Re: Netra X1 with WD0 and AcerIDE

["Maurizio Caloro" <mauric%gmx.ch@localhost>]

Hello together
After step by step like this documentation http://www.netbsd.org/docs/kernel/ i 
become a break /sbin/init: error 8

with config -x Netbsd compare the existing and the New GENERIC kernel and no 
diversity appair

Please help Thanks
mauri

NetraX1# file /usr/src/sys/arch/sparc64/compile/GENERIC32/netbsd /sbin/init
/usr/src/sys/arch/sparc64/compile/GENERIC32/netbsd: 
ELF 32-bit MSB executable, SPARC32PLUS, version 1 (SYSV), statically linked, 
for NetBSD 5.1, not stripped
/sbin/init:
ELF 64-bit MSB executable, SPARC V9, relaxed memory ordering, version 1 (SYSV), 
dynamically linked (uses shared libs), for NetBSD 5.1, not stripped
NetraX1#


ok boot Nnetbsd -v [<-- newone]

Sun Netra X1 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1024 MB memory installed, Serial #51354397.
Ethernet address 0:3:ba:f:9b:1d, Host ID: 830f9b1d.

Executing last command: boot Nnetbsd -v
Boot device: /pci@1f,0/ide@d/disk@0,0  File and args: Nnetbsd -v
NetBSD IEEE 1275 Bootblock
>> NetBSD/sparc64 OpenFirmware Boot, Revision 1.13
=0x848cbc
Loading Nnetbsd: 7735810+298120+349136 [350096+337273]=0x9461a8
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1_RC4 (GENERIC32) #0: Wed Oct 27 06:01:54 CEST 2010
        root@NetraX1.:/usr/src/sys/arch/sparc64/compile/GENERIC32
total memory = 1024 MB
avail memory = 998 MB
mainbus0 (root): SUNW,UltraAX-i2 (Sun Netra X1): hostid 830f9b1d
cpu0 at mainbus0: SUNW,UltraSPARC-IIe @ 500 MHz, UPA id 0
cpu0: 16K instruction (32 b/l), 16K data (32 b/l), 256K external (64 b/l)
psycho0 at mainbus0
psycho0: SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 0; PCI bus 0
DVMA map: 60000000 to 80000000
IOTSB: 40b60000 to 40be0000
pci0 at psycho0
pci0: i/o space, memory space enabled
ebus0 at pci0 dev 7 function 0
ebus0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
dma at ebus0 addr 0-ffff ipl 42 not configured
rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819
power at ebus0 addr 2000-2007 ipl 35 not configured
lom0 at ebus0 addr 8010-8011 ipl 42: SUNW,lomh: LOMlite2 rev 3.10
lom0: 1 fan(s), 1 PSU(s), 1 temp sensor(s)
lom0: Watchdog timer configured.
com0 at ebus0 addr 3f8-3ff ipl 43: ns16550a, working fifo
com0: console
com1 at ebus0 addr 2e8-2ef ipl 43: ns16550a, working fifo
flashprom at ebus0 addr 0-7ffff not configured
alipm0 at pci0 dev 3 function 0: 74KHz clock
iic0 at alipm0: I2C bus
spdmem0 at iic0 addr 0x56
spdmem0: SDRAM memory, data ECC, 512MB, 133MHz (PC-1100)
spdmem0: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem0: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x57
spdmem1: SDRAM memory, data ECC, 512MB, 133MHz (PC-1100)
spdmem1: 13 rows, 11 cols, 1 banks, 4 banks/chip, 7.5ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 3-20-20-45
spdmem1: voltage LvTTL (not 5V tolerant), refresh time 7.8us (self-refreshing)
admtemp0 at iic0 addr 0x18: ADM1021 or compatible environmental sensor
tlp0 at pci0 dev 12 function 0: Davicom DM9102A Ethernet, pass 3.1
tlp0: interrupting at ivec 3006
tlp0: Ethernet address 00:03:ba:0f:9b:1d
dmphy0 at tlp0 phy 1: DM9102 10/100 media interface, rev. 0
dmphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp1 at pci0 dev 5 function 0: Davicom DM9102A Ethernet, pass 3.1
tlp1: interrupting at ivec 301c
tlp1: Ethernet address 00:03:ba:0f:9b:1d
dmphy1 at tlp1 phy 1: DM9102 10/100 media interface, rev. 0
dmphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0 at pci0 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 
0x03)
ohci0: interrupting at ivec 24
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
aceride0 at pci0 dev 13 function 0
aceride0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc3)
aceride0: bus-master DMA support present, but unused (forced off by config file)
aceride0: primary channel configured to native-PCI mode
aceride0: using ivec 180c for native-PCI interrupt
atabus0 at aceride0 channel 0
aceride0: secondary channel configured to native-PCI mode
atabus1 at aceride0 channel 1
pcons at mainbus0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tick-counter" frequency 500000000 Hz quality 100
No counter-timer -- using %tick at 500MHz as system clock.
uhub0 at usb0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wd0 at atabus0 drive 0: <ST3250823A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(aceride0:0:0): using PIO mode 4
Kernelized RAIDframe activated
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
root on wd0a dumps on wd0b
root file system type: ffs
exec /sbin/init: error 8
init: trying /sbin/oinit
exec /sbin/oinit: error 2
init: trying /sbin/init.bak
exec /sbin/init.bak: error 2
init path (default /sbin/init):


-------- Original-Nachricht --------
> Datum: Thu, 28 Oct 2010 05:46:54 +0900 (JST)
> Von: Takeshi Nakayama <tn%catvmics.ne.jp@localhost>
> An: mauric%gmx.ch@localhost
> CC: martin%duskware.de@localhost, port-sparc64%NetBSD.org@localhost
> Betreff: Re: Netra X1 with WD0 and AcerIDE

> >>> "Maurizio Caloro" <mauric%gmx.ch@localhost> wrote
> 
> > Hello together
> > i try now with both Version one with Kernel modifi and the oder change
> with aceride.c change and all the same Error apiar ?
> > 
> > Please help
> > Maurizio
> > 
> (snip)
> > exec /sbin/init: error 8
> 
> Errno 8 is "ENOEXEC Exec format error", so something is wrong with
> your kernel or init.
> 
> Please show the output of:
>        file /netbsd /sbin/init
>        config -x /netbsd
> 
> And also try to boot kernel with verbose (-v) option.
> 
> -- Takeshi Nakayama

-- 
GMX.ch - Schweizer FreeMail-Dienst mit Ãber 800.000 Mitgliedern
E-Mail & mehr! Kostenlos: http://portal.gmx.net/de/go/chfreemail