>> No, this still doesn't work for me.  Suspend seems to
>> work, and then I press the power button or space key,
>> hard disk spins few seconds, stops, and system hangs up.
>> The caps key doesn't toggle LED.
> 
> Can you please post a dmesg?

Yes, this is it!


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.27 (GENERIC) #85: Thu Aug  9 07:08:36 EDT 2007
	jmcneill@silver.invisible.ca:/export/home/jmcneill/branches/jmcneill-pm/src/sys/arch/i386/compile/GENERIC
total memory = 239 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 224 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd740
SMBIOS rev. 2.31 @ 0xdc010 (16 entries)
Sony Corporation PCG-U1(J) (01)
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Transmeta Crusoe (586-class), 860.28 MHz, id 0x543
cpu0: Processor revision 1.4.1.0
cpu0: Code Morphing Software Rev: 4.3.0-9-197
cpu0: 20020207 23:55 official release 4.3.0#7
cpu0: LongRun mode: 2  <867MHz 1300mV 100%>
cpu0: features 84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP>
cpu0: features 84893f<CMOV,PN,MMX>
cpu0: "Transmeta(tm) Crusoe(tm) Processor TM5800"
cpu0: serial number 0000-0543-0000-42BC-00A5-55C2
cpu0: generic device class power management enabled
cpu0: supported states: D0 D3
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <SONY  ,E0      ,20020312>, AslId < LTP,00000000>
acpi0: generic device class power management enabled
acpi0: supported states: D0 D3
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 32-bit timer
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNK8: ACPI: Found matching pin for 0.6.INTA at func 0: 255
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNK2: ACPI: Found matching pin for 0.9.INTA at func 0: 9
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNK3: ACPI: Found matching pin for 0.11.INTA at func 0: 9
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNK1: ACPI: Found matching pin for 0.12.INTA at func 0: 9
acpi_pci_link: WARNING: powerhook_establish is deprecated
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNK5: ACPI: Found matching pin for 0.15.INTA at func 0: 255
LNK3: ACPI: Found matching pin for 0.18.INTA at func 0: 255
acpi_pci_link: WARNING: powerhook_establish is deprecated
LNKU: ACPI: Found matching pin for 0.20.INTA at func 0: 9
CPU0 (ACPI Object Type 'Processor' [0x0c]) at acpi0 not configured
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpilid0: generic device class power management enabled
acpilid0: supported states: D0 D3
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpibut0: generic device class power management enabled
acpibut0: supported states: D0 D3
PCI0 (PNP0A03) [PCI/PCI-X Host Bridge] at acpi0 not configured
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpiec0: generic device class power management enabled
acpiec0: supported states: D0 D3
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: generic device class power management enabled
acpibat0: supported states: D0 D3
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpiacad0: generic device class power management enabled
acpiacad0: supported states: D0 D3
sony0 at acpi0 (SNC, SNY5001): Sony Miscellaneous Controller
sony0: generic device class power management enabled
sony0: supported states: D0 D3
wskbd at sony0 not configured
DMAC (PNP0200) [AT DMA Controller] at acpi0 not configured
PIC (PNP0000) [AT Interrupt Controller] at acpi0 not configured
attimer1 at acpi0 (TIME, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
attimer1: generic device class power management enabled
attimer1: supported states: D0 D3
RTC (PNP0B00) [AT Real-Time Clock] at acpi0 not configured
npx1 at acpi0 (MATH, PNP0C04)
npx1: io 0xf0-0xfe irq 13
npx1: reported by CPUID; using exception 16
npx1: generic device class power management enabled
npx1: supported states: D0 D3
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
midi0: WARNING: power management not supported
sysbeep0 at pcppi1
sysbeep0: WARNING: power management not supported
pcppi1: WARNING: power management not supported
pckbc1 at acpi0 (KBC0, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc1: generic device class power management enabled
pckbc1: supported states: D0 D3
pckbc2 at acpi0 (MSE0, SNY9004): aux port
pckbc2: irq 12
pckbc2: generic device class power management enabled
pckbc2: supported states: D0 D3
SYSR (PNP0C02) [Plug and Play motherboard register resources] at acpi0 not configured
LNK1 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNK2 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNK3 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNK4 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNK5 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNK8 (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LNKU (PNP0C0F) [PCI interrupt link device] at acpi0 not configured
LRP0 (ACPI Object Type 'Power' [0x0b]) at acpi0 not configured
LRA0 (PNP0C0B) [ACPI Fan] at acpi0 not configured
acpitz0 at acpi0 (ATF0): ACPI Thermal Zone
acpitz0: active cooling level 0: 78.9C
acpitz0: critical 89.9C
acpitz0: generic device class power management enabled
acpitz0: supported states: D0 D3
apm0 at acpi0: Power Management spec V1.2
acpibat0: battery info: Sony Corp., LION,
acpiacad0: AC adapter online.
apm0: generic device class power management enabled
apm0: supported states: D0 D3
pcppi1: attached to attimer1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
pckbd0: generic device class power management enabled
pckbd0: supported states: D0 D1 D3
wskbd0 at pckbd0: console keyboard
wskbd0: generic device class power management enabled
wskbd0: supported states: D0 D3
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
wsmouse0: generic device class power management enabled
wsmouse0: supported states: D0 D3
pms0: generic device class power management enabled
pms0: supported states: D0 D3
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pci0: generic device class power management enabled
pci0: supported states: D0 D3
pchb0 at pci0 dev 0 function 0
pchb0: Transmeta LongRun Northbridge (rev. 0x02)
pchb0: generic device class power management enabled
pchb0: supported states: D0 D3
Transmeta SDRAM Controller (RAM memory) at pci0 dev 0 function 1 not configured
Transmeta BIOS Scratchpad (RAM memory) at pci0 dev 0 function 2 not configured
autri0 at pci0 dev 6 function 0: Acer Labs M5451 AC-Link Controller Audio Device (rev. 0x02)
autri0: interrupting at irq 9
autri0: ac97: Yamaha YMF753-S codec; 18 bit DAC, no 3D stereo
audio0 at autri0: full duplex, mmap, independent
audio0: audio device class power management enabled
audio0: supported states: D0 D3
midi1 at autri0: 4DWAVE MIDI UART (CPU-intensive output)
midi1: WARNING: power management not supported
autri0: WARNING: powerhook_establish is deprecated
autri0: WARNING: power management not supported
pcib0 at pci0 dev 7 function 0
pcib0: Acer Labs M1533 PCI-ISA Bridge (rev. 0x00)
pcib0: generic device class power management enabled
pcib0: supported states: D0 D3
fwohci0 at pci0 dev 9 function 0: Texas Instruments TSB43AA22/A IEEE 1394 Host Controller (rev. 0x00)
fwohci0: interrupting at irq 9
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 08:00:46:03:01:1b:be:0c
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: WARNING: powerhook_establish is deprecated
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwip0: WARNING: power management not supported
fwohci0: Initiate bus reset
ieee1394if0: WARNING: power management not supported
fwohci0: WARNING: power management not supported
rtk0 at pci0 dev 11 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at irq 9
rtk0: WARNING: powerhook_establish is deprecated
rtk0: Ethernet address 08:00:46:63:4d:c9
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rlphy0: WARNING: power management not supported
rtk0: WARNING: powerhook_establish is deprecated
rtk0: WARNING: power management not supported
vga1 at pci0 dev 12 function 0: ATI Technologies Radeon Mobility M6 LY (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
wsdisplay0: generic device class power management enabled
wsdisplay0: supported states: D0 D3
vga1: display device class power management enabled
vga1: supported states: D0 D3
direct rendering for vga1 unsupported
ohci0 at pci0 dev 15 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
ohci0: can't map mem space
ohci0: WARNING: power management not supported
aceride0 at pci0 dev 16 function 0
aceride0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc4)
aceride0: bus-master DMA support present
aceride0: primary channel wired to compatibility mode
aceride0: primary channel interrupting at irq 14
atabus0 at aceride0 channel 0
atabus0: generic device class power management enabled
atabus0: supported states: D0 D1 D3
aceride0: secondary channel wired to compatibility mode
aceride0: secondary channel ignored (disabled)
aceride0: WARNING: power management not supported
Acer Labs M7101 Power Management Controller (miscellaneous prehistoric) at pci0 dev 17 function 0 not configured
cbb0 at pci0 dev 18 function 0: Ricoh 5C475 PCI-CardBus bridge (rev. 0x80)
cbb0: WARNING: power management not supported
ohci1 at pci0 dev 20 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
ohci1: interrupting at irq 9
ohci1: OHCI version 1.0, legacy support
ohci1: WARNING: powerhook_establish is deprecated
usb0 at ohci1: USB revision 1.0
uhub0 at usb0
uhub0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: generic device class power management enabled
uhub0: supported states: D0 D3
usb0: WARNING: power management not supported
ohci1: WARNING: power management not supported
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: generic device class power management enabled
isapnp0: supported states: D0 D3
isa0: generic device class power management enabled
isa0: supported states: D0 D3
isapnp0: no ISA Plug 'n Play devices found
cbb0: interrupting at irq 9
cbb0: WARNING: powerhook_establish is deprecated
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1
cardbus0: WARNING: power management not supported
pcmcia0 at cardslot0
pcmcia0: WARNING: power management not supported
cardslot0: WARNING: power management not supported
mainbus0: generic device class power management enabled
mainbus0: supported states: D0 D3
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
Kernelized RAIDframe activated
wd0 at atabus0 drive 0: <TOSHIBA MK2003GAH>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19073 MB, 38752 cyl, 16 head, 63 sec, 512 bytes/sect x 39062520 sectors
wd0: WARNING: power management not supported
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(aceride0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs

-- 
iKAWAMOTO Yosihisa!
                   kawamoto@tenjin.org