Hello Mickael Maraval san, Hello All,


I am isao nagamori in Tokyo. How do you do ?
Thank you very much for replying to our question.

 
> I 've had the same problem.
> Unfortunately,you may need a PCI Ethernet card if you want to boot, cause
> the onboard ethernet controller is not supported.
> Otherwise, you need to boot over LAN - use archive to see how it works.
> 
> Hope you 'll succeed in.

I bought a PCI-Ethernet card and installed it with our O2.

Then I have a question. 
How can I select the PCI Ethernet as boot device?

I tried as follows, but I could not boot it.

> boot -f bootp():/netbsd.ip32
ec0: no carrier: check the Ethernet cable
Unable to excute bootp():/netbsd.ip32: IO error
Unable to load bootp():/netbsd.ip32: no such device
>


Thank you very much.

Regards,




> ----- Original Message -----
> From: "Yutaka Narumai" <ynarumai@marubun.co.jp>
> To: "Mickael Maraval" <mmaraval@spring.fr>
> Cc: <port-sgimips@NetBSD.ORG>; "Isao Nagamori" <r17413@email.sps.mot.com>
> Sent: Tuesday, February 26, 2002 2:06 PM
> Subject: Re: SGI O2 net boot problem
> 
> > Bonjour Monsieur,
> > Merci beaucoup pour votre reponse.
> > Vous etes bien aimable.
> >
> > I tried IP32 kernel.
> > The result is as follows;
> > It seems better than before but it stops.
> >
> >             Sincerely yours,
> >
> >             Yutaka Narumai
> >
> > ========================================================================
> > > boot -f boot():/netbsd.ip32
> > Setting $netaddr to 223.1.1.2 (from server 223.1.1.1)
> > Obtaining /netbsd.ip32 from server 223.1.1.1
> > 1245528+36896+152192 entry: 0x80002000
> > memory 0x163000 0x1060000
> > memory 0x140100 0x8000000
> > Copyright (c) 1996, 1997, 1998, 1999, 2000
> >     The NetBSD Foundation, Inc, All rights reserved.
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> >     The Regents of the University of California, All rights reserved.
> >
> > NetBSD 1.5A (INDY) #142: Tue Jun 27 17:40:37 CEST 2000
> >     soren@meow:/usr/home/soren/netbsd/src/sys/arch/sgimips/compile/INDY
> > 128 MB memory,81856 KB free, 3716 KB for ARCS, 39240 KB in 9810 buffers
> > mainbus0 (root): SGI-IP32 [SGI, I]
> > cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with built-in FPU Rev.
> > 1.0
> > cpu0: L1 cache: 32KB/32B instruction, 32KB/32B data, two way set
> > associative
> > cpu0: L2 cache: 512KB/32B mixed, snooping
> > crime0 at mainbus0 addr 0x14000000: rev 1.1
> > mace0 at mainbus0 addr 0x1f000000
> > com0 at mace0 offset 0x390000 intr 4: ns16550a, working fifo
> > com1 at mace0 offset 0x398000 intr 4: ns16550a, working fifo
> > pckbc0 at mace0 offset 0x320000 intr 5: stub
> >  lpt0 at mace0 offset 0x380000 intr 4
> > mec0 at mace0 offset 0x280000 intr 3: MAC-110 Ethernet, rev 1
> > mec0: station address 08:00:69:0a:ba:21
> > mec0: sorry, this is not a real driver
> > nsphy0 at mec0 phy 9: DP83840 10/100 media interface, rev. 0
> > nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > macepc0 at mace0 offset 0x80000 intr 7: rev 1
> > panic: pcierr: 80180006 4004
> > Stopped in swapper at 0x800f74b4:       jr    ra
> >                     bdslot: 0x800f74b8:  nop
> > ======================================================================
> > > Try with an IP32 kernel.
> > > ----- Original Message -----
> > > From: "Yutaka Narumai" <ynarumai@marubun.co.jp>
> > > To: <port-sgimips@NetBSD.ORG>
> > > Cc: "Isao Nagamori" <r17413@email.sps.mot.com>
> > > Sent: Tuesday, February 26, 2002 9:40 AM
> > > Subject: SGI O2 net boot problem
> > >
> > >
> > > > Dear friends,
> > > >
> > > > I try to make a net-boot o2 system using the sgimips-20011002
> > > > file.
> > > > But the following error message comes out on the screen;
> > > > I use pentium base note book(NetBSD-i386 installed) and
> > > > 10Base-T cross cable.
> > > > Any advise will be highly appreciated.
> > > >
> > > >                sincerely,
> > > >
> > > >
> ============================================================================
> > > > >boot -f bootp():/netbsd.ip22
> > > > Setting $netaddr to 223.1.1.2 (from server 223.1.1.1)
> > > > Obtaining /netbsd.ip22 from server 223.1.1.1
> > > > 1262208
> > > > Cannot load bootp():/netbsd.ip22
> > > > Range check failure: text start 0x88002000, size 0x134280
> > > > Text section would overwritten an already loaded program. Unableto
> > > > execute
> > > > boot():/netbsd.ip22: not enough space
> > > > Unable to load bootp():/netbsd.ip22: not enough space
> > > > 
> ============================================================================