Recent changes in current to fix the pd6729 pcmcia bridge code and
tidy up the wi code have had a positive effect regarding PR 14057 and
it is possible a Compaq WL200 wireless card may soon work. This is
real step forward as this card causes Generic kernels to hang under 1.6
and 2.0.

The card appears to be detected now and it is possible to ifconfig it up
and it looks like it can see an access point. However wiconfig fails to scan
for access points and ifconfig reports a status of no network. I would really
like to get this card working, but am not really familiar with the wireless
code.

The kernel boot messages and some diagnostics are below. If I issue
wiconfig wi0 immediately after a reboot:

# wiconfig wi0
NIC serial number:			[  ]
Station name:				[  ]
SSID for IBSS creation:			[  ]
Current netname (SSID):			[  ]
Desired netname (SSID):			[  ]
Current BSSID:				[ 00:00:00:00:00:00 ]
Channel list:				[ 1 2 3 4 5 6 7 8 9 10 11 12 13 ]
IBSS channel:				[ 3 ]
Current channel:			[ 65535 ]
Comms quality/signal/noise:		[ 0 0 0 ]
Promiscuous mode:			[ Off ]
Port type:				[ 1 ]
MAC address:				[ 00:50:8b:d0:39:e5 ]
TX rate (selection):			[ 0 ]
TX rate (actual speed):			[ 0 ]
Beacon Interval (current) [msec]:	[ 0 ]
Maximum data length:			[ 2304 ]
RTS/CTS handshake threshold:		[ 2347 ]
fragmentation threshold:		[ 2346 ]
RSSI -> dBm adjustment:			[ 100 ]
Create IBSS:				[ Off ]
Microwave oven robustness:		[ 0 ]
Roaming mode(1:firm,3:disable):		[ 1 ]
Access point density:			[ 1 ]
Power Mgmt (1=on, 0=off):		[ 0 ]
Max sleep time (msec):			[ 100 ]
Vendor info:
WEP encryption:				[ Off ]
Authentication type
(1=OpenSys, 2=Shared Key):		[ 1 ]
TX encryption key:			[ 1 ]
Encryption keys:			[  ][  ][  ][  ]

ifconfig wi0 shows:

wi0: flags=8822<BROADCAST,NOTRAILERS,SIMPLEX,MULTICAST> mtu 1500
	ssid ""
	powersave off
	address: 00:50:8b:d0:39:e5
	media: IEEE802.11 autoselect (none)

Bringing up the interface and repeating the wiconfig command shows:

wi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ssid ""
	powersave off
	address: 00:50:8b:d0:39:e5
	media: IEEE802.11 autoselect (DS2)
	status: no network
	inet6 fe80::250:8bff:fed0:39e5%wi0 prefixlen 64 scopeid 0x9

# wiconfig wi0
NIC serial number:			[ 99SA01000000 ]
Station name:				[  ]
SSID for IBSS creation:			[  ]
Current netname (SSID):			[ UoL RoamNet ]
Desired netname (SSID):			[  ]
Current BSSID:				[ 00:0c:41:de:09:07 ]
Channel list:				[ 1 2 3 4 5 6 7 8 9 10 11 12 13 ]
IBSS channel:				[ 3 ]
Current channel:			[ 6 ]
Comms quality/signal/noise:		[ 0 25 0 ]
Promiscuous mode:			[ Off ]
Port type:				[ 1 ]
MAC address:				[ 00:50:8b:d0:39:e5 ]
TX rate (selection):			[ 0 ]
TX rate (actual speed):			[ 2 ]
Beacon Interval (current) [msec]:	[ 100 ]
Maximum data length:			[ 2304 ]
RTS/CTS handshake threshold:		[ 2347 ]
fragmentation threshold:		[ 2346 ]
RSSI -> dBm adjustment:			[ 100 ]
Create IBSS:				[ Off ]
Microwave oven robustness:		[ 0 ]
Roaming mode(1:firm,3:disable):		[ 1 ]
Access point density:			[ 1 ]
Power Mgmt (1=on, 0=off):		[ 0 ]
Max sleep time (msec):			[ 100 ]
Vendor info:				[ Unknown ID: 31 version: 0.8 ]
WEP encryption:				[ Off ]
Authentication type
(1=OpenSys, 2=Shared Key):		[ 1 ]
TX encryption key:			[ 1 ]
Encryption keys:			[  ][  ][  ][  ]

It looks like the local AP with netname "Uol RoamNet" has been seen. But if I
issue a wiconfig wi0 -D it reports:

#wiconfig wi0 -D
scanning ........
No APs available

Occasionally I see command failed messages from the wi driver:

Jul 23 17:28:32 xxx /netbsd: wi0: command failed, cmd=0x11, arg=0xf101

Setting  wi_debug=2 and issuing the wiconfig wi0 -D shows:

Jul 23 17:58:06 xxx /netbsd: pcmcia0: card irq 5
Jul 23 17:58:07 xxx /netbsd: wi_reset
Jul 23 17:58:07 xxx /netbsd: wi_init: return 0
Jul 23 17:58:07 xxx /netbsd: wi_scan_ap: start scanning, chanmask 0x3fff txrate 0xf
Jul 23 17:58:09 xxx /netbsd: wi_watchdog: inquire scan
Jul 23 17:58:11 xxx last message repeated 2 times
Jul 23 17:58:12 xxx /netbsd: wi_stop: disable 1

Any suggestions as to where to put probes in the source code to try and fix
this would be appreciated.

Dave

Full dmesg:

NetBSD 2.0G (TEST) #7: Tue Jul 27 11:19:05 BST 2004
	root@xxx.liv.ac.uk:/usr/src/sys/arch/i386/compile/TEST
total memory = 254 MB
avail memory = 242 MB
BIOS32 rev. 0 found at 0xfd880
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium III (686-class), 731.01 MHz, id 0x683
cpu0: features 387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 387f9ff<PGE,MCA,CMOV,PAT,PSE36,PN,MMX>
cpu0: features 387f9ff<FXSR,SSE>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 8-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: serial number 0000-0683-0000-16CF-EBDA-EED0
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82810E Memory Controller Hub (rev. 0x03)
pchb0: random number generator enabled
agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
vga1 at pci0 dev 1 function 0: Intel 82810E Graphics Controller (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
ppb0 at pci0 dev 30 function 0: Intel 82801AA Hub-to-PCI Bridge (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
pcic0 at pci1 dev 9 function 0: Cirrus Logic PD6729 PCMCIA controller
pcic0: controller 0 (Cirrus PD6710/2X) has sockets A and B
fxp0 at pci1 dev 11 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at irq 9
fxp0: Ethernet address 00:d0:b7:49:ee:da
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcmcia0 at pcic0 controller 0 socket 0
pcmcia1 at pcic0 controller 0 socket 1
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801AA LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801AA IDE Controller (ICH) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 31 function 2: Intel 82801AA USB Controller (rev. 0x02)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82801AA SMBus Controller (SMBus serial bus, revision 0x02) at pci0 dev 31 function 3 not configured
auich0 at pci0 dev 31 function 5: i82801AA (ICH) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: Analog Devices AD1881A codec; headphone, Analog Devices Phat Stereo
auich0: ac97: ext id 1<VRA>
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
pcic0: using irq 3 for socket events
auich0: measured ac97 link rate at 47270 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
fdcintr: got probe interrupt
fdcintr: got probe interrupt
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
fdcintr: got probe interrupt
raidattach: Asked for 8 units
Kernelized RAIDframe activated
pcmcia0: CIS version PC Card Standard 5.0
pcmcia0: CIS info: Compaq, WL200_11Mbps_Wireless_PCI_Card, ,
pcmcia0: Manufacturer code 0x138, product 0x2
pcmcia0: function 0: network adapter, ccr addr 3e0 mask 1
pcmcia0: function 0, config table entry 1: I/O card; irq mask 0; iomask 6, iospace 0-3f; io16
wi0 at pcmcia0 function 0: <Compaq, WL200_11Mbps_Wireless_PCI_Card, >
pcic0: port 0x400-0x43f
pcmcia0: card irq 5
wi0: 802.11 address 00:50:8b:d0:39:e5
wi0: using RF:PRISM2 MAC:HFA3841 CARD:HWB3163 rev.A
wi0: Intersil Firmware: Primary (0.3.0), Station (0.8.0)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wd0 at atabus0 drive 0: <FUJITSU MPE3064AT>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 6187 MB, 13410 cyl, 15 head, 63 sec, 512 bytes/sect x 12672450 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <CRD-8480M, 1999/08/23, 1.01> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
Searching for RAID components...
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying nfs...
mountroot: trying ffs...
root file system type: ffs
init: copying out path `/sbin/init' 11
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

--
=====================================================================
Computing Services Dept         Phone/Fax: 0151-794-3731/3759
The University of Liverpool     Email: dtyson@liv.ac.uk
Chadwick Tower, Peach Street    WWW:   http://www.liv.ac.uk/~dtyson
Liverpool L69 7ZF               Open Source O/S: www.netbsd.org
=====================================================================