Subject: Problems with 1.5.2/1.6_RC and AMD network drivers
To: None <tech-kern@netbsd.org>
From: Darren Reed <darrenr@reed.wattle.id.au>
List: tech-kern
Date: 08/19/2002 09:29:02
I picked up two PCI cards with AMD network chips, on the weekend.
One is a combo card (53c875 + AMD), the other is a dual-10/100 port
network card. Both 1.5.2 & 1.6 see the SCSI fine, but I'm not sure
about the network card(s). 1.5.2 would give me le1, 1.6 gives me
a pcn1. That's two AMD network ports missing in action. Output
from boot messages (with the PCI verbose thing set) is included.
btw, is there any chance 'pcn*' can make it into GENERIC on more
platforms than just i386 for the 1.6 release ?
Some problems seen at bootup are (1.5.2):
le0 at pci1 dev 5 function 0: PCI configuration registers:
Advanced Micro Devices 79c970 PCnet-PCI LANCE Ethernet (ethernet network, revisi
on 0x33) at ? dev 5 function 0 (tag 0x12800, intrtag 0x3800, intrswiz 0x5, intrp
in 0x2, i/o off, mem on, no quirks): PCnet-PCI Ethernet
le0: can't map I/O space
(1.6_RC1)
pcn0 at pci1 dev 5 function 0: PCI configuration registers:
Advanced Micro Devices PCnet-PCI Ethernet (ethernet network, revision 0x33) at ?
dev 5 function 0 (intrswiz 0x5, intrpin 0x2, i/o off, mem on, no quirks): AMD P
Cnet-PCI Ethernet
pcn0: unable to map device registers
Darren
Entering netbsd.generic.pci at 0xfffffc00003010c0...
[ preserving 448616 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 1.5.2 (GENERIC_PCI) #0: Tue Jun 18 02:41:03 EST 2002
root@pelinor.reed.wattle.id.au:/usr/src152/sys/arch/alpha/compile/GENERIC_PCI
Digital AlphaPC 164 500 MHz
8192 byte page size, 1 processor.
total memory = 128 MB
(2472 KB reserved for PROM, 125 MB used by NetBSD)
avail memory = 111 MB
using 816 buffers containing 6528 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A-2 (pass 2)
cpu0: Architecture extensions: 1<BWX>
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (ALCOR/ALCOR2), pass 3
cia0: extended capabilities: 21<DWEN,BWEN>
cia0: using BWX for PCI config access
pci0 at cia0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
de0 at pci0 dev 5 function 0: PCI configuration registers:
Common header:
0x00: 0x00191011 0x02800047 0x02000030 0x0000ff00
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21142/21143 10/100 Ethernet (0x0019)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x30
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011081 0x82380080 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x500b1011
0x30: 0x82340000 0x00000000 0x00000000 0x28140102
Base address register at 0x10
type: i/o
base: 0x00011080, size: 0x00000080
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380080, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1011
Subsystem ID: 0x500b
Expansion ROM Base Address: 0x82340000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x28
Minimum Grant: 0x14
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x02
Device-dependent header:
0x40: 0x00000500 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21142/21143 10/100 Ethernet (ethernet network, revision 0x30) at ? dev 5 function 0 (tag 0x2800, intrtag 0x2800, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks)
de0: interrupting at eb164 irq 2
de0: DEC DE500-BA 21143 [10-100Mb/s] pass 3.0
de0: address 00:00:f8:09:4f:14
de0: enabling 100baseTX port
de1 at pci0 dev 6 function 0: PCI configuration registers:
Common header:
0x00: 0x00091011 0x02800047 0x02000022 0x0000ff00
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21140 ("FasterNet") 10/100 Ethernet (0x0009)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x22
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011001 0x82380000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x11001186
0x30: 0x82300000 0x00000000 0x00000000 0x28140100
Base address register at 0x10
type: i/o
base: 0x00011000, size: 0x00000080
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380000, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1186
Subsystem ID: 0x1100
Expansion ROM Base Address: 0x82300000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x28
Minimum Grant: 0x14
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000200 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21140 ("FasterNet") 10/100 Ethernet (ethernet network, revision 0x22) at ? dev 6 function 0 (tag 0x3000, intrtag 0x3000, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks)
de1: interrupting at eb164 irq 0
de1: 21140A [10-100Mb/s] pass 2.2
de1: address 00:40:05:30:90:4e
ppb0 at pci0 dev 7 function 0: PCI configuration registers:
Common header:
0x00: 0x00241011 0x0a900106 0x06040003 0x0001ff10
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21152 PCI-PCI Bridge (0x0024)
Command register: 0x0106
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0a90
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: on
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: PCI (0x04)
Interface: 0x00
Revision ID: 0x03
BIST: 0x00
Header Type: 0x01 (0x01)
Latency Timer: 0xff
Cache Line Size: 0x10
Type 1 (PCI-PCI bridge) header:
0x10: 0x00000000 0x00000000 0xff000100 0x228001f1
0x20: 0x82108200 0x0001fff1 0x00000000 0x00000000
0x30: 0x00000000 0x000000dc 0x00000000 0x00220000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Primary bus number: 0x00
Secondary bus number: 0x01
Subordinate bus number: 0x00
Secondary bus latency timer: 0xff
Secondary status register: 0x2280
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Signaled Target Abort: off
Received Target Abort: off
Received Master Abort: on
System Error: off
Parity Error: off
I/O region:
base register: 0xf1
limit register: 0x01
base upper 16 bits register: 0x0000
limit upper 16 bits register: 0x0000
Memory region:
base register: 0x8200
limit register: 0x8210
Prefetchable memory region:
base register: 0xfff1
limit register: 0x0001
base upper 32 bits register: 0x00000000
limit upper 32 bits register: 0x00000000
Reserved @ 0x34: 0x000000dc
Expansion ROM Base Address: 0x00000000
Interrupt line: 0x00
Interrupt pin: 0x00 (none)
Bridge control register: 0x0022
Parity error response: off
Secondary SERR forwarding: on
ISA enable: off
VGA enable: off
Master abort reporting: on
Secondary bus reset: off
Fast back-to-back capable: off
Device-dependent header:
0x40: 0x0000000c 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00003e00 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x01010001
0xe0: 0x00400000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21152 PCI-PCI Bridge (PCI bridge, revision 0x03) at ? dev 7 function 0 (tag 0x3800, intrtag 0x3800, intrswiz 0, intrpin 0, i/o off, mem on, no quirks): Digital Equipment DECchip 21152 PCI-PCI Bridge (rev. 0x03)
pci1 at ppb0 bus 1
pci1: memory space enabled, rd/line, wr/inv ok
siop0 at pci1 dev 4 function 0: PCI configuration registers:
Common header:
0x00: 0x000f1000 0x02100047 0x01000026 0x0000ff00
Vendor Name: Symbios Logic (0x1000)
Device Name: 53c875/876 (0x000f)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: SCSI (0x00)
Interface: 0x00
Revision ID: 0x26
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00010001 0x82141000 0x82140000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x10001000
0x30: 0x82100000 0x00000040 0x00000000 0x40110101
Base address register at 0x10
type: i/o
base: 0x00010000, size: 0x00000100
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82141000, size: 0x00000100
Base address register at 0x18
type: 32-bit nonprefetchable memory
base: 0x82140000, size: 0x00001000
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1000
Subsystem ID: 0x1000
Expansion ROM Base Address: 0x82100000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x40
Minimum Grant: 0x11
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x01
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00010001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x000000c0 0x0f000000 0x000d0000 0x02000080
0x90: 0x00000000 0xffffff00 0x6031f000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x0f700000 0x00000000 0x000000a7
0xd0: 0x00000000 0x00000000 0x00000000 0x00010000
0xe0: 0x826c9820 0xfff9d5a5 0x0015e001 0xe53c6cee
0xf0: 0x32402100 0xebff77b7 0x0de81f80 0xdfbde3b3
Don't know how to pretty-print device-dependent header.
Symbios Logic 53c875/876 (SCSI mass storage, revision 0x26) at ? dev 4 function 0 (tag 0x12000, intrtag 0x3800, intrswiz 0x4, intrpin 0x1, i/o off, mem on, no quirks): Symbios Logic 53c875 (ultra-wide scsi)
siop0: using on-board RAM
siop0: interrupting at eb164 irq 1
scsibus0 at siop0: 16 targets, 8 luns per target
le0 at pci1 dev 5 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02900047 0x02000033 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: 79c970 PCnet-PCI LANCE Ethernet (0x2000)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x33
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000001 0x82141100 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x106e103c
0x30: 0x82000000 0x00000040 0x00000000 0x18180108
Base address register at 0x10
type: i/o
base: 0x00000000, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82141100, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x103c
Subsystem ID: 0x106e
Expansion ROM Base Address: 0x82000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x18
Minimum Grant: 0x18
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x08
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0xff110001 0x14002000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices 79c970 PCnet-PCI LANCE Ethernet (ethernet network, revision 0x33) at ? dev 5 function 0 (tag 0x12800, intrtag 0x3800, intrswiz 0x5, intrpin 0x2, i/o off, mem on, no quirks): PCnet-PCI Ethernet
le0: can't map I/O space
sio0 at pci0 dev 8 function 0: PCI configuration registers:
Common header:
0x00: 0x04848086 0x02000007 0x00000043 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82378ZB System I/O (SIO) (0x0484)
Command register: 0x0007
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: miscellaneous (0x00)
Interface: 0x00
Revision ID: 0x43
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00f80c20 0x000f1000 0x0f1000f0 0xffc04056
0x50: 0x00000000 0x04000000 0x00000000 0x00000000
0x60: 0x80808080 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000078 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000008 0x00000000 0x0000000f 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82378ZB System I/O (SIO) (miscellaneous prehistoric, revision 0x43) at ? dev 8 function 0 (tag 0x4000, intrtag 0x4000, intrswiz 0, intrpin 0, i/o on, mem on, no quirks): Intel 82378ZB System I/O (SIO) (rev. 0x43)
le1 at pci0 dev 9 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02800047 0x02000025 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: 79c970 PCnet-PCI LANCE Ethernet (0x2000)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x25
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011101 0x82380100 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x104c103c
0x30: 0x82200000 0x00000000 0x00000000 0xff060103
Base address register at 0x10
type: i/o
base: 0x00011100, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380100, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x103c
Subsystem ID: 0x104c
Expansion ROM Base Address: 0x82200000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0xff
Minimum Grant: 0x06
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x03
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices 79c970 PCnet-PCI LANCE Ethernet (ethernet network, revision 0x25) at ? dev 9 function 0 (tag 0x4800, intrtag 0x4800, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): PCnet-PCI Ethernet
le1: address 00:60:b0:a5:d5:99
le1: 8 receive buffers, 2 transmit buffers
le1: interrupting at eb164 irq 3
pciide0 at pci0 dev 11 function 0: PCI configuration registers:
Common header:
0x00: 0x06461095 0x02800045 0x01018001 0x0000f800
Vendor Name: CMD Technology (0x1095)
Device Name: PCI0646 (0x0646)
Command register: 0x0045
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: IDE (0x01)
Interface: 0x80
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xf8
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00011121 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x04020105
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: i/o
base: 0x00011120, size: 0x00000010
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x04
Minimum Grant: 0x02
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x05
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0xc000e800 0xcc00c03f 0x0000403f 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00200000 0x40e40000 0x00200008 0x6d90501c
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
CMD Technology PCI0646 (IDE mass storage, interface 0x80, revision 0x01) at ? dev 11 function 0 (tag 0x5800, intrtag 0x5800, intrswiz 0, intrpin 0x1, i/o on, mem off, no quirks): CMD Technology PCI0646 (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <ST51270A>
wd0: drive supports 32-sector pio transfers, lba addressing
wd0: 1223 MB, 2485 cyl, 16 head, 63 sec, 512 bytes/sect x 2504880 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
pciide0: primary channel interrupting at isa irq 14
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <VI-DATA 64XM, MT1102 Firmware, VER 5.1> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: secondary channel interrupting at isa irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
scsibus0: waiting 2 seconds for devices to settle...
de1: setting full duplex.
de1: enabling Full Duplex 100baseTX port
siop0: target 2 using tagged queuing
sd0 at scsibus0 target 2 lun 0: <FUJITSU, M2909S-512, 0134> SCSI2 0/direct fixed
siop0: target 2 now synchronous at 10.0Mhz, offset 15
sd0: 2956 MB, 3138 cyl, 19 head, 101 sec, 512 bytes/sect x 6054834 sectors
root on wd0a dumps on wd0b
root file system type: ffs
Enter pathname of shell or RETURN for sh:
[3g H H H H H H H H HTerminal type is vt100.
We recommend creating a non-root account and using su(1) for root access.
# >>>
>>>boot dqa0 -fi netbsd-1-6-pci -fl s
(boot dqa0.0.0.11.0 -file netbsd-1-6-pci -flags s)
block 0 of dqa0.0.0.11.0 is a valid boot block
reading 15 blocks from dqa0.0.0.11.0
bootstrap code read in
base = 180000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 172000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 1.5.2 FFS Primary Bootstrap
|/-\|/-\|/-\Jumping to entry point...
NetBSD/alpha 1.5.2 Secondary Bootstrap, Revision 1.10
(he@albatross.urc.uninett.no, Aug 17 23:50:47 MEST 2001)
VMS PAL rev: 0x1000900010115
OSF PAL rev: 0x1000800020117
Switch to OSF PAL code succeeded.
Boot file: netbsd-1-6-pci
Boot flags: s
Entering netbsd-1-6-pci at 0xfffffc00003012e0...
[ using 559648 bytes of netbsd ELF symbol table ]
consinit: not using prom console
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 1.6_RC1 (GENERIC_PCI) #2: Tue Jun 18 11:09:55 EST 2002
root@:/usr/src/sys/arch/alpha/compile/GENERIC_PCI
Digital AlphaPC 164 500 MHz, s/n
8192 byte page size, 1 processor.
total memory = 128 MB
(2472 KB reserved for PROM, 125 MB used by NetBSD)
avail memory = 110 MB
using 816 buffers containing 6528 KB of memory
mainbus0 (root)
cpu0 at mainbus0: ID 0 (primary), 21164A-2
cpu0: Architecture extensions: 1<BWX>
cia0 at mainbus0: DECchip 2117x Core Logic Chipset (ALCOR/ALCOR2), pass 3
cia0: extended capabilities: 21<DWEN,BWEN>
cia0: using BWX for PCI config access
pci0 at cia0 bus 0
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
tlp0 at pci0 dev 5 function 0: PCI configuration registers:
Common header:
0x00: 0x00191011 0x02800047 0x02000030 0x0000ff00
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21142/21143 10/100 Ethernet (0x0019)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x30
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011081 0x82380080 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x500b1011
0x30: 0x82340000 0x00000000 0x00000000 0x28140102
Base address register at 0x10
type: 32-bit i/o
base: 0x00011080, size: 0x00000080
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380080, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1011
Subsystem ID: 0x500b
Expansion ROM Base Address: 0x82340000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x28
Minimum Grant: 0x14
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x02
Device-dependent header:
0x40: 0x00000500 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21142/21143 10/100 Ethernet (ethernet network, revision 0x30) at ? dev 5 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): DECchip 21143 Ethernet, pass 3.0
tlp0: interrupting at eb164 irq 2
tlp0: DEC DE500-BA, Ethernet address 00:00:f8:09:4f:14
tlp0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp1 at pci0 dev 6 function 0: PCI configuration registers:
Common header:
0x00: 0x00091011 0x02800047 0x02000022 0x0000ff00
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21140 ("FasterNet") 10/100 Ethernet (0x0009)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x22
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011001 0x82380000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x11001186
0x30: 0x82300000 0x00000000 0x00000000 0x28140100
Base address register at 0x10
type: 32-bit i/o
base: 0x00011000, size: 0x00000080
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380000, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1186
Subsystem ID: 0x1100
Expansion ROM Base Address: 0x82300000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x28
Minimum Grant: 0x14
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000200 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21140 ("FasterNet") 10/100 Ethernet (ethernet network, revision 0x22) at ? dev 6 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): DECchip 21140A Ethernet, pass 2.2
tlp1: interrupting at eb164 irq 0
tlp1: Ethernet address 00:40:05:30:90:4e
nsphy0 at tlp1 phy 8: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb0 at pci0 dev 7 function 0: PCI configuration registers:
Common header:
0x00: 0x00241011 0x0a900106 0x06040003 0x0001ff10
Vendor Name: Digital Equipment (0x1011)
Device Name: DECchip 21152 PCI-PCI Bridge (0x0024)
Command register: 0x0106
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0a90
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: on
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: PCI (0x04)
Interface: 0x00
Revision ID: 0x03
BIST: 0x00
Header Type: 0x01 (0x01)
Latency Timer: 0xff
Cache Line Size: 0x10
Type 1 (PCI-PCI bridge) header:
0x10: 0x00000000 0x00000000 0xff000100 0x228001f1
0x20: 0x82108200 0x0001fff1 0x00000000 0x00000000
0x30: 0x00000000 0x000000dc 0x00000000 0x00220000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Primary bus number: 0x00
Secondary bus number: 0x01
Subordinate bus number: 0x00
Secondary bus latency timer: 0xff
Secondary status register: 0x2280
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Signaled Target Abort: off
Received Target Abort: off
Received Master Abort: on
System Error: off
Parity Error: off
I/O region:
base register: 0xf1
limit register: 0x01
base upper 16 bits register: 0x0000
limit upper 16 bits register: 0x0000
Memory region:
base register: 0x8200
limit register: 0x8210
Prefetchable memory region:
base register: 0xfff1
limit register: 0x0001
base upper 32 bits register: 0x00000000
limit upper 32 bits register: 0x00000000
Reserved @ 0x34: 0x000000dc
Expansion ROM Base Address: 0x00000000
Interrupt line: 0x00
Interrupt pin: 0x00 (none)
Bridge control register: 0x0022
Parity error response: off
Secondary SERR forwarding: on
ISA enable: off
VGA enable: off
Master abort reporting: on
Secondary bus reset: off
Fast back-to-back capable: off
Device-dependent header:
0x40: 0x0000000c 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00003e00 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x01010001
0xe0: 0x00400000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Digital Equipment DECchip 21152 PCI-PCI Bridge (PCI bridge, revision 0x03) at ? dev 7 function 0 (intrswiz 0, intrpin 0, i/o off, mem on, no quirks): Digital Equipment DECchip 21152 PCI-PCI Bridge (rev. 0x03)
pci1 at ppb0 bus 1
pci1: memory space enabled, rd/line, wr/inv ok
siop0 at pci1 dev 4 function 0: PCI configuration registers:
Common header:
0x00: 0x000f1000 0x02100047 0x01000026 0x0000ff00
Vendor Name: Symbios Logic (0x1000)
Device Name: 53c875/876 (0x000f)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: SCSI (0x00)
Interface: 0x00
Revision ID: 0x26
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00010001 0x82141000 0x82140000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x10001000
0x30: 0x82100000 0x00000040 0x00000000 0x40110101
Base address register at 0x10
type: 32-bit i/o
base: 0x00010000, size: 0x00000100
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82141000, size: 0x00000100
Base address register at 0x18
type: 32-bit nonprefetchable memory
base: 0x82140000, size: 0x00001000
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1000
Subsystem ID: 0x1000
Expansion ROM Base Address: 0x82100000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x40
Minimum Grant: 0x11
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x01
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00010001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x350000da 0x0f020f47 0x00820000 0x020f0080
0x90: 0xffffffff 0xffffff00 0x6135f000 0x82140560
0xa0: 0x00200000 0x54000000 0x82140218 0x82140220
0xb0: 0xfffffe38 0x20000000 0xa100ff8c 0x82140058
0xc0: 0x0000848f 0x0f7000c4 0x0080000b 0x80000c76
0xd0: 0x80000000 0x80000000 0x80000000 0x40ff2d9c
0xe0: 0x826c9820 0xfff9d5a5 0x0015e001 0xe53c6cee
0xf0: 0x32402100 0xebff77b7 0x0de81f80 0xdfbde3b3
Don't know how to pretty-print device-dependent header.
Symbios Logic 53c875/876 (SCSI mass storage, revision 0x26) at ? dev 4 function 0 (intrswiz 0x4, intrpin 0x1, i/o off, mem on, no quirks): Symbios Logic 53c875 (ultra-wide scsi)
siop0: using on-board RAM
siop0: interrupting at eb164 irq 1
scsibus0 at siop0: 16 targets, 8 luns per target
pcn0 at pci1 dev 5 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02900047 0x02000033 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: PCnet-PCI Ethernet (0x2000)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x33
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000001 0x82141100 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x106e103c
0x30: 0x82000000 0x00000040 0x00000000 0x18180108
Base address register at 0x10
type: 32-bit i/o
base: 0x00000000, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82141100, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x103c
Subsystem ID: 0x106e
Expansion ROM Base Address: 0x82000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x18
Minimum Grant: 0x18
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x08
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0xff110001 0x14002000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices PCnet-PCI Ethernet (ethernet network, revision 0x33) at ? dev 5 function 0 (intrswiz 0x5, intrpin 0x2, i/o off, mem on, no quirks): AMD PCnet-PCI Ethernet
pcn0: unable to map device registers
sio0 at pci0 dev 8 function 0: PCI configuration registers:
Common header:
0x00: 0x04848086 0x02000007 0x00000043 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82378ZB System I/O (SIO) (0x0484)
Command register: 0x0007
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: miscellaneous (0x00)
Interface: 0x00
Revision ID: 0x43
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00f00c20 0x000f1000 0x0f1000f0 0xffc04056
0x50: 0x00000000 0x04000000 0x00000000 0x00000000
0x60: 0x80808080 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000078 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000008 0x00000000 0x0000000f 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82378ZB System I/O (SIO) (miscellaneous prehistoric, revision 0x43) at ? dev 8 function 0 (intrswiz 0, intrpin 0, i/o on, mem on, no quirks): Intel 82378ZB System I/O (SIO) (rev. 0x43)
pcn1 at pci0 dev 9 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02800047 0x02000025 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: PCnet-PCI Ethernet (0x2000)
Command register: 0x0047
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x25
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00011101 0x82380100 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x104c103c
0x30: 0x82200000 0x00000000 0x00000000 0xff060103
Base address register at 0x10
type: 32-bit i/o
base: 0x00011100, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x82380100, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x103c
Subsystem ID: 0x104c
Expansion ROM Base Address: 0x82200000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0xff
Minimum Grant: 0x06
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x03
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices PCnet-PCI Ethernet (ethernet network, revision 0x25) at ? dev 9 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): AMD PCnet-PCI Ethernet
pcn1: Am79c971 PCnet-FAST rev 5, Ethernet address 00:60:b0:a5:d5:99
pcn1: interrupting at eb164 irq 3
nsphy1 at pcn1 phy 1: DP83840 10/100 media interface, rev. 1
nsphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pciide0 at pci0 dev 11 function 0: PCI configuration registers:
Common header:
0x00: 0x06461095 0x02800045 0x01018001 0x0000f800
Vendor Name: CMD Technology (0x1095)
Device Name: PCI0646 (0x0646)
Command register: 0x0045
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: IDE (0x01)
Interface: 0x80
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xf8
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00011121 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x04020105
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: 32-bit i/o
base: 0x00011120, size: 0x00000010
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x04
Minimum Grant: 0x02
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x05
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0xc000e800 0xcc00c03f 0x0000403f 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00200008 0x41190000 0x00200008 0x6d90501c
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
CMD Technology PCI0646 (IDE mass storage, interface 0x80, revision 0x01) at ? dev 11 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem off, no quirks): CMD Technology PCI0646 (rev. 0x01)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
wd0 at pciide0 channel 0 drive 0: <ST51270A>
wd0: drive supports 32-sector PIO transfers, LBA addressing
wd0: 1223 MB, 2485 cyl, 16 head, 63 sec, 512 bytes/sect x 2504880 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
pciide0: primary channel interrupting at isa irq 14
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
atapibus0 at pciide0 channel 1: 2 targets
cd0 at atapibus0 drive 0: <VI-DATA 64XM, MT1102 Firmware, VER 5.1> type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
pciide0: secondary channel interrupting at isa irq 15
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
isa0 at sio0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
lpt0 at isa0 port 0x3bc-0x3bf irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
isabeep0 at pcppi0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
mcclock0 at isa0 port 0x70-0x71: mc146818 or compatible
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 2 lun 0: <FUJITSU, M2909S-512, 0134> SCSI2 0/direct fixed
sd0: 2956 MB, 3138 cyl, 19 head, 101 sec, 512 bytes/sect x 6054834 sectors
sd0: sync (100.0ns offset 15), 8-bit (10.000MB/s) transfers, tagged queueing
Kernelized RAIDframe activated
root on wd0a dumps on wd0b
root file system type: ffs
Enter pathname of shell or RETURN for sh: