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
FUJITSU SIEMENS AMILO PRO V3515 (20)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel(R) Celeron(R) M CPU        430  @
1.73GHz, id 0x6e8
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 3, 24 pins
ioapic1 at mainbus0 apid 2: pa 0xfecc0000, version 3, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <FSC   ,PC      ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 10
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
NBPE (PNP0C01) at acpi0 not configured
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
MEM (PNP0C01) at acpi0 not configured
SYSR (PNP0C02) at acpi0 not configured
pckbc1 at acpi0 (PS2M, STL3842) (aux port): irq 12
pckbc2 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
acpivga0 at acpi0 (VGA): ACPI Display Adapter
acpiout0 at acpivga0 (CRT, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
acpivga0: connected output devices:
acpivga0:   0x0100 (acpiout0): Ext. Monitor, head 0, bios detect
acpivga0:   0x0110 (acpiout1): LCD Panel, head 0, bios detect
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery
acpifan0 at acpi0 (FAN, PNP0C0B): ACPI Fan
acpitz0 at acpi0 (THRM): cpu0
acpitz0: active cooling level 0: 59.8C
acpitz0: levels: critical 109.8 C, passive 65.8 C
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1106 product 0x0364 (rev. 0x00)
agp0 at pchb0: aperture at 0xc0000000, size 0x8000000
pchb1 at pci0 dev 0 function 1: vendor 0x1106 product 0x1364 (rev. 0x00)
pchb2 at pci0 dev 0 function 2: vendor 0x1106 product 0x2364 (rev. 0x00)
pchb3 at pci0 dev 0 function 3: vendor 0x1106 product 0x3364 (rev. 0x00)
pchb4 at pci0 dev 0 function 4: vendor 0x1106 product 0x4364 (rev. 0x00)
vendor 0x1106 product 0x5364 (interrupt system, interface 0x20) at
pci0 dev 0 function 5 not configured
pchb5 at pci0 dev 0 function 6: vendor 0x1106 product 0x6364 (rev. 0x00)
pchb6 at pci0 dev 0 function 7: vendor 0x1106 product 0x7364 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0xb198 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: vendor 0x1106 product 0x3371 (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
viadrm0 at vga1: VIA P4M900 / VN896
viadrm0: AGP at 0xc0000000 128MB
viadrm0: Initialized via 2.11.1 20070202
ppb1 at pci0 dev 2 function 0: vendor 0x1106 product 0xa364 (rev. 0x80)
ppb1: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 3 function 0: vendor 0x1106 product 0xc364 (rev. 0x80)
ppb2: PCI Express 1.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
viaide0 at pci0 dev 15 function 0: VIA Technologies VT8237A SATA
Controller (rev. 0x80)
viaide0: bus-master DMA support present
viaide0: primary channel configured to native-PCI mode
viaide0: using ioapic0 pin 21 for native-PCI interrupt
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to native-PCI mode
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 15 function 1
viaide1: VIA Technologies VT8237A ATA133 controller
viaide1: bus-master DMA support present
viaide1: primary channel configured to compatibility mode
viaide1: primary channel ignored (disabled)
viaide1: secondary channel configured to compatibility mode
viaide1: secondary channel interrupting at ioapic0 pin 15
atabus2 at viaide1 channel 1
uhci0 at pci0 dev 16 function 0: vendor 0x1106 product 0x3038 (rev. 0xa0)
uhci0: interrupting at ioapic0 pin 20
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 16 function 1: vendor 0x1106 product 0x3038 (rev. 0xa0)
uhci1: interrupting at ioapic0 pin 22
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 16 function 2: vendor 0x1106 product 0x3038 (rev. 0xa0)
uhci2: interrupting at ioapic0 pin 21
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 16 function 3: vendor 0x1106 product 0x3038 (rev. 0xa0)
uhci3: interrupting at ioapic0 pin 23
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 16 function 4: vendor 0x1106 product 0x3104 (rev. 0x86)
ehci0: interrupting at ioapic0 pin 21
ehci0: dropped intr workaround enabled
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
viapcib0 at pci0 dev 17 function 0: vendor 0x1106 product 0x3337 (rev. 0x00)
viapcib0: SMBus found at 0x4100 (revision 0x0)
iic0 at viapcib0: I2C bus
pchb7 at pci0 dev 17 function 7: vendor 0x1106 product 0x287e (rev. 0x00)
vr0 at pci0 dev 18 function 0: vendor 0x1106 product 0x3065 (rev. 0x7c)
vr0: interrupting at ioapic0 pin 23
vr0: Ethernet address: 00:14:0b:08:64:5b
ukphy0 at vr0 phy 1: OUI 0x0002c6, model 0x0032, rev. 10
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb3 at pci0 dev 19 function 0: vendor 0x1106 product 0x337b (rev. 0x00)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
hdaudio0 at pci4 dev 1 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 17
hdafg0 at hdaudio0: Conexant CX20549
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: ADC01 2ch: Mic In [Jack] [Built-In]
hdafg0: DIG02 2ch: SPDIF Out [Jack]
hdafg0: 2ch/2ch 48000Hz 96000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, independent
hdvsmfg at hdaudio0 not configured
ppb4 at pci0 dev 19 function 1: vendor 0x1106 product 0x337a (rev. 0x00)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
ath0 at pci5 dev 1 function 0: Atheros 2413
ath0: interrupting at ioapic0 pin 18
ath0: unable to attach hardware; HAL status 3
isa0 at viapcib0
isapnp0 at isa0 port 0x279
isapnp0: no ISA Plug 'n Play devices found
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
acpicpu0: C2: I/O, lat   1 us, pow   500 mW, bus master check
coretemp0 at cpu0: thermal sensor, 1 C resolution
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1729214890 Hz quality 3000
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
viaide0 port 0: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0
wd0: <WDC WD600BEVS-07LAT0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
ehci0: handing over low speed device on port 2 to uhci0
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T10N, M006BM21412,
PW02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide1:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
boot device: cd0
root on cd0a dumps on cd0b
root file system type: cd9660
warning: no /dev/console
uhidev0 at uhub0 port 2 configuration 1 interface 0
uhidev0: vendor 0x15d9 USB Mouse, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir
wsmouse1 at ums0 mux 0


I am available for any further testing or more info.

All best