Dnia Wed, 18 Oct 2006 15:50:41 +0200
Marcin Zieciak <ymarg@lubin.edu.pl> napisa=B3(a):

> Czy mam wnioskowa=E6, =BFe =BCle podpi=B1=B3em dyski do kontrolera, i dla=
tego
> ich nie wida=E6, czy jest jakie=B6 magiczne polecenie, kt=F3re sprawia, =
=BFe
> b=EAd=B1 one widoczne?

Sprawd=BC jak to wygl=B1da u Ciebie na GENERICu?

[K240 ~]# dmesg | grep -E 'ide|ahc|^(sd|wd)' | sort
ahc0 at pci2 dev 4 function 0: Adaptec aic7890/91 Ultra2 SCSI adapter
ahc0: aic7890/91: Ultra2 Wide Channel A, SCSI Id=3D7, 32/253 SCBs
ahc0: interrupting at ioapic1 pin 15 (irq 14)
atabus0 at hptide0 channel 0
atabus1 at hptide0 channel 1
hptide0 at pci1 dev 6 function 0
hptide0: Triones/Highpoint HPT370 IDE Controller
hptide0: bus-master DMA support present
hptide0: primary channel wired to native-PCI mode
hptide0: secondary channel wired to native-PCI mode
hptide0: using ioapic1 pin 12 (irq 10) for native-PCI interrupt
scsibus0 at ahc0: 16 targets, 8 luns per target
sd0 at scsibus0 target 0 lun 0: <COMPAQ, HD0093172C, 3208> disk fixed
sd0: 8678 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17773500 sectors
sd0: sync (50.00ns offset 15), 16-bit (40.000MB/s) transfers, tagged queuei=
ng
sd1 at scsibus0 target 1 lun 0: <COMPAQ, HD0093172C, 3208> disk fixed
sd1: 8678 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17773500 sectors
sd1: sync (50.00ns offset 15), 16-bit (40.000MB/s) transfers, tagged queuei=
ng
sd2 at scsibus0 target 2 lun 0: <COMPAQ, BB00911CA0, 3B05> disk fixed
sd2: 8678 MB, 5273 cyl, 20 head, 168 sec, 512 bytes/sect x 17773524 sectors
sd2: sync (50.00ns offset 15), 16-bit (40.000MB/s) transfers, tagged queuei=
ng
sd3 at scsibus0 target 3 lun 0: <COMPAQ, HB00931B93, A193> disk fixed
sd3: 8678 MB, 5273 cyl, 20 head, 168 sec, 512 bytes/sect x 17773500 sectors
sd3: sync (50.00ns offset 31), 16-bit (40.000MB/s) transfers, tagged queuei=
ng
wd0 at atabus0 drive 0: <SAMSUNG SV0802N>
wd0(hptide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd0: 32-bit data port
wd0: 76351 MB, 155127 cyl, 16 head, 63 sec, 512 bytes/sect x 156368016 sect=
ors
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus1 drive 0: <ST3802110A>
wd1(hptide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wd1: 32-bit data port
wd1: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sect=
ors
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)

dyski powinny by=E6 widoczne bez zb=EAdnych zabieg=F3w, je=B6li tylko kontr=
oler je prawido=B3owo=20
wykrywa.
--=20
: Jacek 'Szumak' Kotlarski ::: < szumak at oksywienet org pl > :
: Unix Administrator : GG 2052377 : Stowarzyszenie OKSYWIE_NET :