Re: Nvidia MCP67 SATA controller

To: tech-kern%NetBSD.org@localhost
Subject: Re: Nvidia MCP67 SATA controller
From: George Georgalis <george%galis.org@localhost>
Date: Fri, 27 Jun 2008 23:07:01 -0400
On Wed 18 Jun 2008 at 07:30:41 PM +0200, Dieter Baron wrote:
>
>  Attached is a diff that forces it into AHCI mode and thus attaches
>ahcisata.  The method to switch to AHCI mode was taken from the
>FreeBSD source tree.
>
>  This works quite well most of the time, but sometimes the chip seems
>to get in a strange state after the switch.  It then returns bogus
>data when identifying the drive:
>       wd0 at atabus1 drive 0: <ST506>
>(or similar, written from memory) instead of 
>       wd0 at atabus1 drive 0: <Hitachi HDT725032VLA360>
>and hangs when trying to read from the disk (still during boot).
>
>  If the boot is successful, the controller is stable.  I've used it
>to reconstruct a 320gb raid1.

I have very similar symptoms on an amd64 nvidia/via system.

about 10% (or less?) of the time it locks up before
"boot device: wd0" (normally the usb keyboard is not
attached), if it doesn't lockup than the cflash reader
works fine. (almost always there is no cflash installed
on this system).

BTW - I also dono why wd0 is UDMA 5 while wd1 is UDMA 6,
they are the same drive.... and re0 is flaking.

This is netbsd-4-0-RELEASE can try any recommended
patches....  The dmesg is below...

// George


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0 (GENERIC) #0: Sun Dec 16 00:20:10 PST 2007
        
builds@wb34:/home/builds/ab/netbsd-4-0-RELEASE/i386/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 1023 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 995 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfbd10
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon 64 (686-class), 2210.87 MHz, id 0xf4a
cpu0: features e7dbfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features e7dbfbff<PGE,MCA,CMOV,PAT,PSE36,MPC,NOX,MMXX,MMX>
cpu0: features e7dbfbff<FXSR,SSE,SSE2,LONG,3DNOW2,3DNOW>
cpu0: "AMD Athlon(tm) 64 Processor 3400+"
cpu0: I-cache 64 KB 64B/line 2-way, D-cache 64 KB 64B/line 2-way
cpu0: L2 cache 1 MB 64B/line 16-way
cpu0: ITLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: DTLB 32 4 KB entries fully associative, 8 4 MB entries fully associative
cpu0: AMD Power Management features: f<TTP,VID,FID,TS>
cpu0: AMD Cool`n'Quiet Technology 2200 MHz
cpu0: available frequencies (Mhz): 1000 1800 2000 2200
cpu0: calibrating local timer
cpu0: apic clock running at 200 MHz
cpu0: 16 page colors
ioapic0 at mainbus0 apid 2 (I/O APIC)
ioapic0: pa 0xfec00000, version 11, 24 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <XPC   ,AWRDACPI,42302e31>, AslId <AWRD,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
PNP0C01 [System Board] at acpi0 not configured
PNP0A03 [PCI/PCI-X Host Bridge] at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
PNP0700 [PC standard floppy disk controller] at acpi0 not configured
PNP0501 [16550A-compatible COM port] at acpi0 not configured
PNP0400 [Standard LPT printer port] at acpi0 not configured
pckbc1 at acpi0 (PNP0F13): aux port
pckbc1: irq 12
pckbc2 at acpi0 (PNP0303): kbd port
pckbc2: io 0x60,0x64 irq 1
PNP0C0B [ACPI Fan] at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: active cooling level 0: 100.0C
acpitz0: critical 110.0C passive 40.0C
pcppi1: attached to attimer1
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: NVIDIA nForce3 250 Host-PCI bridge (rev. 0xa1)
agp at pchb0 not configured
pcib0 at pci0 dev 1 function 0
pcib0: NVIDIA nForce3 250 PCI-ISA bridge (rev. 0xa2)
NVIDIA nForce3 250 SMBus Controller (SMBus serial bus, revision 0xa1) at pci0 
dev 1 function 1 not configured
ohci0 at pci0 dev 2 function 0: NVIDIA nForce3 250 USB Host Controller (rev. 
0xa1)
APCF: Picked IRQ 20 with weight 0
ohci0: interrupting at ioapic0 pin 20 (irq 5)
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1 at pci0 dev 2 function 1: NVIDIA nForce3 250 USB Host Controller (rev. 
0xa1)
APCG: Picked IRQ 21 with weight 0
ohci1: interrupting at ioapic0 pin 21 (irq 5)
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
ehci0 at pci0 dev 2 function 2: NVIDIA nForce3 250 USB2 Host Controller (rev. 
0xa2)
APCL: Picked IRQ 22 with weight 0
ehci0: interrupting at ioapic0 pin 22 (irq 5)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 4 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NVIDIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
nfe0 at pci0 dev 5 function 0: NVIDIA nForce3 ethernet #4 (rev. 0xa2)
APCH: Picked IRQ 20 with weight 1
nfe0: interrupting at ioapic0 pin 20 (irq 10)
nfe0: Ethernet address 00:30:1b:b7:15:44
rlphy0 at nfe0 phy 1: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
auich0 at pci0 dev 6 function 0: nForce3 250 MCP-T AC-97 Audio
APCJ: Picked IRQ 21 with weight 1
auich0: interrupting at ioapic0 pin 21 (irq 11)
auich0: ac97: Avance Logic ALC655 codec; no 3D stereo
auich0: ac97: ext id 9c4<AC97_23,LDAC,SDAC,CDAC,SPDIF>
viaide0 at pci0 dev 8 function 0
viaide0: NVIDIA nForce3 250 IDE Controller (rev. 0xa2)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 10 function 0
viaide1: NVIDIA nForce3 250 Serial ATA Controller (rev. 0xa2)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
APSJ: Picked IRQ 22 with weight 1
viaide1: using ioapic0 pin 22 (irq 11) for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
ppb0 at pci0 dev 11 function 0: NVIDIA nForce3 250 AGP (rev. 0xa2)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: NVIDIA GeForce2 MX (rev. 0xa1)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
ppb1 at pci0 dev 14 function 0: NVIDIA nForce3 250 PCI-PCI bridge (rev. 0xa2)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
re0 at pci2 dev 6 function 0: RealTek 8169/8110 Gigabit Ethernet (rev. 0x10)
re0: interrupting at ioapic0 pin 18 (irq 5)
re0: Ethernet address 00:40:f4:cb:ea:7a
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S 1000BASE-T media interface, rev. 0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
fwohci0 at pci2 dev 7 function 0: VIA Technologies VT6306 IEEE 1394 Host 
Controller (rev. 0x46)
fwohci0: interrupting at ioapic0 pin 19 (irq 10)
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:30:1b:b7:00:00:15:a8
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
pchb1 at pci0 dev 24 function 0
pchb1: Advanced Micro Devices AMD64 HyperTransport configuration (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: Advanced Micro Devices AMD64 Address Map configuration (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: Advanced Micro Devices AMD64 DRAM configuration (rev. 0x00)
pchb4 at pci0 dev 24 function 3
pchb4: Advanced Micro Devices AMD64 Miscellaneous configuration (rev. 0x00)
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
audio0 at auich0: full duplex, independent
Kernelized RAIDframe activated
viaide1 port 0: device present, speed: 1.5Gb/s
viaide1 port 1: device present, speed: 1.5Gb/s
uhub3 at uhub0 port 2
uhub3: Dell Dell USB Keyboard Hub, class 9/0, rev 1.10/1.00, addr 2
uhub3: 3 ports with 2 removable, bus powered
umass0 at uhub2 port 8 configuration 1 interface 0
umass0: USB2.0 CardReader, rev 2.00/91.38, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 2 luns per target
sd0 at scsibus0 target 0 lun 0: <USB2.0, CF  CardReader, > disk removable
sd0: drive offline
sd1 at scsibus0 target 0 lun 1: <USB2.0, CBO CardReader, > disk removable
sd1: drive offline
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA DVD-ROM SD-R5002, Y2PQ102690, 1031> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
wd0 at atabus2 drive 0: <ST3200822AS>
wd0: quirks 2<FORCE_LBA48>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 186 GB, 387621 cyl, 16 head, 63 sec, 512 bytes/sect x 390721968 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd1 at atabus3 drive 0: <ST3200822AS>
wd1: quirks 2<FORCE_LBA48>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 186 GB, 387621 cyl, 16 head, 63 sec, 512 bytes/sect x 390721968 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(viaide1:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd1(umass0:0:0:1):  Check Condition on CDB: 0x00 20 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd1(umass0:0:0:1):  Check Condition on CDB: 0x00 20 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

uhidev0 at uhub3 port 1 configuration 1 interface 0sd1(umass0:0:0:1):  Check 
Condition on CDB: 0x00 20 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present


uhidev0: Dell Dell USB Keyboard Hub, rev 1.10/1.00, addr 3, iclass 3/1
ukbd0 at uhidev0
sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

sd1(umass0:0:0:1):  Check Condition on CDB: 0x00 20 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Medium Not Present

boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub3 port 1 configuration 1 interface 1
uhidev1: Dell Dell USB Keyboard Hub, rev 1.10/1.00, addr 3, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 3: input=3, output=0, feature=0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout
re0: watchdog timeout



-- 
George Georgalis, information system scientist <IXOYE><
References:
- Nvidia MCP67 SATA controller
  - From: Dieter Baron
Prev by Date: Re: anyone working on BCM4318 or porting OpenBSD's bwi(4)?
Next by Date: Re: anyone working on BCM4318 or porting OpenBSD's bwi(4)?
Previous by Thread: Re: Nvidia MCP67 SATA controller
Next by Thread: Docking stations and ACPI?
Indexes:
Home | Main Index | Thread Index | Old Index