Re: netbsd i386 works with vortex86mx processor

To: Topiarz <topiarz%post.cz@localhost>, netbsd-users%NetBSD.org@localhost, netbsd-advocacy%netbsd.org@localhost
Subject: Re: netbsd i386 works with vortex86mx processor
From: SAITOH Masanobu <msaitoh%execsw.org@localhost>
Date: Fri, 29 Aug 2014 01:55:25 +0900
On 2014/08/28 19:15, Topiarz wrote:
> Hi folks,
> while current Linux supports mainly i686 only (and that
> makes it not start kernel on vortex86), the NetBSD support
> for i486 is enough to bring machines with vortex86 CPU to
> life. I bought one for a mail server and another one as a
> musicbox with mpd. however I tested it with X and it worked
> flawlessly, I was able to install gnome2 full desktop and
> use it  (I could even watch avis and xvids, though it was
> too slow for flash) on a 993Mhz vortex86mx. Thanks for your
> marvelous work.
> Petr Topiarz aka Kolaloka

 NetBSD supports Vortex86"EX", too.

 For example I have both 86duino ONE and 86duino EduCake and
they work.

http://www.86duino.com/

Currently it doesn't support GPIO... I'd like to control EduCake's
GPIO pins! PLEASE_SOMEONE_WRITE_THE_DRIVER!!!

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.49 (EDUCAKE) #15: Tue Aug 12 23:30:08 JST 2014
        
msaitoh%xxx.execsw.org@localhost:/disk/sources/9NetBSD-current/src/sys/arch/i386/compile/EDUCAKE
total memory = 127 MB
avail memory = 112 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
DMP Vortex86EX (1.0)
mainbus0 (root)
cpu0 at mainbus0: Vortex86EX, id 0x601
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x17f3 product 0x6025 (rev. 0x01)
ppb0 at pci0 dev 1 function 0: vendor 0x17f3 product 0x1031 (rev. 0x02)
ppb0: PCI Express 1.0 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5Gb/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
pcib0 at pci0 dev 7 function 0: vendor 0x17f3 product 0x6011 (rev. 0x01)
pcib1 at pci0 dev 7 function 1: vendor 0x17f3 product 0x6011 (rev. 0x01)
vte0 at pci0 dev 8 function 0: vendor 0x17f3 product 0x6040 (rev. 0x00)
vte0: Ethernet address 00:1b:eb:51:95:0d
vte0: interrupting at irq 9
ukphy0 at vte0 phy 1: OUI 0x00d02d, model 0x0005, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0 at pci0 dev 10 function 0: vendor 0x17f3 product 0x6060 (rev. 0x13)
ohci0: interrupting at irq 14
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 10 function 1: vendor 0x17f3 product 0x6061 (rev. 0x07)
ehci0: interrupting at irq 10
ehci0: EHCI version 1.0
ehci0: companion controller, 2 ports each: ohci0
usb1 at ehci0: USB revision 2.0
rdcide0 at pci0 dev 12 function 0: RDC R1012 IDE controller (rev. 0x03)
rdcide0: bus-master DMA support present
rdcide0: primary channel configured to native-PCI mode
rdcide0: using irq 11 for native-PCI interrupt
atabus0 at rdcide0 channel 0
rdcide0: secondary channel configured to native-PCI mode
rdcide0: secondary channel ignored (disabled)
hdaudio0 at pci0 dev 14 function 0: HD Audio Controller
hdaudio0: interrupting at irq 7
hdafg0 at hdaudio0: Realtek ALC262
hdafg0: DAC00 2ch: Speaker [Jack]
hdafg0: DIG01 2ch: Digital Out [Jack]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: ADC03 2ch: Line In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
vendor 0x17f3 product 0x1060 (USB serial bus, device, revision 0x03) at pci0 
dev 15 function 0 not configured
vendor 0x17f3 product 0x1331 (undefined, subclass 0xff) at pci0 dev 16 function 
0 not configured
vendor 0x17f3 product 0x1710 (undefined, subclass 0xff, revision 0x01) at pci0 
dev 16 function 1 not configured
vendor 0x17f3 product 0x1070 (CANbus serial bus) at pci0 dev 17 function 0 not 
configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
com2 at isa0 port 0x3e8-0x3ef irq 5: ns16550a, working fifo
com3 at isa0 port 0x2e8-0x2ef irq 12: ns16550a, working fifo
com3: console
pckbc0 at isa0 port 0x60-0x64
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
pcic: does not support memory and I/O cards, ignored (ident=3)
pcic: does not support memory and I/O cards, ignored (ident=3)
pcic: does not support memory and I/O cards, ignored (ident=3)
pcic: does not support memory and I/O cards, ignored (ident=3)
attimer0: attached to pcppi0
isa at pcib1 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x17f3 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x17f3 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
wd0 at atabus0 drive 0
IPsec: Initialized Security Association Processing.
wd0: <SP16G D0 RDC SD-IDE HOST CONTROLLER>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 15193 MB, 30869 cyl, 16 head, 63 sec, 512 bytes/sect x 31116288 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(rdcide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) 
(using DMA)
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
clock: unknown CMOS layout




> here is dmesg:
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002,
> 2003, 2004, 2005,
>     2006, 2007, 2008, 2009, 2010, 2011, 2012
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights
> reserved.
> 
> NetBSD 6.1.4 (GENERIC)
> total memory = 511 MB
> avail memory = 490 MB
> timecounter: Timecounters tick every 10.000 msec
> timecounter: Timecounter "i8254" frequency 1193182 Hz
> quality 100
> Generic PC
> mainbus0 (root)
> acpi_probe: failed to initialize tables
> cpu0 at mainbus0: Vortex86MX, id 0x586
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o space, memory space enabled, rd/line, rd/mult,
> wr/inv ok
> pchb0 at pci0 dev 0 function 0: vendor 0x17f3 product 0x6021
> (rev. 0x02)
> rdcpcib0 at pci0 dev 7 function 0: vendor 0x17f3 product
> 0x6036 (rev. 0x00)
> rdcpcib0: watchdog timer configured.
> vte0 at pci0 dev 8 function 0: vendor 0x17f3 product 0x6040
> (rev. 0x00)
> vte0: Ethernet address 00:1b:eb:62:a6:34
> vte0: interrupting at irq 5
> rdcphy0 at vte0 phy 1: R6040 10/100 media interface, rev. 1
> rdcphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> ohci0 at pci0 dev 10 function 0: vendor 0x17f3 product
> 0x6060 (rev. 0x12)
> ohci0: interrupting at irq 9
> ohci0: OHCI version 1.0, legacy support
> usb0 at ohci0: USB revision 1.0
> ehci0 at pci0 dev 10 function 1: vendor 0x17f3 product
> 0x6061 (rev. 0x03)
> ehci0: interrupting at irq 9
> ehci0: BIOS has given up ownership
> ehci0: EHCI version 1.0
> ehci0: companion controller, 2 ports each: ohci0
> usb1 at ehci0: USB revision 2.0
> ohci1 at pci0 dev 11 function 0: vendor 0x17f3 product
> 0x6060 (rev. 0x12)
> ohci1: interrupting at irq 9
> ohci1: OHCI version 1.0, legacy support
> usb2 at ohci1: USB revision 1.0
> ehci1 at pci0 dev 11 function 1: vendor 0x17f3 product
> 0x6061 (rev. 0x03)
> ehci1: interrupting at irq 9
> ehci1: BIOS has given up ownership
> ehci1: EHCI version 1.0
> ehci1: companion controller, 2 ports each: ohci1
> usb3 at ehci1: USB revision 2.0
> rdcide0 at pci0 dev 12 function 0: RDC IDE controller (rev.
> 0x01)
> rdcide0: bus-master DMA support present
> rdcide0: primary channel configured to compatibility mode
> rdcide0: primary channel interrupting at irq 14
> atabus0 at rdcide0 channel 0
> rdcide0: secondary channel configured to compatibility mode
> rdcide0: secondary channel interrupting at irq 15
> atabus1 at rdcide0 channel 1
> vga1 at pci0 dev 13 function 0: vendor 0x17f3 product 0x2010
> (rev. 0x00)
> wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
> wsmux1: connecting to wsdisplay0
> drm at vga1 not configured
> hdaudio0 at pci0 dev 14 function 0: HD Audio Controller
> hdaudio0: interrupting at irq 10
> hdafg0 at hdaudio0: Realtek ALC262
> hdafg0: DAC00 2ch: Speaker [Jack]
> hdafg0: ADC01 2ch: Mic In [Jack]
> hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20
> PCM24 AC3
> audio0 at hdafg0: full duplex, playback, capture, independent
> isa0 at rdcpcib0
> pckbc0 at isa0 port 0x60-0x64
> pckbd0 at pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> attimer0 at isa0 port 0x40-0x43
> pcppi0 at isa0 port 0x61
> midi0 at pcppi0: PC speaker
> sysbeep0 at pcppi0
> isapnp0 at isa0 port 0x279
> npx0 at isa0 port 0xf0-0xff
> npx0: reported by CPUID; using exception 16
> attimer0: attached to pcppi0
> isapnp0: no ISA Plug 'n Play devices found
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz
> quality 0
> uhub0 at usb0: vendor 0x17f3 OHCI root hub, class 9/0, rev
> 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub1 at usb1: vendor 0x17f3 EHCI root hub, class 9/0, rev
> 2.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhub2 at usb2: vendor 0x17f3 OHCI root hub, class 9/0, rev
> 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhub3 at usb3: vendor 0x17f3 EHCI root hub, class 9/0, rev
> 2.00/1.00, addr 1
> uhub3: 2 ports with 2 removable, self powered
> uhidev0 at uhub0 port 2 configuration 1 interface 0
> uhidev0: vendor 0x1267 PS/2+USB Mouse, rev 1.10/51.15, addr
> 2, iclass 3/1
> ums0 at uhidev0: 3 buttons and Z dir
> wsmouse0 at ums0 mux 0
> wd0 at atabus1 drive 0
> wd0: <WDC WD2500BPVT-00ZEST0>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x
> 488397168 sectors
> wd0: 32-bit data port
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6
> (Ultra/133)
> wd0(rdcide0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA
> mode 2 (Ultra/33) (usng DMA)
> Kernelized RAIDframe activated
> boot device: wd0
> root on wd0a dumps on wd0b
> root file system type: ffs
> wsdisplay0: screen 1 added (80x25, vt100 emulation)
> wsdisplay0: screen 2 added (80x25, vt100 emulation)
> wsdisplay0: screen 3 added (80x25, vt100 emulation)
> wsdisplay0: screen 4 added (80x25, vt100 emulation)
> 


-- 
-----------------------------------------------
                SAITOH Masanobu (msaitoh%execsw.org@localhost
                                 msaitoh%netbsd.org@localhost)
References:
- netbsd i386 works with vortex86mx processor
  - From: Topiarz
Prev by Date: netbsd i386 works with vortex86mx processor
Next by Date: Re: netbsd i386 works with vortex86mx processor
Previous by Thread: netbsd i386 works with vortex86mx processor
Next by Thread: Re: netbsd i386 works with vortex86mx processor
Indexes:
Home | Main Index | Thread Index | Old Index