GENERIC.MP from an abit bp6.
the bios finds ep0 at 5 but..
the smp kernel placed ep0 at 3 together w/ com1.
(GENERIC places ep0 at 5)

i'd love to use them both (as they were)
thanx for remarks..
~n


NetBSD 1.5Y (GENERIC.MP) #0: Wed Nov 28 14:09:32 CET 2001
    root@CP136829-A:/usr/syssrc/sys/arch/i386/compile/GENERIC.MP
total memory = 127 MB
avail memory = 111 MB
using 1659 buffers containing 6636 KB of memory
BIOS32 rev. 0 found at 0xfb590
mainbus0 (root)
mainbus0: scanning 0x9fc00 to 0x9fff0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xf5ae0
mainbus0: MP config table at 0xf1400, 260 bytes long
mainbus0: Intel MP Specification (Version 1.1) (OEM00000 PROD00000000)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Celeron (Mendocino) (686-class), 400.93 MHz
cpu0: features 183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features 183fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX,FXSR>
cpu0: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu0: L2 cache 128 KB 32b/line 4-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: calibrating local timer
cpu0: apic clock running at 66 MHz
cpu0: 8 page colors
cpu0: kstack at 0xcab26000 for 8192 bytes
cpu0: idle pcb at 0xcab26000, idle sp at 0xcab27f98
cpu1 at mainbus0: apid 1 (application processor)
cpu1: starting
cpu1: Intel Celeron (Mendocino) (686-class), 400.91 MHz
cpu1: features 183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features 183fbff<PGE,MCA,CMOV,FGPAT,PSE36,MMX,FXSR>
cpu1: I-cache 16 KB 32b/line 4-way, D-cache 16 KB 32b/line 4-way
cpu1: L2 cache 128 KB 32b/line 4-way
cpu1: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu1: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu1: kstack at 0xcab28000 for 8192 bytes
cpu1: idle pcb at 0xcab28000, idle sp at 0xcab29f98
mpbios: bus 0 is type PCI   
mpbios: bus 1 is type PCI   
mpbios: bus 2 is type ISA   
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, virtual wire mode, version 11, 24 pins
ioapic0: int0 attached to ExtINT (type 3<type=3=ExtINT> flags 0<pol=0,trig=0>)
ioapic0: int1 attached to isa0 irq 1 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int2 attached to isa0 irq 0 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int3 attached to isa0 irq 3 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int4 attached to isa0 irq 4 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int5 attached to isa0 irq 5 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int6 attached to isa0 irq 6 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int7 attached to isa0 irq 7 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int8 attached to isa0 irq 8 (type 0<type=0> flags 5<pol=1=Act
Hi,trig=1=Edge>)
ioapic0: int9 attached to isa0 irq 9 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int13 attached to isa0 irq 13 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int14 attached to isa0 irq 14 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int15 attached to isa0 irq 15 (type 0<type=0> flags 0<pol=0,trig=0>)
ioapic0: int17 attached to isa0 irq 10 (type 0<type=0> flags f<pol=3=Act
Lo,trig=3=Level>)
ioapic0: int18 attached to isa0 irq 11 (type 0<type=0> flags f<pol=3=Act
Lo,trig=3=Level>)
ioapic0: int19 attached to isa0 irq 12 (type 0<type=0> flags f<pol=3=Act
Lo,trig=3=Level>)
local apic: int0 attached to ExtINT (type 3<type=3=ExtINT> flags
0<pol=0,trig=0>)
local apic: int1 attached to NMI (type 1<type=1=NMI> flags 0<pol=0,trig=0>)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82443BX Host Bridge/Controller (rev. 0x03)
agp at pchb0 not configured
ppb0 at pci0 dev 1 function 0: Intel 82443BX AGP Interface (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
pcib0 at pci0 dev 7 function 0
pcib0: Intel 82371AB PCI-to-ISA Bridge (PIIX4) (rev. 0x02)
pciide0 at pci0 dev 7 function 1: Intel 82371AB IDE controller (PIIX4) (rev.
0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
atapibus0 at pciide0 channel 0: 2 targets
cd0 at atapibus0 drive 1: <CREATIVE CD-RW RW4424E, , 1.12> type 5 cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
wd0 at pciide0 channel 0 drive 0: <ST38421A>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 8056 MB, 16368 cyl, 16 head, 63 sec, 512 bytes/sect x 16498944 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data
transfers)
cd0(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
wd1 at pciide0 channel 1 drive 0: <ST340823A>
wd1: drive supports 16-sector PIO transfers, LBA addressing
wd1: 38166 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 78165360 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
pciide0: secondary channel interrupting at irq 15
wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data
transfers)
uhci0 at pci0 dev 7 function 2: Intel 82371AB USB Host Controller (PIIX4) (rev.
0x01)
pci_intr_map: no mapping for pin D (line=ff)
uhci0: couldn't map interrupt
Intel 82371AB Power Management Controller (PIIX4) (miscellaneous bridge,
revision 0x02) at pci0 dev 7 function 3 not configured
r
tk0 at pci0 dev 9 function 0: RealTek 8129 10/100BaseTX
pci_intr_map: no MP mapping found
rtk0: interrupting at irq 12
rtk0: Ethernet address 00:c0:26:60:2d:7c
ukphy0 at rtk0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ex0 at pci0 dev 13 function 0: 3Com 3c905-TX 10/100 Ethernet (rev. 0x0)
pci_intr_map: no MP mapping found
ex0: interrupting at irq 10
ex0: MAC address 00:60:08:50:14:f4
nsphy0 at ex0 phy 24: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vga1 at pci0 dev 15 function 0: S3 Trio64V2/DX (rev. 0x06)
wsdisplay0 at vga1 kbdmux -1: console (80x25, vt100 emulation)
pciide1 at pci0 dev 19 function 0: Triones/Highpoint HPT366 IDE Controller
pciide1: bus-master DMA support present
pciide1: primary channel wired to native-PCI mode
pci_intr_map: no MP mapping found
pciide1: using irq 11 for native-PCI interrupt
pciide2 at pci0 dev 19 function 1: Triones/Highpoint HPT366 IDE Controller
pciide2: bus-master DMA support present
pciide2: primary channel wired to native-PCI mode
pci_intr_map: no MP mapping found
pciide2: using irq 11 for native-PCI interrupt
isa0 at pcib0
3COM 3C509B Ethernet card in PnP mode
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsprobe: reset error 5
pmsiprobe: reset error 5
lpt0 at isa0 port 0x378-0x37b irq 7
lptprobe: mask ff data 55 failed
lptprobe: mask ff data 55 failed
seaprobe: board type unknown at address 0xc8000
ec0 at isa0 port 0x250-0x25f iomem 0xd8000-0xd9fff irq 9
ec0: 3Com 3c503 Ethernet (8-bit)
ec0: Ethernet address 02:60:8c:a3:71:bd
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
isapnp0: read port 0x203
ep0 at isapnp0 port 0x210/16 irq 3
ep0: 3Com 3C509B EtherLink III 
ep0: address 00:a0:24:97:c6:1f, 8KB byte-wide FIFO, 5:3 Rx:Tx split
ep0: 10baseT, 10base5, 10base2 (default 10baseT)
biomask 0 netmask 0 ttymask 0
cpu0: prelint0 700<vector=0,delmode=7,dest=0> 0<target=0>
cpu0: prelint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: timer0 300d0<vector=d0,delmode=0,masked,dest=0> 0<target=0>
cpu0: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu0: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu0: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu0: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: enabling
ioapic0: int0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
ioapic0: int1 1a0<vector=a0,delmode=1,dest=0> 0<target=0>
ioapic0: int2 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: WARNING: sharing interrupt between different IPLs (currently broken)
ioapic0: pin 3, ipls 80..e0
ioapic0: int3 1e1<vector=e1,delmode=1,dest=0> 0<target=0>
ioapic0: int4 1e2<vector=e2,delmode=1,dest=0> 0<target=0>
ioapic0: int5 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int6 170<vector=70,delmode=1,dest=0> 0<target=0>
ioapic0: int7 1a1<vector=a1,delmode=1,dest=0> 0<target=0>
ioapic0: int8 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int9 181<vector=81,delmode=1,dest=0> 0<target=0>
ioapic0: int10 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int11 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int12 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int13 10100<vector=0,delmode=1,masked,dest=0> 0<target=0>
ioapic0: int14 171<vector=71,delmode=1,dest=0> 0<target=0>
ioapic0: int15 172<vector=72,delmode=1,dest=0> 0<target=0>
ioapic0: int16 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int17 a182<vector=82,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int18 a173<vector=73,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int19 a183<vector=83,delmode=1,actlo,level,dest=0> 0<target=0>
ioapic0: int20 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int21 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int22 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
ioapic0: int23 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying coda...
mountroot: trying msdos...
mountroot: trying cd9660...
mountroot: trying ntfs...
mountroot: trying nfs...
mountroot: trying lfs...
mountroot: trying ext2fs...
mountroot: trying ffs...
root file system type: ffs
cpu1: prelint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: prelint1 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: timer0 200d0<vector=d0,delmode=0,dest=0> 0<target=0>
cpu1: pcint0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: lint0 10700<vector=0,delmode=7,masked,dest=0> 0<target=0>
cpu1: lint1 400<vector=0,delmode=4,dest=0> 0<target=0>
cpu1: err0 10000<vector=0,delmode=0,masked,dest=0> 0<target=0>
cpu1: CPU 1 running
init: copying out path `/sbin/init' 11
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0


-- 
----------------------------------
  ## UNIX is an abbreviation ##
----------------------------------