On Wed, Oct 10, 2001 at 09:45:07PM +0200, Manuel Bouyer wrote:
>
> > When I've built new kernels in the past two weeks, when booting
> > them, it now hangs prompting me for the boot device.  I've not
> > touched the OFW env settings so I think the problem is sw related.
> > I do recall some discussion relating to "boot_dev" settings and
> > RAIDframe support resulting in a change... maybe this broke things
> > for us boring FFS users.  My kernel circa Sept 21st seems to boot fine.
> 
> Hum, I tested this change on regular FFS too.
> Can you post dmesg ?

Can do.  I made sure to do a "binstall -U -v ffs /" when I
first encountered this, thinking the boot block and kernel
may be out of sync.  No change alas.  Here is my dmesg output:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5Y (SS20) #0: Sun Oct  7 13:41:50 EDT 2001
    kwellsch@ss20:/usr/src/sys/arch/sparc/compile/SS20
total memory = 31980 KB
avail memory = 27528 KB
using 425 buffers containing 1700 KB of memory
bootpath: /iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000/sd@3,0
mainbus0 (root): SUNW,SPARCstation-20
cpu0 at mainbus0: TMS390Z50 v0 or TMS390Z55 @ 60 MHz, on-chip FPU
cpu0: physical 20K instruction (64 b/l), 16K data (32 b/l), 1024K external (32 b
/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x200000: mk48t08: hostid 72729adc
timer0 at obio0 slot 0 offset 0x300000 delay constant 28
zs0 at obio0 slot 0 offset 0x100000 level 12 softpri 6
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
kbd0 at zs1 channel 0: baud rate 1200 (console input)
ms0 at zs1 channel 1: baud rate 1200
fdc0 at obio0 slot 0 offset 0x700000 level 11 softpri 4: chip 82077
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
auxreg0 at obio0 slot 0 offset 0x800000
power0 at obio0 slot 0 offset 0xa01000 level 2
iommu0 at mainbus0 ioaddr 0xe0000000: version 0x3/0x1, page-size 4096, range 64M
B
sbus0 at iommu0: clock = 25 MHz
dma0 at sbus0 slot 15 offset 0x400000: dma rev 2
esp0 at dma0 slot 15 offset 0x800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
ledma0 at sbus0 slot 15 offset 0x400010: dma rev 2
le0 at ledma0 slot 15 offset 0xc00000 level 6: address 08:00:20:72:9a:dc
le0: 8 receive buffers, 2 transmit buffers
bpp0 at sbus0 slot 15 offset 0x4800000 level 2 (ipl 3): dma rev 2
SUNW,DBRIe at sbus0 slot 14 offset 0x10000 level 9 not configured
cgsix0 at sbus0 slot 2 offset 0x0 level 9: SUNW,501-2325, 1152 x 900, rev 11 (co
nsole)
cgsix0: attached to /dev/fb
eccmemctl0 at mainbus0: version 0x0/0x2
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <SEAGATE, ST32151W, 0526> SCSI2 0/direct fixed
sd0: 2049 MB, 4177 cyl, 8 head, 125 sec, 512 bytes/sect x 4197405 sectors
sd0: sync (100.0ns offset 15), 8-bit (10.000MB/s) transfers, tagged queueing
root device: sd0
dump device (default sd0b): 
file system (default generic): 
root on sd0a dumps on sd0b
root file system type: ffs