Re: Sun Fire v120, satalink etc.

[Dave McGuire <mcguire%neurotica.com@localhost>]

  Nice!

  (and nice to see some traffic on this list!)

          -Dave

On 09/17/2013 10:14 AM, Michael wrote:
> Hello,
> 
> just for the record, that's my new toy:
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2
> 004, 2005,
>     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
> 
> NetBSD 6.99.23 (BRANCA) #0: Sun Sep  8 10:54:55 EDT 2013
>         ml@connemara:/home/build/obj_sparc64/sys/arch/sparc64/compile/BRANCA
> total memory = 2048 MB
> avail memory = 2000 MB
> timecounter: Timecounters tick every 10.000 msec
> mainbus0 (root): SUNW,UltraAX-i2 (Sun Fire V120): hostid 8335d0de
> cpu0 at mainbus0: SUNW,UltraSPARC-IIe @ 648 MHz, UPA id 0
> cpu0: system tick frequency 11 MHz
> cpu0: 16K instruction (32 b/l), 16K data (32 b/l), 512K external (64 b/l)
> psycho0 at mainbus0
> psycho0: SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
> psycho_alloc_extent: no "available" property
> psycho_alloc_extent: no "available" property
> pci0 at psycho0
> pci0: i/o space, memory space enabled
> ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI Bridge (rev. 0x13)
> pci1 at ppb0 bus 1
> pci1: i/o space, memory space enabled
> ebus0 at pci1 dev 12 function 0
> ebus0: Sun Microsystems PCIO Ebus2 (US III), revision 0x01
> flashprom at ebus0 addr 0-fffff not configured
> clock0 at ebus0 addr 0-1fff: mk48t59
> ebus_attach: idprom: incomplete
> lom0 at ebus0 addr 200000-200003 ipl 2a: SUNW,lomh: LOMlite2 rev 3.12
> lom0: 4 fan(s), 1 PSU(s), 1 temp sensor(s)
> lom0: Watchdog timer configured.
> alipm0 at pci1 dev 3 function 0: 74KHz clock
> iic0 at alipm0: I2C bus
> admtemp0 at iic0 addr 0x18: ADM1021 or compatible environmental sensor
> spdmem0 at iic0 addr 0x54
> spdmem0: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
> spdmem0: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
> spdmem0: tAA-tRCD-tRP-tRAS: 3-15-15-37
> spdmem0: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
> spdmem1 at iic0 addr 0x55
> spdmem1: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
> spdmem1: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
> spdmem1: tAA-tRCD-tRP-tRAS: 3-15-15-37
> spdmem1: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
> spdmem2 at iic0 addr 0x56
> spdmem2: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
> spdmem2: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
> spdmem2: tAA-tRCD-tRP-tRAS: 3-15-15-37
> spdmem2: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
> spdmem3 at iic0 addr 0x57
> spdmem3: SDRAM (registered), data ECC, 512MB, 133MHz (PC-133)
> spdmem3: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
> spdmem3: tAA-tRCD-tRP-tRAS: 3-15-15-37
> spdmem3: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
> seeprom0 at iic0 addr 0x50: i2c-nvram: size 8192
> seeprom1 at iic0 addr 0x51: motherboard-fru: size 8192
> ebus1 at pci1 dev 7 function 0
> ebus1: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
> power at ebus1 addr 800-82f ipl 25 not configured
> com0 at ebus1 addr 3f8-3ff ipl 2b: ns16550a, working fifo
> com0: console
> com1 at ebus1 addr 2e8-2ef ipl 2b: ns16550a, working fifo
> gem0 at pci1 dev 12 function 1: Sun Microsystems ERI Ethernet (rev. 0x01)
> gem0: interrupting at ivec 3006
> ukphy0 at gem0 phy 1: OUI 0x0008bb, model 0x0002, rev. 1
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> gem0: Ethernet address 00:03:ba:35:d0:de, 2KB RX fifo, 2KB TX fifo
> ohci0 at pci1 dev 12 function 3: Sun Microsystems USB Controller (rev. 0x01)
> ohci0: interrupting at ivec 24
> ohci0: OHCI version 1.0, legacy support
> usb0 at ohci0: USB revision 1.0
> aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 
> 0xc3)
> aceride0: bus-master DMA support present
> aceride0: using PIO transfers above 137GB as workaround for 48bit DMA access 
> bug, expect reduced performance
> aceride0: primary channel configured to native-PCI mode
> aceride0: using ivec 180c for native-PCI interrupt
> atabus0 at aceride0 channel 0
> aceride0: secondary channel configured to native-PCI mode
> atabus1 at aceride0 channel 1
> gem1 at pci1 dev 5 function 1: Sun Microsystems ERI Ethernet (rev. 0x01)
> gem1: interrupting at ivec 301c
> ukphy1 at gem1 phy 1: OUI 0x0008bb, model 0x0002, rev. 1
> ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> gem1: Ethernet address 00:03:ba:35:d0:de, 2KB RX fifo, 2KB TX fifo
> ohci1 at pci1 dev 5 function 3: Sun Microsystems USB Controller (rev. 0x01)
> ohci1: interrupting at ivec 26
> ohci1: OHCI version 1.0, legacy support
> usb1 at ohci1: USB revision 1.0
> ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI Bridge (rev. 0x13)
> pci2 at ppb1 bus 2
> pci2: i/o space, memory space enabled
> esiop0 at pci2 dev 8 function 0: Symbios Logic 53c896 (ultra2-wide scsi)
> esiop0: using on-board RAM
> esiop0: interrupting at ivec 1820
> scsibus0 at esiop0: 16 targets, 8 luns per target
> esiop1 at pci2 dev 8 function 1: Symbios Logic 53c896 (ultra2-wide scsi)
> esiop1: using on-board RAM
> esiop1: interrupting at ivec 1820
> scsibus1 at esiop1: 16 targets, 8 luns per target
> satalink0 at pci2 dev 5 function 0: Silicon Image SATALink 3512 (rev. 0x01)
> satalink0: SATALink BA5 register space disabled
> satalink0: bus-master DMA support present
> satalink0: primary channel wired to native-PCI mode
> satalink0: using ivec 15 for native-PCI interrupt
> atabus2 at satalink0 channel 0
> satalink0: secondary channel wired to native-PCI mode
> atabus3 at satalink0 channel 1
> pcons at mainbus0 not configured
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
> timecounter: Timecounter "tick-counter" frequency 648000000 Hz quality 100
> timecounter: Timecounter "stick-counter" frequency 11111111 Hz quality 200
> No counter-timer -- using STICK at 11MHz as system clock.
> scsibus0: waiting 2 seconds for devices to settle...
> scsibus1: waiting 2 seconds for devices to settle...
> satalink0: port 0: device present, speed: 1.5Gb/s
> wd0 at atabus2 drive 0
> uhub0 at usb0: Sun Microsystems OHCI root hub, class 9/0, rev 1.00/1.00, addr 
> 1
> uhub0: 4 ports with 4 removable, self powered
> uhub1 at usb1: Sun Microsystems OHCI root hub, class 9/0, rev 1.00/1.00, addr 
> 1
> uhub1: 4 ports with 4 removable, self powered
> wd0: <WDC WD5000AVDS-73U7B1>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
> wd0(satalink0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
> sd0 at scsibus0 target 0 lun 0: <NETAPP, X243_FAL7E073S10, NA00> disk fixed
> sd0: 70092 MB, 29902 cyl, 8 head, 600 sec, 512 bytes/sect x 143550456 sectors
> sd0: sync (25.00ns offset 31), 16-bit (80.000MB/s) transfers, tagged queueing
> 
> wd0 is an external disk hooked to a cheap SiI eSATA card. So, satalink Just 
> Works(tm). Anything faster than 1.5GBit/s wouldn't make much sense anyway 
> since the PCI slot is 32bit/33MHz and that disk can pretty much saturate it.
> 
> have fun
> Michael
> 


-- 
Dave McGuire, AK4HZ
New Kensington, PA