i'm having trouble getting a pci cbb to work in the Tyan-MPX i bought
(for SMP experimentation).  it worked in the previous asus board.  i'm
not too keen on pc hardware and after trying various BIOS knobs, i must
ask for help/suggestions/clue.

the pci cbb is the one that lucent sells to service a wavelan card.  in
the tyan board it claims to have difficulty finding an interrupt (no idea
what cbb1 is).

cbb0 at pci2 dev 7 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
cbb0: NOT USED because of unconfigured interrupt
cbb1 at pci2 dev 7 function 1: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
cbb1: NOT USED because of unconfigured interrupt


in the asus board it looked like:

cbb0 at pci0 dev 12 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev. 0x01)
Texas Instruments PCI1225 PCI-CardBus Bridge (CardBus bridge, revision 0x01) at pci0 dev 12 function 1 not configured

cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 0 device 0
pcmcia0 at cardslot0

wi0 at pcmcia0 function 0: Lucent Technologies, WaveLAN/IEEE, Version 01.01
wi0: 802.11 address 00:02:2d:01:b1:a2 
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station (6.6.1)
wi0: supported rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
pccbb_intr_disestablish: pil 0xc0a5b9e0  

the BIOS supplies few options wrt the pci; bus master enable/disable,
latency timer, and "option rom scan".

consequently, it doesnt recognize the second fxp i have installed, but the
on-board ex0 is fine.

NetBSD 1.6J (nigmp) #2: Thu Oct 31 23:25:06 GMT 2002
    root@ni:/home/src/sys/arch/i386/compile/nigmp
total memory = 511 MB
avail memory = 471 MB
using 6144 buffers containing 26268 KB of memory
BIOS32 rev. 0 found at 0xfd6b0
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (TYAN     PAULANER    )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: AMD Athlon (686-class), 1200.11 MHz
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu0: features 383fbff<FXSR,SSE>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 266 MHz
cpu0: 8 page colors
cpu1 at mainbus0: apid 0 (application processor)
cpu1: starting
cpu1: AMD Athlon (686-class), 1200.05 MHz
cpu1: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX>
cpu1: features 383fbff<FXSR,SSE>
cpu1: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu1: L2 cache 256 KB 64b/line 16-way
cpu1: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu1: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type PCI   
mpbios: bus 3 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Advanced Micro Devices AMD762 NorthBridge (rev. 0x11)
agp0 at pchb0pci_mem_find: void region
: can't map aperture
ppb0 at pci0 dev 1 function 0: Advanced Micro Devices AMD762 AGP Bridge (rev. 0x
00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: ATI Technologies 3D Rage Pro (AGP) (rev. 0x5c)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 7 function 0
pcib0: Advanced Micro Devices AMD768 PCI to ISA/LPC Bridge (rev. 0x05)
pciide0 at pci0 dev 7 function 1: Advanced Micro Devices AMD768 IDE Controller (
rev. 0x04)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <WDC WD153AA-53BAA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 14679 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 30064608 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd1 at pciide0 channel 0 drive 1: <WDC WD1200JB-75CRA0>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 111 GB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 234375000 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA data 
transfers)
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data
 transfers)
pciide0: secondary channel configured to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <CD-540E, , 1.0A> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data 
transfers)
Advanced Micro Devices AMD768 Power Management Controller (miscellaneous bridge,
 revision 0x03) at pci0 dev 7 function 3 not configured
ppb1 at pci0 dev 16 function 0: Advanced Micro Devices AMD768 PCI to PCI Bridge 
(rev. 0x05)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
ohci0 at pci2 dev 0 function 0: Advanced Micro Devices AMD768 USB Controller (re
v. 0x07)
ohci0: interrupting at apic 2 int 19 (irq 10)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Advanced Micro OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
fxp0 at pci2 dev 5 function 0: Intel i82557 Ethernet, rev 2
fxp0: interrupting at apic 2 int 17 (irq 5)
fxp0: Ethernet address 00:a0:c9:6e:d4:d5
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
siop0 at pci2 dev 6 function 0: Symbios Logic 53c810 (fast scsi)
siop0: interrupting at apic 2 int 18 (irq 11)
scsibus0 at siop0: 8 targets, 8 luns per target
cbb0 at pci2 dev 7 function 0: Texas Instruments PCI1225 PCI-CardBus Bridge (rev
. 0x01)
cbb0: NOT USED because of unconfigured interrupt
cbb1 at pci2 dev 7 function 1: Texas Instruments PCI1225 PCI-CardBus Bridge (rev
. 0x01)
cbb1: NOT USED because of unconfigured interrupt
ex0 at pci2 dev 8 function 0: 3Com 3c905C-TX 10/100 Ethernet with mngmt (rev. 0x
78)
ex0: interrupting at apic 2 int 19 (irq 10)
ex0: MAC address 00:e0:81:23:26:c0
exphy0 at ex0 phy 24: 3Com internal media interface
exphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
wskbd0: connecting to wsdisplay0
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask 0 netmask 0 ttymask 0
ioapic0: enabling
ioapic0: WARNING: sharing interrupt between different IPLs (currently broken)
ioapic0: pin 19, ipls 70..80
scsibus0: waiting 2 seconds for devices to settle...
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
cpu1: CPU 0 running