re: kern/40279: import bwi(4), driver for Broadcom BCM43xx 802.11 wifi devices, including Apple's AirPort Extreme

[Alexey Lebedev <realzhtw%gmail.com@localhost>]

Hello!

I'm a user of Compaq Pressario V3614AU with broadcom bcm4311 wifi card.

I tried to use your patch to get it to work. That's what I have in my
dmesg after recompiling the kernel (recompilation was done under
FreeBSD machine for speed up):

bwi0: interrupting at ioapic0 pin 22
bwi0: BBP id 0x4311, BBP rev 0x2, BBP pkg 0
bwi0: MAC rev 13 is not supported
bwi0: no MAC was found

Full dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0.0_PATCH (OSU) #0: Sun May  3 02:48:40 MSD 2009
        
avl%samanka.zhtw.org.ru@localhost:/usr/home/avl/build/netbsd/src/sys/arch/amd64/compile/obj/OSU
total memory = 1982 MB
avail memory = 1906 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.4 @ 0xdc010 (27 entries)
Hewlett-Packard Presario V3500 Notebook PC (F.13)
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 1900MHz, id 0x60f82
cpu0: SVM disabled by the BIOS
cpu1 at mainbus0 apid 1: AMD 686-class, 1900MHz, id 0x60f82
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 11, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <HPQOEM,SLIC-MPC,06040000>, AslId < LTP,00000000>
LNK1: ACPI: Found matching pin for 1.9.INTA at func 0: 10
LNK2: ACPI: Found matching pin for 1.9.INTB at func 1: 11
LNK2: BIOS IRQ 11 does not match initial IRQ 10
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
hpqlb0 at acpi0 (QLBD, HPQ0006): HP Quick Launch Buttons
WMID (PNP0C14) at acpi0 not configured
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpibut1 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
hpet0 at acpi0 (MMTM, PNP0103-0)
hpet0: mem 0xfed00000-0xfed003ff irq 0,8
timecounter: Timecounter "hpet0" frequency 25000000 Hz quality 2000
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpidalb0 at acpi0 (MCEB, PNP0C32-4): Direct Application Launch Button
acpidalb1 at acpi0 (DVDB, PNP0C32-2): Direct Application Launch Button
acpidalb2 at acpi0 (QPWB, PNP0C32-1): Direct Application Launch Button
acpidalb3 at acpi0 (PICB, PNP0C32-6): Direct Application Launch Button
acpidalb4 at acpi0 (VDOB, PNP0C32-7): Direct Application Launch Button
acpidalb5 at acpi0 (LTVB, PNP0C32-8): Direct Application Launch Button
acpidalb6 at acpi0 (MUSB, PNP0C32-3): Direct Application Launch Button
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: Hewlett-Packard , LION, Primary
acpiacad0 at acpi0 (ADP1, ACPI0003): ACPI AC Adapter
attimer1 at acpi0 (PIT0, PNP0100): AT Timer
attimer1: io 0x40-0x43
pcppi1 at acpi0 (SPK0, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (KBD0, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, AUI1501): aux port
pckbc2: irq 12
acpitz0 at acpi0 (TZS0): critical 120.0C hot 100.0C passive 79.0C,
passive cooling
acpitz1 at acpi0 (TZS1): critical 120.0C hot 126.0C, passive cooling
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
vendor 0x10de product 0x0547 (RAM memory, revision 0xa2) at pci0 dev 0
function 0 not configured
pcib0 at pci0 dev 1 function 0
pcib0: vendor 0x10de product 0x0548 (rev. 0xa2)
nfsmbc0 at pci0 dev 1 function 1: vendor 0x10de product 0x0542 (rev. 0xa2)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
vendor 0x10de product 0x0541 (RAM memory, revision 0xa2) at pci0 dev 1
function 2 not configured
vendor 0x10de product 0x0543 (Co-processor processor, revision 0xa2)
at pci0 dev 1 function 3 not configured
ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x055e (rev. 0xa2)
LUS0: Picked IRQ 17 with weight 0
ohci0: interrupting at ioapic0 pin 17
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 2 function 1: vendor 0x10de product 0x055f (rev. 0xa2)
LUS2: Picked IRQ 17 with weight 1
ehci0: interrupting at ioapic0 pin 17
ehci0: EHCI version 1.0
ehci0: companion controller, 12 ports each: ohci0
usb1 at ehci0: USB revision 2.0
ohci1 at pci0 dev 4 function 0: vendor 0x10de product 0x055e (rev. 0xa2)
Z012: Picked IRQ 16 with weight 0
ohci1: interrupting at ioapic0 pin 16
ohci1: OHCI version 1.0, legacy support
usb2 at ohci1: USB revision 1.0
ehci1 at pci0 dev 4 function 1: vendor 0x10de product 0x055f (rev. 0xa2)
Z013: Picked IRQ 16 with weight 1
ehci1: interrupting at ioapic0 pin 16
ehci1: EHCI version 1.0
ehci1: companion controller, 12 ports each: ohci1
usb3 at ehci1: USB revision 2.0
viaide0 at pci0 dev 6 function 0
viaide0: NVIDIA MCP67 IDE Controller (rev. 0xa1)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel ignored (disabled)
azalia0 at pci0 dev 7 function 0: Generic High Definition Audio Controller
LAZA: Picked IRQ 19 with weight 0
azalia0: interrupting at ioapic0 pin 19
azalia0: host: 0x10de/0x055c (rev. 161), HDA rev. 1.0
ppb0 at pci0 dev 8 function 0: vendor 0x10de product 0x0561 (rev. 0xa2)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
fwohci0 at pci1 dev 9 function 0: vendor 0x1180 product 0x0832 (rev. 0x05)
fwohci0: interrupting at ioapic0 pin 10
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 07:e4:0a:00:29:b1:50:47
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x1180 product 0x0822 (SD Host Controller system, revision
0x22) at pci1 dev 9 function 1 not configured
vendor 0x1180 product 0x0592 (miscellaneous system, revision 0x12) at
pci1 dev 9 function 2 not configured
vendor 0x1180 product 0x0852 (miscellaneous system, revision 0x12) at
pci1 dev 9 function 3 not configured
ahcisata0 at pci0 dev 9 function 0: vendor 0x10de product 0x0550
LSI0: Picked IRQ 20 with weight 0
ahcisata0: interrupting at ioapic0 pin 20
ahcisata0: AHCI revision 1.1, 4 ports, 32 command slots, features 0xa3228000
atabus1 at ahcisata0 channel 0
atabus2 at ahcisata0 channel 1
atabus3 at ahcisata0 channel 2
atabus4 at ahcisata0 channel 3
nfe0 at pci0 dev 10 function 0: vendor 0x10de product 0x054c (rev. 0xa2)
LMAC: Picked IRQ 21 with weight 0
nfe0: interrupting at ioapic0 pin 21
nfe0: Ethernet address 00:16:d3:fe:28:b5
ukphy0 at nfe0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x0022, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb1 at pci0 dev 12 function 0: vendor 0x10de product 0x0563 (rev. 0xa2)
ppb1: disabling notification events
pci2 at ppb1 bus 6
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 13 function 0: vendor 0x10de product 0x0563 (rev. 0xa2)
ppb2: disabling notification events
pci3 at ppb2 bus 4
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bwi0 at pci3 dev 0 function 0
LK4E: Picked IRQ 22 with weight 0
bwi0: interrupting at ioapic0 pin 22
bwi0: BBP id 0x4311, BBP rev 0x2, BBP pkg 0
bwi0: MAC rev 13 is not supported
bwi0: no MAC was found
vga0 at pci0 dev 18 function 0: vendor 0x10de product 0x0531 (rev. 0xa2)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
pchb0 at pci0 dev 24 function 0
pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb1 at pci0 dev 24 function 1
pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb2 at pci0 dev 24 function 2
pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3
amdtemp0: AMD CPU Temperature Sensors (K8: core rev BH-G2, socket S1)
isa0 at pcib0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
atapibus0 at atabus0: 2 targets
uhub0 at usb0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 5 ports with 5 removable, self powered
cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T20N, KZ17B2I0705,
WC05> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
acpiacad0: AC adapter online.
azalia0: codec[0]: 0x14f1/0x5045 (rev. 1.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
uhub1 at usb1: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 5 ports with 5 removable, self powered
uhub2 at usb2: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
uhub3 at usb3: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
ahcisata0 port 0: device present, speed: 1.5Gb/s
wd0 at atabus1 drive 0: <ST9120822AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
(Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
hpqlb0: registering on wskbd0
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ubt0 at uhub2 port 3
ubt0: Broadcom Corp HP Integrated Module, rev 2.00/1.00, addr 2
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


Any ideas?

Thank you.

Alexey Lebedev