kern/37963: fxp0: device timeout

[bchavens%gmail.com@localhost]

>Number:         37963
>Category:       kern
>Synopsis:       fxp0: device timeout
>Confidential:   no
>Severity:       non-critical
>Priority:       medium
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Tue Feb 05 17:15:00 +0000 2008
>Originator:     Brian Havens
>Release:        4.0 i386
>Organization:
>Environment:
NetBSD test 4.0 NetBSD 4.0 (GENERIC) #0: Sun Dec 16 00:20:10 PST 2007  
builds@wb34:/home/builds/ab/netbsd-4-0-RELEASE/i386/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC
 i386

>Description:
When configuring an fxp network adapter (intel i82559), the generic kernel 
reports

  fxp0: device timeout

After configuration, the device is unable to send or receive packets over the 
network.

dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0 (GENERIC) #0: Sun Dec 16 00:20:10 PST 2007
        
builds@wb34:/home/builds/ab/netbsd-4-0-RELEASE/i386/200712160005Z-obj/ho 
me/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 511 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 492 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfb3f0
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon XP 2500+ (686-class), 1830.06 MHz, id 0x6a0
cpu0: features c3c3fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3c3fbff<PGE,MCA,CMOV,PAT,PSE36,MMXX,MMX>
cpu0: features c3c3fbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: "AMD Athlon(tm) XP 2500+"
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: AMD Power Management features: 1<TS>
cpu0: calibrating local timer
cpu0: apic clock running at 332 MHz
cpu0: 8 page colors
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <Nvidia,AWRDACPI,42302e31>, AslId <AWRD,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0C01 [System Board] at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
PNP0501 [16550A-compatible COM port] at acpi0 not configured
PNP0400 [Standard LPT printer port] at acpi0 not configured
pckbc1 at acpi0 (PNP0F13): aux port
pckbc1: irq 12
pckbc2 at acpi0 (PNP0303): kbd port
pckbc2: io 0x60,0x64 irq 1
PNP0C0B [ACPI Fan] at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: active cooling level 0: 60.0C
acpitz0: critical 60.0C passive 47.0C
pcppi1: attached to attimer1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: NVIDIA nForce2 Host-PCI Bridge (rev. 0xa2)
agp at pchb0 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 1 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 2 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 3 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 4 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 5 not configured
pcib0 at pci0 dev 1 function 0
pcib0: NVIDIA nForce2 PCI-ISA bridge (rev. 0xa3)
NVIDIA nForce2 SMBus Controller (SMBus serial bus, revision 0xa2) at pci0 dev 1 
function 1 not configured
ohci0 at pci0 dev 2 function 0: NVIDIA nForce2 USB Host Controller (rev. 0xa3)
APCF: Picked IRQ 20 with weight 0
ohci0: interrupting at ioapic0 pin 20 (irq 11)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 2 function 1: NVIDIA nForce2 USB Host Controller (rev. 0xa3)
APCG: Picked IRQ 21 with weight 0
ohci1: interrupting at ioapic0 pin 21 (irq 3)
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0 at pci0 dev 2 function 2: NVIDIA nForce2 USB2 Host Controller (rev. 0xa3)
APCL: Picked IRQ 22 with weight 0
ehci0: interrupting at ioapic0 pin 22 (irq 5)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 4 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NVIDIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
nfe0 at pci0 dev 4 function 0: NVIDIA nForce2 Ethernet (rev. 0xa1)
APCH: Picked IRQ 20 with weight 1
nfe0: interrupting at ioapic0 pin 20 (irq 10)
nfe0: Ethernet address 00:50:8d:fb:16:c5
rlphy0 at nfe0 phy 1: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
NVIDIA nForce2 MCP-T Audio Processing Unit (audio multimedia, revision 0xa2) at 
pci0 dev 5 function 0 not configured
auich0 at pci0 dev 6 function 0: nForce2 MCP-T AC-97 Audio
APCJ: Picked IRQ 21 with weight 1
auich0: interrupting at ioapic0 pin 21 (irq 3)
auich0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
auich0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
ppb0 at pci0 dev 8 function 0: NVIDIA nForce2 PCI-PCI bridge (rev. 0xa3)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
fxp0 at pci1 dev 10 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at ioapic0 pin 18 (irq 11)
fxp0: Ethernet address 00:d0:b7:47:b9:cc
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
viaide0 at pci0 dev 9 function 0
viaide0: NVIDIA nForce2 IDE Controller (rev. 0xa2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
fwohci0 at pci0 dev 13 function 0: NVIDIA nForce2 Firewire Controller (rev. 
0xa3 )
APCM: Picked IRQ 22 with weight 1
fwohci0: interrupting at ioapic0 pin 22 (irq 10)
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:00:50:8d:fc:16:c5
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ppb1 at pci0 dev 30 function 0: NVIDIA nForce2 PCI-PCI Bridge (rev. 0xa2)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
vga1 at pci2 dev 0 function 0: NVIDIA GeForce FX 5600 (rev. 0xa1)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
isa0 at pcib0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
auich0: measured ac97 link rate at 47988 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <WDC WD800JB-00FMA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <LITE-ON COMBO LTC-48161H, , KH0M> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1 at atapibus0 drive 1: <LITE-ON DVDRW LDW-411S, , FS02> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
cd1(viaide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
fxp0: device timeout

>How-To-Repeat:
dhclient fxp0

or

ifconfig fxp0 192.168.12.12 netmask 255.255.255.0
>Fix:
The device works properly with the 4.0 GENERIC.NOACPI kernel.

dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0 (GENERIC.NOACPI) #0: Fri Feb  1 05:23:00 UTC 2008
        
builds%b1.netbsd.org@localhost:/home/builds/ab/netbsd-4-0-RELEASE/i386/20080131121
 
5Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC.NOACP
 I
total memory = 511 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 492 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfb3f0
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon XP 2500+ (686-class), 1830.08 MHz, id 0x6a0
cpu0: features c3c3fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3c3fbff<PGE,MCA,CMOV,PAT,PSE36,MMXX,MMX>
cpu0: features c3c3fbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: "AMD Athlon(tm) XP 2500+"
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 512 KB 64B/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: AMD Power Management features: 1<TS>
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: NVIDIA nForce2 Host-PCI Bridge (rev. 0xa2)
agp at pchb0 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 1 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 2 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 3 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 4 not configured
NVIDIA nForce2 Memory Controller (RAM memory, revision 0xa2) at pci0 dev 0 
funct ion 5 not configured
pcib0 at pci0 dev 1 function 0
pcib0: NVIDIA nForce2 PCI-ISA bridge (rev. 0xa3)
NVIDIA nForce2 SMBus Controller (SMBus serial bus, revision 0xa2) at pci0 dev 1 
function 1 not configured
ohci0 at pci0 dev 2 function 0: NVIDIA nForce2 USB Host Controller (rev. 0xa3)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 2 function 1: NVIDIA nForce2 USB Host Controller (rev. 0xa3)
ohci1: interrupting at irq 3
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ehci0 at pci0 dev 2 function 2: NVIDIA nForce2 USB2 Host Controller (rev. 0xa3)
ehci0: interrupting at irq 5
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 4 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NVIDIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
nfe0 at pci0 dev 4 function 0: NVIDIA nForce2 Ethernet (rev. 0xa1)
nfe0: interrupting at irq 10
nfe0: Ethernet address 00:50:8d:fb:16:c5
rlphy0 at nfe0 phy 1: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
NVIDIA nForce2 MCP-T Audio Processing Unit (audio multimedia, revision 0xa2) at 
pci0 dev 5 function 0 not configured
auich0 at pci0 dev 6 function 0: nForce2 MCP-T AC-97 Audio
auich0: interrupting at irq 3
auich0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
auich0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
ppb0 at pci0 dev 8 function 0: NVIDIA nForce2 PCI-PCI bridge (rev. 0xa3)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
fxp0 at pci1 dev 10 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at irq 11
fxp0: Ethernet address 00:d0:b7:47:b9:cc
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
viaide0 at pci0 dev 9 function 0
viaide0: NVIDIA nForce2 IDE Controller (rev. 0xa2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
fwohci0 at pci0 dev 13 function 0: NVIDIA nForce2 Firewire Controller (rev. 
0xa3 )
fwohci0: interrupting at irq 10
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:00:00:50:8d:fc:16:c5
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ppb1 at pci0 dev 30 function 0: NVIDIA nForce2 PCI-PCI Bridge (rev. 0xa2)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
vga1 at pci2 dev 0 function 0: NVIDIA GeForce FX 5600 (rev. 0xa1)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
isa0 at pcib0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 36083 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <WDC WD800JB-00FMA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <LITE-ON COMBO LTC-48161H, , KH0M> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd1 at atapibus0 drive 1: <LITE-ON DVDRW LDW-411S, , FS02> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
cd1(viaide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)