Hey Everyone,

ZE hangs during boot, as shown below. Following [EOT] is the dmesg from
my last sucessful boot. 

connected

>> NetBSD/i386 BIOS Boot, Revision 2.13
>> (autobuild@tgm.daemon.org, Tue Apr  8 11:27:33 UTC 2003)
>> Memory: 639/523248 k
> boot
booting hd0a:netbsd
[masses of loader junk removed]
BIOS CFG: Model-SubM-Rev: fc-01-00, 0x74<EBDA,KBDINT,RTC,IC2>
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.6ZE (GENERIC) #1: Sun Nov  2 13:05:01 MST 2003
	bjan@telstar.bjan.net:/usr/obj/sys/arch/i386/compile/GENERIC
total memory = 511 MB
avail memory = 466 MB
using 6144 buffers containing 26296 KB of memory
BIOS32 rev. 0 found at 0xf16f0
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD Athlon XP 2100+ (686-class), 1300.12 MHz, id 0x681
cpu0: features c3c3fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3c3fbff<PGE,MCA,CMOV,PAT,PSE36,MMXX,MMX>
cpu0: features c3c3fbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: 8 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT8377 Apollo KT400 CPU to PCI Bridge (rev. 0x00)
agp0 at pchb0: aperture at 0xf8000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: VIA Technologies VT8377 CPU-AGP Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: ATI Technologies Radeon 7500 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
VIA Technologies VT3606 OHCI IEEE 1394 Controller (Firewire serial bus, interface 0x10, revision 0x80) at pci0 dev 7 function 0 not configured
pdcide0 at pci0 dev 8 function 0
pdcide0: Promise Serial ATA/150 TX2plus Bus Master IDE Accelerator (rev. 0x02)
pdcide0: bus-master DMA support present
pdcide0: primary channel configured to compatibility mode
pdcide0: primary channel ignored (disabled)
pdcide0: secondary channel configured to compatibility mode
pdcide0: secondary channel ignored (disabled)
bge0 at pci0 dev 9 function 0: Broadcom BCM5702X Gigabit Ethernet
bge0: interrupting at irq 5
bge0: ASIC BCM5703 A2, Ethernet address 00:e0:18:d2:a2:8a
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
puc0 at pci0 dev 10 function 0: SIIG Cyber 2S1P PCI 16C550 (10x family) (com, com, lpt)
com3 at puc0 port 0: interrupting at irq 11
com3: ns16550a, working fifo
com4 at puc0 port 1: interrupting at irq 11
com4: ns16550a, working fifo
lpt3 at puc0 port 2: interrupting at irq 11
ATI Technologies Rage XL (VGA display, revision 0x27) at pci0 dev 11 function 0 not configured
Atheros Communications, Inc. AR5212 Wireless LAN (ethernet network, revision 0x01) at pci0 dev 13 function 0 not configured
uhci0 at pci0 dev 16 function 0: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci0: interrupting at irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 16 function 1: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 16 function 2: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
VIA Technologies VT8237 EHCI USB Controller (USB serial bus, interface 0x20, revision 0x82) at pci0 dev 16 function 3 not configured
pcib0 at pci0 dev 17 function 0
pcib0: VIA Technologies VT8235 (Apollo KT400) PCI-ISA Bridge (rev. 0x00)
viaide0 at pci0 dev 17 function 1
viaide0: VIA Technologies VT8235 ATA133 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
auvia0 at pci0 dev 17 function 5: VIA VT8235 AC'97 Audio (rev 0x50)
auvia0: interrupting at irq 9
auvia0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
auvia0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
audio0 at auvia0: full duplex, mmap, independent
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
com1: console
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
wskbd0: connecting to wsdisplay0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <CD-RW IDE5224, , VER 001> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0 at atabus0 drive 0: <WDC WD300BB-00AUA1>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28629 MB, 58168 cyl, 16 head, 63 sec, 512 bytes/sect x 58633344 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
cd0(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
uhub0: port error, restarting port 1
uhub0: port error, restarting port 2
uhub2: port error, restarting port 1
atapibus1 at atabus1: 2 targets
cd1 at atapibus1 drive 0: <HITACHI DVD-ROM GD-2500, , 0101> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2
sd0 at atapibus1 drive 1: <IOMEGA  ZIP 100       ATAPI, , 23.D> disk removable
sd0: drive offline
sd0: 32-bit data port
cd1(viaide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
sd0(viaide0:1:1): using PIO mode 3
uhub3 at uhub1 port 1umass0 at uhub2 port 2 configuration 1 interface 0
umass0: Genesys Logic USB TO IDE, rev 2.00/0.02, addr 2
umass0: using SCSI over Bulk-Only

uhub3: MCT Corporation. MCT4U, class 9/0, rev 1.00/1.01, addr 2
scsibus0 at umass0: 2 targets, 1 lun per target
sd1 at scsibus0 target 0 lun 0: <IC25N040, ATCS04-0, 0811> disk fixed
uhub3: 5 ports with 4 removable, self powered
sd1: fabricating a geometry
sd1: 38154 MB, 38154 cyl, 64 head, 32 sec, 512 bytes/sect x 78140160 sectors
uhub4 at uhub3 port 1
uhub4: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00, addr 3
uhub4: 4 ports with 4 removable, self powered
ulpt0 at uhub3 port 3 configuration 1 interface 0
ulpt0: EPSON USB Printer, rev 1.10/1.00, addr 4, iclass 7/1
ulpt0: using bi-directional mode
uscanner0 at uhub3 port 5
uscanner0: Color FlatbedScanner 13, rev 1.00/1.00, addr 5
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: PCally Peripherals PCally USB & PS/2 Optical Internet Mouse, rev 1.10/0.01, addr 6, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
wd0: transfer error, downgrading to Ultra-DMA mode 2
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
cd0(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
wd0d: error reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0: (aborted command, interface CRC error)
~Stopped at      netbsd:cpu_Debugger+0x4:        leave
db> bt
cpu_Debugger(0,c0800a5c,c0800a30,c032c865,c10eda60) at netbsd:cpu_Debugger+0x4
comintr(c1126e00,0,c0800010,30,10) at netbsd:comintr+0x6a1
Xintr_legacy3() at netbsd:Xintr_legacy3+0xa4
--- interrupt ---
cpu_switch(c0742780,0,1,0,1) at netbsd:cpu_switch+0x9f
ltsleep(ca3d6f88,11,c0665eb1,0,ca3d6fb0) at netbsd:ltsleep+0x317
biowait(ca3d6f88,0,250000,0,0) at netbsd:biowait+0x43
read_sector(c0800c30,0,0,0,0) at netbsd:read_sector+0x48
scan_mbr(c0800c30,c03d32dc,c0800c38,c05310f1,37eac80) at netbsd:scan_mbr+0x2e
readdisklabel(3,c03f5a60,c117ba00,c117b800,c10fc924) at netbsd:readdisklabel+0xc
8
wdgetdisklabel(c1177000,8,c117751c,51,c0745b20) at netbsd:wdgetdisklabel+0x90
wdopen(3,1,6000,0,e37ba000) at netbsd:wdopen+0x1ab
spec_open(c0800d30,48,0,c1177000,c055a000) at netbsd:spec_open+0x209
VOP_OPEN(e37ba000,1,ffffffff,0,c1170010) at netbsd:VOP_OPEN+0x34
rf_find_raid_components(c07425c0,805000,c0800f78,c034b701,0) at netbsd:rf_find_r
aid_components+0x102
rf_autoconfig(0,20,c0664aba,0,0) at netbsd:rf_autoconfig+0x23
config_finalize(0,0,0,0,0) at netbsd:config_finalize+0x1d
main(0,0,0,0,0) at netbsd:main+0x3cf
db> sync
syncing disks... done
wd0: flush cache command didn't complete
rebooting...
~
[EOT]

NetBSD 1.6ZD (TELSTAR) #9: Sun Oct 26 11:33:59 MST 2003
	root@telstar.bjan.net:/usr/obj/sys/arch/i386/compile/TELSTAR
total memory = 511 MB
avail memory = 470 MB
using 6144 buffers containing 26296 KB of memory
BIOS32 rev. 0 found at 0xf16f0
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon XP 2100+ (686-class), 1300.12 MHz, id 0x681
cpu0: features c3c3fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features c3c3fbff<PGE,MCA,CMOV,PAT,PSE36,MMXX,MMX>
cpu0: features c3c3fbff<FXSR,SSE,3DNOW2,3DNOW>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 200 MHz
cpu0: 8 page colors
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 3, 24 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 2
acpi0 at mainbus0
acpi0: using Intel ACPI CA subsystem version 20030228
acpi0: X/RSDT: OemId <ASUS  ,A7V8X   ,42302e31>, AslId <MSFT,31313031>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0C01 at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0A03 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0800 at acpi0 not configured
npx0 at acpi0 (PNP0C04)
npx0: io 0xf0-0xff irq 13
npx0: using exception 16
fdc0 at acpi0 (PNP0700)
fdc0: io 0x3f2-0x3f5,0x3f7 irq 6 drq 2
PNP0401 at acpi0 not configured
com0 at acpi0 (PNP0501-1)
com0: io 0x3f8-0x3ff irq 4
com0: ns16550a, working fifo
com1 at acpi0 (PNP0501-2)
com1: io 0x2f8-0x2ff irq 3
com1: ns16550a, working fifo
pckbc0 at acpi0 (PNP0303): kbd port
pckbc0: io 0x60,0x64 irq 1
PNP0C02 at acpi0 not configured
pckbd0 at pckbc0 (kbd slot)
pckbc0: irq=1
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
pckbc0: irq=1
pckbc0: unable to establish interrupt for aux slot
wsmouse0 at pms0 mux 0
configuring bus 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: VIA Technologies VT8377 Apollo KT400 CPU to PCI Bridge (rev. 0x00)
agp0 at pchb0: aperture at 0xf8000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: VIA Technologies VT8377 CPU-AGP Bridge (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 0 function 0: ATI Technologies Radeon 7500 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
fwohci0 at pci0 dev 7 function 0: VIA Technologies VT3606 OHCI IEEE 1394 Controller (rev. 0x80)
fwohci0: interrupting at ioapic0 pin 17 (irq 10)
fwohci0: OHCI 1.0, 00:e0:18:00:00:0c:be:46, 400Mb/s, 2048 max_rec, 4 ir_ctx, 8 it_ctx
Promise Technology Serial ATA/150 TX2plus Bus Master IDE Accelerator (RAID mass storage, revision 0x02) at pci0 dev 8 function 0 not configured
bge0 at pci0 dev 9 function 0: Broadcom BCM5702X Gigabit Ethernet
bge0: interrupting at ioapic0 pin 18 (irq 5)
bge0: ASIC BCM5703 A2, Ethernet address 00:e0:18:d2:a2:8a
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
puc0 at pci0 dev 10 function 0: SIIG Cyber 2S1P PCI 16C550 (10x family) (com, com, lpt)
com2 at puc0 port 0: interrupting at ioapic0 pin 16 (irq 11)
com2: ns16550a, working fifo
com3 at puc0 port 1: interrupting at ioapic0 pin 16 (irq 11)
com3: ns16550a, working fifo
lpt at puc0 port 2 not configured
machfb0 at pci0 dev 11 function 0: ATI Technologies Rage XL (rev. 0x27)
machfb0: 8 MB aperture at 0xe33b7000, 4 KB registers at 0xe33b6c00
machfb0: 16384 KB (unknown type) 29.498 MHz, maximum RAMDAC clock 230 MHz
machfb0: chip ID mismatch, 0xffff != 0x4752
ath0 at pci0 dev 13 function 0
ath0: interrupting at ioapic0 pin 16 (irq 11)
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: turbo rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 802.11 address: 00:0c:41:16:a7:95
uhci0 at pci0 dev 16 function 0: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci0: interrupting at ioapic0 pin 21 (irq 9)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 16 function 1: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci1: interrupting at ioapic0 pin 21 (irq 9)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 16 function 2: VIA Technologies VT83C572 USB Controller (rev. 0x80)
uhci2: interrupting at ioapic0 pin 21 (irq 9)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: VIA Technologies UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
VIA Technologies VT8237 EHCI USB Controller (USB serial bus, interface 0x20, revision 0x82) at pci0 dev 16 function 3 not configured
pcib0 at pci0 dev 17 function 0
pcib0: VIA Technologies VT8235 (Apollo KT400) PCI-ISA Bridge (rev. 0x00)
viaide0 at pci0 dev 17 function 1
viaide0: VIA Technologies VT8235 ATA133 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
auvia0 at pci0 dev 17 function 5: VIA VT8235 AC'97 Audio (rev 0x50)
auvia0: interrupting at ioapic0 pin 22 (irq 9)
auvia0: ac97: Avance Logic ALC650 codec; 20 bit DAC, 18 bit ADC, Realtek 3D
auvia0: ac97: ext id 5c7<AC97_22,LDAC,SDAC,CDAC,SPDIF,DRA,VRA>
audio0 at auvia0: full duplex, mmap, independent
isa0 at pcib0
atppc0 at isa0 port 0x378-0x37f irq 7 drq 3
atppc0: FIFO <depth,wthr,rthr>=<16,1,9>
atppc0: capabilities=3f<INTR,DMA,FIFO,PS2,ECP,EPP>
ppbus0 at atppc0
n2Tppbus0<1284>: error=3 status=0x7e event=24
ppbus0<1284>: error=2 status=0x7e event=2
Tppbus0<1284>: error=3 status=0x7e event=24
ppbus0: No IEEE1284 device found.
lpt0 at ppbus0: mode = 1<COMPATIBLE>
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
sysbeep0 at pcppi0
ioapic0: enabling
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
IPsec: Initialized Security Association Processing.
fw0 at fwohci0: 00:e0:18:00:00:0c:be:46:0a:02:ff:ff:f0:01:00:00
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <CD-RW IDE5224, , VER 001> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0 at atabus0 drive 0: <WDC WD300BB-00AUA1>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28629 MB, 58168 cyl, 16 head, 63 sec, 512 bytes/sect x 58633344 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
cd0(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
atapibus1 at atabus1: 2 targets
cd1 at atapibus1 drive 0: <HITACHI DVD-ROM GD-2500, , 0101> cdrom removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2
sd0 at atapibus1 drive 1: <IOMEGA  ZIP 100       ATAPI, , 23.D> disk removable
sd0: drive offline
sd0: 32-bit data port
cd1(viaide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
sd0(viaide0:1:1): using PIO mode 3
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
uhub0: port error, restarting port 2
uhub2: port error, restarting port 1
uhub2: port error, giving up port 1
umass0 at uhub2 port 2 configuration 1 interface 0
umass0: Genesys Logic USB TO IDE, rev 2.00/0.02, addr 2
umass0: using SCSI over Bulk-Only
uhub3 at uhub1 port 1scsibus0 at umass0: 2 targets, 1 lun per target
sd1 at scsibus0 target 0 lun 0: <IC25N040, ATCS04-0, 0811> disk fixed

uhub3: MCT Corporation. MCT4U, class 9/0, rev 1.00/1.01, addr 2
uhub3: 5 ports with 4 removable, self powered
sd1: fabricating a geometry
sd1: 38154 MB, 38154 cyl, 64 head, 32 sec, 512 bytes/sect x 78140160 sectors
uhub4 at uhub3 port 1
uhub4: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00, addr 3
uhub4: 4 ports with 4 removable, self powered
ulpt0 at uhub3 port 3 configuration 1 interface 0
ulpt0: EPSON USB Printer, rev 1.10/1.00, addr 4, iclass 7/1
ulpt0: using bi-directional mode
uscanner0 at uhub3 port 5
uscanner0: Color FlatbedScanner 13, rev 1.00/1.00, addr 5
uhidev0 at uhub1 port 2 configuration 1 interface 0
uhidev0: PCally Peripherals PCally USB & PS/2 Optical Internet Mouse, rev 1.10/0.01, addr 6, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
wd0: transfer error, downgrading to Ultra-DMA mode 2
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
cd0(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
wd0d: error reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0: (aborted command, interface CRC error)
wd0: soft error (corrected)
sd0(viaide0:1:1):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd1: fabricating a geometry
sd0(viaide0:1:1):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

boot device: wd0
root on wd0a dumps on wd0b
-- 
Bruce J.A. Nourish <bjan+public@bjan.net> http://bjan.net