Subject: Re: support for AHA-29160 ?
To: ptiJo <ptiJo@noos.fr>
From: Adrien Auzanneau <ada@netbsd-fr.org>
List: port-sparc64
Date: 05/19/2003 23:26:01
Hi,
I'm new in sparc world.
I've got an Ultra5, i've add an adaptec 29160 SCSI pci adaptater on it
and an hdd. I've install NetBSD 1.6R on it. All ok...
Just Openboot don't reconize the scsi.
Any other way than boot from cd, or do a floppy ?
Thanks.
On (19/05/03 22:54), ptiJo wrote:
> Date: Mon, 19 May 2003 22:54:15 +0200
> From: ptiJo <ptiJo@noos.fr>
> To: port-sparc64@netbsd.org
> Cc: Emre Yildirim <emre@uab.edu>
> Subject: Re: support for AHA-29160 ?
>
> right, so I gave it a try and... it fails ;(
> in fact, it loops "into the kernel" (check end of mail).
>
> if anyone has a clue of what's happening and how to solve this...
> for infos, I did boot the machine with linux/debian and it didn't loop
> (so I guess it's not a hardware problem)
>
> thanks for answers,
> Jo
>
> On Fri, Mar 28 2003 - 13:04, Emre Yildirim wrote:
> > > On Thu, Mar 27, 2003 at 10:57:37PM +0100, ptiJo wrote:
> > >> Hi,
> > >>
> > >> I have an Ultra5 running OpenBSD/sparc64 :
> > >> ****************************************************
> > >> mainbus0 (root): SUNW,Ultra-5_10
> > >> cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 333 MHz, version 0 FPU
> > >> cpu0: physical 32K instruction (32 b/l), 16K data (32 b/l), 2048K
> > >> external (64 b/l) <SNIP>
> > >> scsibus1 at isp0: 16 targets
> > >> "Adaptec AHA-29160 U160" rev 0x02 at pci2 dev 3 function 0 not
> > >> configured ****************************************************
> > >>
> > >> is the AHA-29160 better supported on NetBSD/sparc64 ?
> >
> > Most of NetBSD device drivers are machine-independent. That means if your
> > Ultra5 uses a PCI bus (which I'm sure it does) any PCI card that is
> > supported by NetBSD should work. That particular card is not listed under
> > the supported hardware list, but the AHA-294x is...so I'm sure it will
> > work. You can give it a try and see what happens.
> >
> > take care
> >
>
> **** BOOT PROCESS ***
>
> NetBSD 1.6.1 (INSTALL) #0: Mon Apr 7 10:47:36 UTC 2003
> autobuild@cs20.apochromatic.org:/autobuilder/build/netbsd-1-6/sparc64/OBJ/autobuilderL
> total memory = 256 MB
> avail memory = 224 MB
> using 1651 buffers containing 13208 KB of memory
> bootpath: /pci@1f,0/pci@1,1/network@1,1
> mainbus0 (root): SUNW,Ultra-5_10
> cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 333 MHz, version 0 FPU
> cpu0: physical 32K instruction (32 b/l), 16K data (32 b/l), 2048K external (64 b/l)
> psycho0 at mainbus0 addr 0xfffc4000
> SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
> intr_establish: intr reused 7c0
> DVMA map: c0000000 to e0000000
> IOTSB: 112ac000 to 1132c000
> pci0 at psycho0
> pci0: i/o space, memory space enabled
> ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI bridge (rev. 0x13)
> pci1 at ppb0 bus 1
> pci1: i/o space, memory space enabled
> ebus0 at pci1 dev 1 function 0
> ebus0: Sun Microsystems PCIO Ebus2, revision 0x01
> auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-73
> power at ebus0 addr 724000-724003 ipl 37 not configured
> SUNW,pll at ebus0 addr 504000-504002 not configured
> se at ebus0 addr 400000-40007f ipl 43 not configured
> com0 at ebus0 addr 3083f8-3083ff ipl 41: ns16550a, working fifo
> kbd0 at com0
> com1 at ebus0 addr 3062f8-3062ff ipl 42: ns16550a, working fifo
> ms0 at com1
> lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ipl 34
> fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 not configured
> clock0 at ebus0 addr 0-1fff: mk48t59: hostid 80a7e931
> flashprom at ebus0 addr 0-fffff not configured
> audiocs0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 722000-722003 ipl 35 A
> audio0 at audiocs0: full duplex
> hme0 at pci1 dev 1 function 1: Sun Happy Meal Ethernet, rev. 1
> hme0: interrupting at ivec 3021
> hme0: Ethernet address 08:00:20:a7:e9:31
> nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
> nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> ATI Technologies 3D Rage Pro (VGA display, revision 0x5c) at pci1 dev 2 function 0 not cod
> pciide0 at pci1 dev 3 function 0: CMD Technology PCI0646 (rev. 0x03)
> pciide0: bus-master DMA support present
> pciide0: primary channel configured to native-PCI mode
> pciide0: using ivec 1820 for native-PCI interrupt
> wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALLP LM30>
> wd0: drive supports 16-sector PIO transfers, LBA addressing
> wd0: 28629 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 58633344 sectors
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
> wd1 at pciide0 channel 0 drive 1: <IC35L040AVER07-0>
> wd1: drive supports 16-sector PIO transfers, LBA addressing
> wd1: 39266 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 80418240 sectors
> wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
> wd1(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
> pciide0: secondary channel configured to native-PCI mode
> atapibus0 at pciide0 channel 1: 2 targets
> cd0 at atapibus0 drive 0: <CRD-8322B, 1998/09/24, 1.05> type 5 cdrom removable
> cd0: drive supports PIO mode 4, DMA mode 2
> cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
> ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI bridge (rev. 0x13)
> pci2 at ppb1 bus 2
> pci2: i/o space, memory space enabled
> ahc0 at pci2 dev 3 function 0
> ahc0: OptionMode = 3
> ahc0: interrupting at ivec 18
> ahc0: aic7892 Wide Channel A, SCSI Id=7, 16/255 SCBs
> scsibus0 at ahc0: 16 targets, 8 luns per target
> pcons0 at mainbus0
> No counter-timer -- using %tick at 333MHz as system clock.
> Using %tick -- intr in 3330000 cycles...done.
> scsibus0: waiting 2 seconds for devices to settle...
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x8
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): Queuing a BDR SCB
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x45
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): no longer in timeout, status = 0
> ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x7
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): Queuing a BDR SCB
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x8
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): no longer in timeout, status = 0
> ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x42
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): Queuing a BDR SCB
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x9
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): no longer in timeout, status = 0
> ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x42
> SCSIRATE == 0x0
> 0x0
> probe(ahc0:0:0:0): Queuing a BDR SCB
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x44
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): no longer in timeout, status = 0
> ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0xa
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): Queuing a BDR SCB
> probe(ahc0:0:0:0): SCB 70 - timed out while idle, SEQADDR == 0x43
> SCSIRATE == 0x0
> probe(ahc0:0:0:0): no longer in timeout, status = 0
> ahc0: Issued Channel A Bus Reset. 1 SCBs aborted
--
Adrien Auzanneau.
http://ada.netbsd-fr.org/