This is more than I did expect:-)

best regards
Matthias

NetBSD 1.5ZA (GENERIC.MPDEBUG) #1: Mon Jan  7 17:17:36 MET 2002
    drochner@zelz26:/home/drochner/netbsd/sys/arch/i386/compile/GENERIC.MPDEBUG
total memory = 2047 MB
avail memory = 1873 MB
using 6144 buffers containing 102 MB of memory
BIOS32 rev. 0 found at 0xfd6a0
mainbus0 (root)
mainbus0: scanning 0x9f400 to 0x9f7f0 for MP signature
mainbus0: scanning 0x9f000 to 0x9f3f0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xf74e0
mainbus0: MP config table at 0x9f870, 260 bytes long
mainbus0: Intel MP Specification (Version 1.4) (TYAN     GUINNESS    )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: AMD K7 (Athlon) (686-class), 1194.75 MHz
cpu0: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX,FXSR,SSE>
cpu0: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu0: L2 cache 256 KB 64b/line 16-way
cpu0: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 265 MHz
cpu0: 8 page colors
cpu0: kstack at 0xe6082000 for 8192 bytes
cpu0: idle pcb at 0xe6082000, idle sp at 0xe6083f98
cpu1 at mainbus0: apid 0 (application processor)
cpu1: starting
cpu1: AMD K7 (Athlon) (686-class), 1194.68 MHz
cpu1: features 383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 383fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX,FXSR,SSE>
cpu1: I-cache 64 KB 64b/line 2-way, D-cache 64 KB 64b/line 2-way
cpu1: L2 cache 256 KB 64b/line 16-way
cpu1: ITLB 16 4 KB entries fully associative, 8 4 MB entries fully associative
cpu1: DTLB 32 4 KB entries fully associative, 8 4 MB entries 4-way
cpu1: kstack at 0xe6084000 for 8192 bytes
cpu1: idle pcb at 0xe6084000, idle sp at 0xe6085f98
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, virtual wire mode, version 11, 24 pins
ioapic0: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int1 attached to isa0 irq 1 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int2 attached to isa0 irq 0 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int3 attached to isa0 irq 3 (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: int4 attached to isa0 irq 4 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int5 attached to isa0 irq 5 (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: int6 attached to isa0 irq 6 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int7 attached to isa0 irq 7 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int8 attached to isa0 irq 8 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int9 attached to isa0 irq 9 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int10 attached to isa0 irq 10 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int11 attached to isa0 irq 11 (type 0<type=0> flags f<pol=3=Act 
Lo,trig=3=Level>)
ioapic0: int12 attached to isa0 irq 12 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int13 attached to isa0 irq 13 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int14 attached to isa0 irq 14 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
ioapic0: int15 attached to isa0 irq 15 (type 0<type=0> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
local apic: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
local apic: int1 attached to NMI (type 1<type=1=NMI> flags 5<pol=1=Act 
Hi,trig=1=Edge>)
mainbus0: MP WARNING: 344 bytes of extended entries not examined
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Advanced Micro Devices AMD762 NorthBridge (rev. 0x11)
agp at pchb0 not configured
ppb0 at pci0 dev 1 function 0: Advanced Micro Devices AMD762 AGP Bridge (rev. 
0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: Matrox MGA G400 AGP (rev. 0x85)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0
pcib0: Advanced Micro Devices AMD766 SouthBridge (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Advanced Micro Devices AMD766 IDE Controller 
(rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
atapibus0 at pciide0 channel 0: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA CD-ROM XM-6402B, , 1015> type 5 cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: primary channel interrupting at irq 14
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA 
data transfers)
pciide0: secondary channel configured to compatibility mode
pciide0: disabling secondary channel (no drives)
Advanced Micro Devices AMD766 Power Management Controller (miscellaneous 
bridge, revision 0x01) at pci0 dev 7 function 3 not configured
ohci0 at pci0 dev 7 function 4: Advanced Micro Devices AMD766 USB Host 
Controller (rev. 0x07)
pci_intr_map: bus 0 dev 7 func 4 pin 4; line 11
pci_intr_map: no MP mapping found
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Advanced Micro OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
Elsa QuickStep 1000 ISDN card (miscellaneous network, revision 0x01) at pci0 
dev 8 function 0 not configured
FZ Juelich / ZEL Gigabit link / STR1100 (miscellaneous communications, 
revision 0x01) at pci0 dev 10 function 0 not configured
eap0 at pci0 dev 11 function 0: Ensoniq CT5880 CT5880C (rev. 0x02)
pci_intr_map: bus 0 dev 11 func 0 pin 1; line 11
pci_intr_map: no MP mapping found
eap0: interrupting at irq 11
eap0: SigmaTel STAC9721/23 codec; 18 bit DAC, 18 bit ADC, Rockwell 3D
audio0 at eap0: full duplex, mmap, independent
midi0 at eap0: AudioPCI MIDI UART
ahc1 at pci0 dev 13 function 0
ahc1: OptionMode = 3
pci_intr_map: bus 0 dev 13 func 0 pin 1; line 5
pci_intr_map: no MP mapping found
ahc1: interrupting at irq 5
ahc1: aic7899 Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus0 at ahc1: 16 targets, 8 luns per target
ahc2 at pci0 dev 13 function 1
ahc2: OptionMode = 3
pci_intr_map: bus 0 dev 13 func 1 pin 2; line 11
pci_intr_map: no MP mapping found
ahc2: interrupting at irq 11
ahc2: aic7899 Wide Channel B, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc2: 16 targets, 8 luns per target
ex0 at pci0 dev 15 function 0: 3Com 3c980C-TXM 10/100 Ethernet (rev. 0x78)
pci_intr_map: bus 0 dev 15 func 0 pin 1; line 3
pci_intr_map: no MP mapping found
ex0: interrupting at irq 3
ex0: MAC address 00:e0:81:04:c7:28
ex0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, default 10baseT
ex1 at pci0 dev 16 function 0: 3Com 3c980C-TXM 10/100 Ethernet (rev. 0x78)
pci_intr_map: bus 0 dev 16 func 0 pin 1; line 11
pci_intr_map: no MP mapping found
ex1: interrupting at irq 11
ex1: MAC address 00:e0:81:04:c7:29
ex1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, default 10baseT
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsiprobe: intellimode -> 6
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lptprobe: mask ff data 55 failed
lptprobe: mask ff data 55 failed
lptprobe: mask ff data 55 failed
seaprobe: board type unknown at address 0xc8000
pcppi0 at isa0 port 0x61
midi1 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: no ISA Plug 'n Play devices found
biomask 0 netmask 0 ttymask 0
cpu0: prelint0 700<vector=0,delmode=7,dest=0> 0<target=0>
cpu0: prelint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: timer0 300d0<vector=d0,delmode=0,masked,dest=0> 0<target=0>
cpu0: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu0: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu0: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: enabling
ioapic0: int0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
ioapic0: int1 1a0<vector=a0,delmode=1,dest=0> 1000000<target=1>
ioapic0: int2 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int3 a181<vector=81,delmode=1,actlo,level,dest=0> 1000000<target=1>
ioapic0: int4 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int5 a170<vector=70,delmode=1,actlo,level,dest=0> 1000000<target=1>
ioapic0: int6 171<vector=71,delmode=1,dest=0> 1000000<target=1>
ioapic0: int7 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int8 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int9 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int10 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: WARNING: sharing interrupt between different IPLs (currently broken)
ioapic0: pin 11, ipls 70..c0
ioapic0: int11 a172<vector=72,delmode=1,actlo,level,dest=0> 1000000<target=1>
ioapic0: int12 1a1<vector=a1,delmode=1,dest=0> 1000000<target=1>
ioapic0: int13 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int14 173<vector=73,delmode=1,dest=0> 1000000<target=1>
ioapic0: int15 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int16 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int17 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int18 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int19 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int20 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int21 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int22 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int23 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST318437LW, 0105> SCSI3 0/direct 
fixed
sd0: 17547 MB, 29851 cyl, 2 head, 601 sec, 512 bytes/sect x 35937500 sectors
sd0: sync (50.0ns offset 31), 16-bit (40.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <SEAGATE, ST318437LW, 0105> SCSI3 0/direct 
fixed
sd1: 17547 MB, 29851 cyl, 2 head, 601 sec, 512 bytes/sect x 35937500 sectors
sd1: sync (50.0ns offset 31), 16-bit (40.000MB/s) transfers, tagged queueing
sd2 at scsibus0 target 3 lun 0: <IBM, DCAS-34330W, S65A> SCSI2 0/direct fixed
sd2: 4134 MB, 8205 cyl, 6 head, 171 sec, 512 bytes/sect x 8467200 sectors
sd2: sync (50.0ns offset 15), 16-bit (40.000MB/s) transfers, tagged queueing
scsibus1: waiting 2 seconds for devices to settle...
sd3 at scsibus1 target 2 lun 0: <IBM, DDRS-39130, S97B> SCSI2 0/direct fixed
sd3: 8715 MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sect x 17850000 sectors
sd3: sync (50.0ns offset 15), 8-bit (20.000MB/s) transfers, tagged queueing
st0 at scsibus1 target 5 lun 0: <HP, Ultrium 1-SCSI, E0AD> SCSI3 1/sequential 
removable
st0: density code 64, variable blocks, write-enabled
st0: sync (100.0ns offset 15), 16-bit (20.000MB/s) transfers
sd0: no disk label
findroot: can't open dev sd0a (6)
sd2: no disk label
findroot: can't open dev sd2a (6)
sd3: no disk label
findroot: can't open dev sd3a (6)
boot device: sd1
root device (default sd1a): 
dump device (default sd1b): 
file system (default generic): 
root on sd1a dumps on sd1b
mountroot: trying coda...
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying ntfs...
mountroot: trying nfs...
mountroot: trying lfs...
mountroot: trying ext2fs...
mountroot: trying ffs...
root file system type: ffs
cpu1: prelint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: prelint1 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: timer0 200d0<vector=d0,delmode=0,dest=0> 0<target=0>
cpu1: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu1: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu1: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: CPU 0 running
init: copying out path `/sbin/init' 11
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)