--QRj9sO5tAVLaXnSD
Content-Type: text/plain; charset=iso-8859-15
Content-Disposition: inline
Content-Transfer-Encoding: quoted-printable

Hi,

I have a quad card in my Ultra5 that has it network transfer rate limited t=
o about 200K/s.
I first thought it might be the cable, so I changed it, same problem.
I connected my laptop via X-cable, same problem.
I changed the switch port, same problem.
I tested another quad port (normal hme1 and tested hme4) same problem.

The card is :
################################
002:01:0: Digital Equipment DC21153 PCI-PCI Bridge (PCI bridge, revision 0x=
04)
#
Sun Microsystems PCIO Ebus2 (miscellaneous bridge, revision 0x01) at pci3 d=
ev 0 function 0
 not configured
hme1 at pci3 dev 0 function 1: Sun Happy Meal Ethernet, rev. 1
hme1: interrupting at ivec 3011
hme1: Ethernet address 08:00:20:a7:e9:31
ukphy0 at hme1 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0006b8, model 0x000c, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Sun Microsystems PCIO Ebus2 (miscellaneous bridge, revision 0x01) at pci3 d=
ev 1 function 0
 not configured
hme2 at pci3 dev 1 function 1: Sun Happy Meal Ethernet, rev. 1
hme2: interrupting at ivec 3012
hme2: Ethernet address 08:00:20:a7:e9:31
ukphy1 at hme2 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x0006b8, model 0x000c, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Sun Microsystems PCIO Ebus2 (miscellaneous bridge, revision 0x01) at pci3 d=
ev 2 function 0
 not configured
hme3 at pci3 dev 2 function 1: Sun Happy Meal Ethernet, rev. 1
hme3: interrupting at ivec 3013
hme3: Ethernet address 08:00:20:a7:e9:31
ukphy2 at hme3 phy 1: Generic IEEE 802.3u media interface
ukphy2: OUI 0x0006b8, model 0x000c, rev. 1
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Sun Microsystems PCIO Ebus2 (miscellaneous bridge, revision 0x01) at pci3 d=
ev 3 function 0
 not configured
hme4 at pci3 dev 3 function 1: Sun Happy Meal Ethernet, rev. 1
hme4: interrupting at ivec 3010
hme4: Ethernet address 08:00:20:a7:e9:31
ukphy3 at hme4 phy 1: Generic IEEE 802.3u media interface
ukphy3: OUI 0x0006b8, model 0x000c, rev. 1
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
################################

The speed and duplex look good :
################################
# ifconfig hme1
hme1: flags=3D8a63<UP,BROADCAST,NOTRAILERS,RUNNING,ALLMULTI,SIMPLEX,MULTICA=
ST> mtu 1500
        capabilities=3D66<TCP4CSUM,UDP4CSUM,TCP4CSUM_Rx,UDP4CSUM_Rx>
        enabled=3D0
        address: xx:xx:xx:xx:xx:xx
        media: Ethernet autoselect (100baseTX full-duplex)
        status: active
        inet n.n.n.n netmask 0xffffff00 broadcast n.n.n.n

# netstat -I hme1
Name  Mtu   Network       Address              Ipkts Ierrs    Opkts Oerrs C=
olls
hme1  1500  <Link>        xx:xx:xx:xx:xx:xx  2671531     0  2321145     0  =
   0
hme1  1500  n/24         bagheera            2671531     0  2321145     0  =
   0
################################

Any ideas or I can consider this card is dead ?

TIA,
	Jo
--=20
,- This mail runs ------.
`--------- NetBSD/i386 -'

--QRj9sO5tAVLaXnSD
Content-Type: application/pgp-signature
Content-Disposition: inline

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.1 (NetBSD)

iD8DBQFCrcgN0/VH7L7F7Y4RAvyFAJwL1JQa5ytGJxqNlZ/sd0WQNYlI/wCfTCZq
LLDcYr044To5sdX8ABuWXSc=
=3Ns5
-----END PGP SIGNATURE-----

--QRj9sO5tAVLaXnSD--